Specifying a Syslog server | Brocade Communications Systems 6650

10 Syslog service configuration

Brocade#show logging		flushes, 0 overruns)
Syslog logging: enabled (0 messages dropped, 0
Buffer logging: level ACDMEINW, 16 messages logged
level code: A=alert C=critical D=debugging		M=emergency E=error
I=informational N=notification		W=warning
Static Log Buffer:	Power supply 2 is up
0d00h00m17s:I:System: Stack unit 1

0d00h00m14s:A:System: Stack unit 1 Temperature 53.0 C degrees, warning level 0.0 C degrees, shutdown level 85.0 C degrees

0d00h00m14s:W:System: Temperature is over warning level on unit 1

Dynamic Log Buffer (50 lines): 3d00h21m29s:I:running-config was changed by from console 2d21h52m07s:I:running-config was changed by from console 1d11h35m29s:I:VLAN: Id 20 deleted by user from console session 1d02h42m03s:I:running-config was changed by from console 0d00h01m38s:D:DHCPC: Stopped DHCP Client service 0d00h00m14s:I:System: Interface ethernet 1/2/4, state up 0d00h00m14s:I:System: Interface ethernet 1/2/3, state up 0d00h00m14s:I:System: Interface ethernet 1/2/2, state up 0d00h00m14s:I:System: Interface ethernet 1/2/1, state up 0d00h00m14s:I:System: Interface ethernet mgmt1, state up 0d00h00m08s:D:DHCPC: starting dhcp client service on 69 port(s)

Disabling or re-enabling Syslog

Syslog is enabled by default. To disable it, enter the logging on command at the global CONFIG level.

Brocade(config)#no logging on

Syntax: [no] logging on [<udp-port>]

The <udp-port>parameter specifies the application port used for the Syslog facility. The default is 514.

To re-enable logging, re-enter the logging on command.

Brocade(config)#logging on

This command enables local Syslog logging with the following defaults:

•Messages of all severity levels (Emergencies – Debugging) are logged.

•Up to 50 messages are retained in the local Syslog buffer.

•No Syslog server is specified.

Specifying a Syslog server

To specify a Syslog server, enter the logging host command.

Brocade(config)#logging host 10.0.0.99

Syntax: logging host <ip-addr> <server-name>

238	Brocade ICX 6650 Administration Guide
	53-1002600-01

Image 256

Brocade Communications Systems 6650 manual Disabling or re-enabling Syslog, Specifying a Syslog server

Contents

Brocade ICX 6650 Administration Guide Brocade ICX 6650 Administration Guide Title Publication number Summary of changes Date Contents Chapter Operations, Administration, and Maintenance Chapter Ports on Demand Licensing Chapter IPv6 Configuration on Brocade ICX 6650 Switch Full Layer 3 IPv6 feature support Chapter Snmp Access Snmp overview FDP configuration FDP OverviewDisplaying FDP information Clearing FDP and CDP information Digital optical monitoring configuration limitations Setting the alarm intervalDisplaying information about installed media Digital optical monitoring Viewing configuration information Basic system managementViewing system information Viewing port statistics Local user password changes NIAP-CCEVS certified Brocade equipment Ironware releases Xii Brocade ICX 6650 Administration Guide 53-1002600-01 Supported hardware and software AudienceBrocade ICX 6650 slot and port numbering Command syntax conventions Command Option, option Argument, arg ArgumentsDocument conventions Text formatting Show WWN Additional information Related publicationsBrocade resources Document feedback Getting technical helpOther industry resources Brocade ICX 6650 slot and port numbering Feature This chapterManagement port overview How the management port works CLI Commands for use with the management port Syntax show running-config interface management numSyntax show interfaces management num Syntax show interfaces brief management num Syntax show statistics management num Logging on through the CLISyntax show statistics brief management num Online help Command completionScroll control Line editing commands Using slot number, and port number with CLI commandsCtrl+Key combination Description Searching and filtering output from CLI commands Searching and filtering output from Show commandsCLI nomenclature on Brocade ICX 6650 models Displaying lines containing a specified string Displaying lines starting with a specified string Searching and filtering output at the --More-- promptResults of the search are displayed Filtered results are displayed Using special characters in regular expressionsCharacter Operation Character Operation Creating an alias for a CLI command Configuration notes for creating a command aliasSyntax unalias alias-name Syntax alias Brocade ICX 6650 Administration Guide 53-1002600-01 Using slot number, and port number with CLI commands Basic System Parameters Basic Port Parameters Basic system parameter configuration Entering system administration information Snmp parameter configurationBasic system parameter configuration Specifying an Snmp trap receiver Specifying a single trap source Syntax snmp-server host ip-addr0 1 string port value Setting the Snmp trap holddown time Syntax no snmp-server enable traps holddown-time secsDisabling Snmp traps Snmp Layer 2 traps Disabling Syslog messages and traps for CLI access Syntax no snmp-server enable traps trap-typeSyntax no enable snmp ve-statistics Displaying virtual routing interface statistics Syntax show logging Examples of Syslog messages for CLI accessDisabling the Syslog messages and traps Syntax no logging enable user-login Cancelling an outbound Telnet sessionSpecifying an Sntp server Syntax show sntp associations Syntax no sntp poll-intervalField Description Output from the show sntp associations details command Syntax show sntp associations details Configuring the device as an Sntp server Configuring the device as an Sntp serverSyntax show sntp status Sntp server-mode authentication-key 2 $QHMiR3NzQA= Enabling broadcast mode for an Sntp client Output from the show sntp server-modecommandDisplaying Sntp server information Syntax show sntp server-mode Setting the system clock Syntax sntp broadcast client System time for daylight saving time. command New start and end dates for US daylight saving timeSyntax sntp sync Syntax no clock summer-time CLI banner configuration Setting a message of the day bannerLimiting broadcast, multicast, and unknown unicast traffic Syntax no clock timezone us timezone-type Use the no form of the command to disable the requirement Syntax no banner motd require-enter-key Setting a privileged Exec CLI level banner Local MAC address for Layer 2 management trafficSyntax no banner execmode delimiting-character Syntax no banner incoming delimiting-character Basic port parameter configuration Assigning a port nameSyntax no use-local-management-mac Syntax port-name text Port speed and duplex mode modification Port speed and duplex mode configuration syntaxBasic port parameter configuration Syntax speed-duplex value Syntax no speed-duplex 10g-full 1000-full-master Modifying port duplex mode Port duplex mode configuration syntaxValue can be one of the following Full Half Auto default Maximum port speed application notes Flow control configuration Flow control configuration notesDisabling or re-enabling a port Disabling or re-enabling flow control Syntax no flow-control Negotiation and advertisement of flow controlSyntax no flow-control neg-on Symmetric flow control on Brocade ICX 6650 devices Displaying flow-control status 1G or 10G ports About XON and Xoff thresholds40G ports Interpacket Gap IPG on a Brocade ICX 6650 switch Changing the Gbps fiber negotiation modeIPG configuration notes Enabling and disabling symmetric flow control Port flap dampening configuration Port flap dampening configuration notesSyntax gig-default neg-full-auto auto-gig neg-off Port priority QoS modification Configuring port flap dampening on an interface Configuring port flap dampening on a trunkRe-enabling a port disabled by port flap dampening Displaying ports configured with port flap dampening Syslog messages for port flap dampening Syntax show link-error-disable allColumn Description Recovering disabled ports Port loopback detection configuration notesPort loop detection Types of loop detection Configuring a global loop detection interval Configuring the device to automatically re-enable portsEnabling loop detection Syntax no loop-detection Specifying the recovery time interval Syntax no errdisable recovery cause loop-detectionSyntax no errdisable recovery interval seconds Clearing loop-detection Syntax show loop-detection resource Displaying loop detection resource informationFieldDescription Syslog message due to disabled port in loop detection Loop Detection is Enabled Basic port parameter configuration Operations, Administration, and Maintenance Feature Brocade ICX 6650 Software versions installed and running on a device OAM OverviewDetermining the flash image version running on the device Brocade ICX 6650 devices Displaying the boot image version running on the device Displaying the image versions installed in flash memorySoftware versions installed and running on a device Boot code version is shown in bold type Use the following command syntax to verify the flash image Flash image CLI commandsFlash image verification Viewing the contents of flash files Software upgradesImage file types Using Snmp to upgrade software Using Snmp to upgrade softwareSyntax show dir Syntax copy flash console filename Snmp-server community string ro rw Software reboot Displaying the boot preferenceSoftware boot configuration notes Software reboot Loading and saving configuration files Loading and saving configuration filesSyntax show boot-preference Logging changes to the startup-config file Syntax no logging enable config-changed Copying a configuration file to or from a Tftp server Dynamic configuration loadingDynamic configuration usage considerations Preparing the configuration file CLI responds like this Following command line will not initiate batch mode Loading and saving configuration files with IPv6 Using the IPv6 copy commandCopying a file from the running or startup configuration Copying a file to an IPv6 Tftp server Copying a file to the running or startup configuration Loading and saving configuration files with IPv6Copying a file from an IPv6 Tftp server Copying a file to flash memory IPv6 ncopy command IPv6 Tftp server file upload Using Snmp to save and load configuration information Erasing image and configuration files System reload schedulingReloading at a specific time Syntax reload at hhmmss mm-dd-yyprimary secondary Diagnostic error codes and remedies for Tftp transfers Canceling a scheduled reloadError Message Explanation and action Code Reloading after a specific amount of time Network connectivity testing Network connectivity testingPinging an IPv4 address Network connectivity testing Tracing an IPv4 route Network connectivity testing Feature Brocade ICX Ports on Demand Overview PoD licensing configuration tasks Ports on Demand terminologyPoD licensing rules Ports on Demand terminology Configuration task Reference Obtaining a PoD license Shows the Software Portal Login window Brocade Software Portal Login window License Management Welcome window PoD licensing configuration tasks Brocade ICX 6650 Administration Guide 53-1002600-01 LID Shows an example of the license query results Transferring a PoD license Syslog message informationPorts on Demand Licensing Front panel PoD PoD licenses Rear panel Flexible Ports on DemandPorts on Demand Licensing Enabling ports on the front panel Ports on Demand Licensing PoD licensesTrial licenses are not available for PoD licensing License SKU License Name Function Example, the license is copied to unit Syntax scp licensefileonhost user@IPaddresslicenseunit id Deleting a ICX6650-10G-LIC-POD license Example above, the license is copied to unit Syntax show pod Enabling ports on the rear panelIPaddress variable is the address of the IPv4 Tftp server Syntax no fpod-40g-enable group groupID Enter the following command to disable the ports in group Enable ports for groupEnable ports in group Disabling the FPoD ports on the rear panel Deleting a 10 GbE or 40 GbE license Viewing information about PoD licenses Syntax license delete unit unitid all index licenseindex Viewing information about PoD licenses Displaying general license information for PoD portsSyntax show license Syntax show license unit unitid Syntax show license unit unitid index indexnumber Field Description Lic-Used Field Description 40GigabitEthernet1/2/1 is up, line protocol is up Viewing information about PoD licenses IPv6 Configuration on Brocade ICX 6650 Switch IPv6 copy Using the IPv6 copy command on Full Layer 3 IPv6 feature support IPv6 addressing overview IPv6 address types IPv6 addressing overview IPv6 address types Address Description Address structure Type IPv6 stateless auto-configuration IPv6 CLI command supportIPv6 command Description Switch code Router code Description Switch code Router code IPv6 host address on a Layer 2 switch Syntax no ipv6 enable Syntax ipv6 address ipv6-addresslink-local Configuring basic IPv6 connectivity on a Layer 3 switch IPv6 configuration on each router interfaceEnabling IPv6 routing Syntax no ipv6 unicast-routing Ospf Configuring a link-local IPv6 address on an interface Configuring basic IPv6 connectivity on a Layer 3 switch Configuring an IPv6 anycast address on an interface Configuring IPv4 and IPv6 protocol stacksSyntax ip address ip-addresssub-net-masksecondary Configuring IPv6 management ACLs Syntax no ipv6 access-list ACL name Restricting Snmp access to an IPv6 node Configuring Snmp V3 over IPv6Configuring Sntp over IPv6 Specifying an IPv6 Snmp trap receiver IPv6 traceroute IPv6 TelnetEstablishing a Telnet session from an IPv6 host Syntax traceroute ipv6 ipv6-address Defining an IPv6 DNS entrySyntax no ipv6 dns domain-name domain name Pinging an IPv6 address Configuring an IPv6 Syslog server Viewing IPv6 Snmp server addresses Disabling IPv6 on a Layer 2 switch Static IPv6 route configurationDisabling router advertisement and solicitation messages Configuring a static IPv6 route Dest-ipv6-prefix parameter Parameter Configuration details StatusPrefix-length parameter IPv6 over IPv4 tunnel configuration notes Configuring a manual IPv6 tunnelIPv6 over IPv4 tunnels IPv6 over IPv4 tunnels Clearing IPv6 tunnel statistics Displaying IPv6 tunnel information Displaying a summary of tunnel informationDisplaying tunnel interface information Syntax clear ipv6 tunnel number Displaying interface level IPv6 settings Syntax show interfaces tunnel number Display command above reflects the following configuration Ecmp load sharing for IPv6 Ecmp load sharing for IPv6 Changing the maximum load sharing paths for IPv6 Disabling or re-enabling Ecmp load sharing for IPv6Displaying Ecmp load-sharing information for IPv6 IPv6 Icmp feature configuration Configuring Icmp rate limitingIPv6 Icmp feature configuration Syntax ipv6 icmp error-interval interval number-of-tokens IPv6 neighbor discovery configuration IPv6 neighbor discovery configurationEnabling IPv6 Icmp redirect messages Syntax no ipv6 redirects Neighbor solicitation and advertisement messages IPv6 neighbor discovery configuration notesNeighbor discovery is not supported on tunnel interfaces Router advertisement and solicitation messages Neighbor redirect messages Setting IPv6 router advertisement parameters Here is another example with a specified range Prefixes advertised in IPv6 router advertisement messages Enabling and disabling IPv6 router advertisements Setting flags in IPv6 router advertisement messagesSyntax no ipv6 nd suppress-ra Configuring reachable time for remote IPv6 nodes Configuration notes and feature limitations for IPv6 MTUIPv6 MTU IPv6 MTU Changing the IPv6 MTU Static neighbor entries configurationSyntax no ipv6 mtu bytes Limiting the number of hops an IPv6 packet can traverse IPv6 source routing security enhancementsClearing global IPv6 information Syntax no ipv6 hop-limit number Clearing IPv6 neighbor information Clearing the IPv6 cacheClearing global IPv6 information Displaying global IPv6 information Clearing IPv6 routes from the IPv6 route tableClearing IPv6 traffic statistics Displaying IPv6 cache information Displaying IPv6 interface information 142 Brocade ICX 6650 Administration Guide 53-1002600-01 Icmp Displaying IPv6 neighbor information Displaying the IPv6 route table Displaying local IPv6 routers Syntax show ipv6 router Displaying IPv6 TCP informationPort Syntax show ipv6 tcp connections Free TCP = percentage General IPv6 TCP connection fields = percentage Location of the TCP Syntax show ipv6 traffic Displaying IPv6 traffic statisticsField Description IPv6 statistics ICMP6 statistics Applies to received only TCP statistics Snmp Access Snmp overview Snmp community strings Encryption of Snmp community stringsAdding an Snmp community string Snmp community strings Snmp-server community 1 encrypted-string rw Displaying the Snmp community strings Syntax show snmp server Configuring your NMS Configuring Snmp version 3 on Brocade ICX 6650 devicesUser-based security model Defining the engine id Defining an Snmp group Snmp version 3. If you want commandSyntax no snmp-server engineid local hex-string Defining an Snmp user account 162 Brocade ICX 6650 Administration Guide 53-1002600-01 Syntax system-max view number-of-views Defining Snmp viewsSyntax no snmp-server view name mibtree included excluded Snmp version 3 traps To delete a view, use the no parameter before the commandSnmp version 3 traps Defining the UDP port for Snmp v3 traps Trap MIB changes Restricting Snmp Access to an IPv6 Node Specifying an IPv6 host as an Snmp trap receiverSnmp v3 over IPv6 Backward compatibility with SMIv1 trap format Displaying Snmp Information Displaying the Engine IDDisplaying Snmp Information Syntax show snmp engineid Displaying Snmp groups Displaying user informationInterpreting varbinds in report packets Syntax show snmp group Snmp v3 configuration examples Simple Snmp v3 configurationMore detailed Snmp v3 configuration Snmp v3 configuration examples 170 Brocade ICX 6650 Administration Guide 53-1002600-01 FDP Overview FDP Overview CDP packets FDP configuration Changing the FDP update timerEnabling FDP globally Enabling FDP at the interface level Syntax no fdp timer secs Displaying FDP informationChanging the FDP hold time Displaying neighbor information This line Displays Entry addresses Brocade ICX 6650 Administration Guide 175 53-1002600-01 Clearing FDP and CDP information Displaying FDP information for an interfaceDisplaying FDP and CDP statistics Clearing FDP and CDP neighbor information CDP packets Enabling interception of CDP packets globallyEnabling interception of CDP packets on an interface Clearing FDP and CDP statistics Displaying CDP information Displaying neighbors Displaying CDP entries Syntax show fdp entry * device-id Clearing CDP information To clear CDP statistics, enter the following commandDisplaying CDP statistics Lldp and LLDP-MED Lldp terms used in this chapter Supported Lldp features Lldp terms used in this chapter Lldp overview Illustrates Lldp connectivity Benefits of Lldp LLDP-MED overviewLLDP-MED overview Benefits of LLDP-MED LLDP-MED connectivity Lldp transmit mode General Lldp operating principlesLLDP-MED class Lldp operating modes Lldp receive mode Lldp packets Lldp TLVs TLV supportOrganizationally-specific TLVs LLDP-MED TLVs Mandatory TLVsChassis ID Chassis ID TLV is always the first TLV in the Lldpdu Port ID TLV packet format TTL value Syslog messages MIB supportMIB support TTL TLV format is shown below Lldp configuration Lldp configuration notes and considerationsLldp configuration Global task Default behavior / value when Lldp is enabled Enabling and disabling Lldp Changing a port Lldp operating modeEnabling support for tagged Lldp packets Enabling and disabling receive only mode Enabling and Disabling Transmit Only Mode Specifying the maximum number Lldp neighbors per device Maximum number of Lldp neighborsSyntax no lldp max-total-neighbors value Specifying the maximum number Lldp neighbors per port Enabling Lldp Snmp notifications and Syslog messagesSyntax no lldp max-neighbors-per-port value Changing the minimum time between Lldp transmissions Syntax no lldp transmit-delay secondsSyntax no lldp snmp-notification-interval seconds Changing the interval between regular Lldp transmissions Changing the holdtime multiplier for transmit TTLSyntax no lldp transmit-interval seconds Syntax no lldp transmit-hold value Syntax no lldp reinit-delay seconds Changing the minimum time between port reinitializationsLldp TLVs advertised by the Brocade device General system information for Lldp Management Address Port description System capabilities System description System name CapabilitiesVlan name Untagged Vlan ID Link aggregation TLV MAC and PHY configuration status LLDP-MED configuration LLDP-MED configurationThis section provides the details for configuring LLDP-MED Maximum frame size Default behavior / value Changing the fast start repeat count Syntax no lldp med fast-start-repeat-count value Defining a location id Coordinate-based location Example coordinate-based location configuration Example coordinate-based location advertisement Configuring civic address location Type value elem CA type value elem CA type value LLDP-MED configuration Elements used with civic address Description Acceptable values / examples Type Example civic address location advertisement Configuring emergency call serviceNumber variable is a number from 10 to 25 digits in length Defining an LLDP-MED network policy LLDP-MED network policy configuration syntaxExample ECS Elin location advertisements 216 Brocade ICX 6650 Administration Guide 53-1002600-01 LLDP-MED attributes advertised by the Brocade device LLDP-MED capabilities Lldp configuration summary Displaying Lldp statistics and configuration settingsLLDP-MED attributes advertised by the Brocade device Displaying Lldp statistics Syntax show lldp Clear lldp statistics all command was issued Syntax show lldp statistics Displaying Lldp neighbors Syntax show lldp neighbors Displaying Lldp configuration details Displaying Lldp neighbors detail Resetting Lldp statistics Clearing cached Lldp neighbor information Digital optical monitoring configuration limitations Digital optical monitoringEnabling digital optical monitoring Syntax no optical-monitor Displaying information about installed media Setting the alarm intervalSyntax no optical-monitor alarm-interval Empty Viewing optical monitoring information Syntax show media slot slot ethernet stack-unit/slot/port Viewing optical transceiver thresholds Status value Description Syslog messages for optical transceivers Syntax show optic threshold stack-unit/slot/port Syslog About Syslog messages Displaying Syslog messages Enabling real-time display of Syslog messages Enabling real-time display for a Telnet or SSH sessionSyntax no logging console Syntax terminal monitor Syslog service configuration Displaying the Syslog configurationSyslog service configuration Displaying real-time Syslog messages Static and dynamic buffers Field Definition Time stamps Clearing log entriesSyntax clear logging dynamic-buffer static-buffer Brocade ICX 6650 Administration Guide 237 53-1002600-01 To specify a Syslog server, enter the logging host command Disabling or re-enabling SyslogSpecifying a Syslog server Syntax no logging on udp-port Specifying an additional Syslog server Disabling logging of a message levelChanging the number of entries the local buffer can hold Syntax no logging buffered level num-entries Changing the log facility Local buffer configuration notesSyntax logging facility facility-name Displaying TCP or UDP port numbers in Syslog messages Displaying interface names in Syslog messagesSyntax no Ip show-portname Syslog reboot configuration considerations Retaining Syslog messages after a soft rebootClearing the Syslog messages from the local buffer Basic system management Viewing system information Viewing configuration information Syntax show version Viewing port statistics Syntax show optionSyntax show statistics ethernet stack-unit/slot/port Port statistics Parameter Description Basic system management Port statisticsStatistics Viewing STP statistics Clearing statistics Syntax clear option Viewing egress queue counters Syntax show interface ethernet stack-unit/slot/port Rmon support Maximum number of entries allowed Rmon control tableClearing the egress queue counters Syntax clear statistics ethernet stack-unit/slot/port Statistics Rmon group Rmon supportSyntax show rmon statistics ethernet stack-unit/slot/port ParameterDefinition Rmon support Export configuration and statistics Parameter Definition History Rmon group Alarm Rmon groupEvent Rmon group SFlow SFlow version Extended router information SFlow support for IPv6 packetsExtended gateway information SFlow configuration considerations IPv6 packet samplingSFlow and hardware support SFlow and CPU utilization SFlow and source port Configuring and enabling sFlowSFlow and sampling rate Specifying an sFlow collector on IPv4 devices Specifying the collectorSyntax no sflow destination ip-addrdest-udp-port Changing the polling interval Changing the sampling rateSpecifying an sFlow collector on IPv6 devices Syntax no sflow destination ipv6 ip-addrdest-udp-port Configuration considerations Configured rate and actual rateChange to global rate Module rate Changing the default sampling rate Syntax no sflow sample numChanging the sampling rate of a module Changing the sampling rate on a port Changing the sampling rate for a trunk port Command syntax for enabling sFlow forwarding Enabling sFlow forwardingChanging the sFlow source port Syntax no sflow source-port num SFlow version 5 feature configuration Syntax no sflow enable Syntax no sflow forwarding Specifying the sFlow version format Specifying the sFlow agent IP addressSpecifying the version used for exporting sFlow data Syntax no sflow agent-ip ipv4-addr Specifying the maximum flow sample size Syntax no sflow version 2Syntax no sflow max-packet-size size Syntax no sflow export system-info Displaying sFlow information Enabling the sFlow agent to export CPU-directed dataSyntax no sflow export cpu-traffic Specifying the sampling rate for exported CPU-directed data Syntax show sflow SFlow SFlow information Clearing sFlow statisticsSyntax clear statistics Utilization list for an uplink port Utilization list for an uplink port command syntaxUtilization list for an uplink port Displaying utilization percentages for an uplink Syntax show relative-utilization num 272 Brocade ICX 6650 Administration Guide 53-1002600-01 Brocade Syslog messages Message ExplanationFan num, location , failed Mac-address on portnum Syslog messages Brocade Syslog messages PCI-config-register-offset PCI-bus-number, DevPCI-device-number, Reg Offset Addr memory-address Message level Explanation Level shutdown-degrees C degreesFrom session-id Username from session-id filter User username from session-id Root ID root-id Stp-state Vlan-id MAC address any MAC address any, dst mac = DestinationIP=ipaddr Port-number Fan speed Unit/slot/port to Unit/slot/port on VLANs vlan-id to Vlan-idUnit/slot/port on vlan-id Unit/slot/port on Vlan vlan-id Mac-address MgmtPriChg Mac-address MsgAgeExpiryVlan vlan-id interface portnum STP Mac-address RootPort portnum Portnum DOT1X Port portid Mac macaddress Rid router-id, intf addr ip-addr Macaddress on port portidState ospf-state 286 Brocade ICX 6650 Administration Guide 53-1002600-01 Pkt type pkt-type Ip-addr, pkt type type Type Rid router-id, limit num LSA id lsa-id, LSA rid lsa-router-idArea area-id, LSA type lsa-type Ospf-state Brocade ICX 6650 Administration Guide 291 53-1002600-01 Interface configuration error has occurred Rid router-id, area area-id Nbr ip-addr, state ospf-state Rid router-id, nbr addr ip-addr Mac-address State vrrp-stateMac-addr interface portnum List ACL-num denied ip-proto Ethernet portnum mac-addrEportnum, address mac-address Portnum src macaddr mac-addr Chassis temperature has risen above the warning level 298 Brocade ICX 6650 Administration Guide 53-1002600-01 NIAP-CCEVS certified Brocade equipment Ironware releases Local user password changesBrocade product Brocade IronWare Discussed Software version 300 Brocade ICX 6650 Administration Guide 53-1002600-01 Index Lldp advertise mac-phy-config-status ports Lldp enable receive portsIpv6 nd prefix-advertisement,134 Clear fdp table, 176 Brocade ICX 6650 Administration Guide 303 53-1002600-01 FDP Icmp 131 LLDP-MED 266 Snmp SSH XON and Xoff thresholds 312 Brocade ICX 6650 Administration Guide 53-1002600-01