Variable Scan, Vertical Frequency | Christie Digital Systems CX67

Appendix A: Glossary

Variable Scan	' The ability of a projector to synchronize to inputs with frequencies within a specified
	range.
Vertical Frequency	' The frequency at which images are generated. Vertical frequencies vary amongst
	sources. Also called vertical scan rate.
Vertical Offset	' The difference between the center of the projected image and the center of the
	projector lens. For this projector, this value is expressed as the maximum percentage
	of the image that can be projected above or below the lens center without degrading
	the image quality. Vertical offset ranges depend on the type of lens in use, and
	whether or not the image is offset horizontally at the same time.
Video	' The signal that is used by display devices (such as projectors) to generate an image.
	This term also refers to the output of video tape/disk players and computers.
Video Decoder	' An optional device that converts NTSC 3.58, NTSC 4.4, PAL, PAL-N, PAL-M or
	SECAM to RGB video.
Video Standard	' A specific type of video signal, such as NTSC, PAL, SECAM. This projector can
	automatically recognize and interpret the incoming standard and display accordingly.
Viewing Angle	' Screens do not reflect equally in all directions. Most light is reflected in a conical
	volume centered around the "line of best viewing". Maximum brightness is perceived
	if you are within the viewing cone defined by the horizontal and vertical viewing
	angles.
White Balance	' The color temperature of white used by the projector.
White Field	' The area of an image that is white only. For example, a full white field is an image
	that is white everywhere. A 10% white field is a white area (usually rectangular) that
	occupies 10% of the image; the remaining 90% is black.
YCbCr	' A high-end digital component video signal.
YPbPr	' A high-end analog component video signal. Sometimes called YUV, Component, or
	Y, R-Y, B-Y, the YPbPr signal bypasses the video decoder in this projector.
YUV	' See YPbPr.

A-6 RPMX/CX50/CX60/CX67 User’s Manual

Image 67

Christie Digital Systems CX67 Variable Scan, Vertical Frequency, Vertical Offset, Video Decoder, Video Standard, YCbCr

Contents

Table of Contents For detailed product specifications, see Section Key FeaturesIntroduction For Rpmx For CX50/CX60/CX67 Vertical configurationComponents How the projector works Purchase Record Purchase Record and ServicingPage Source Source SetupConnections Analog VGA Connector Source Setup Video Loop Through Composite Video Loop Through Serial Port Connections If using a computer Single Projector 10. Multiple Projector RS-232 Connection Requirements Power ConnectionPage Projector Overview OperationProjection Head Module Normal LED Status Keypad Commands Using the Keypad FAN LED will no longer be illuminated Refer to 3.7 Using Multiple Projectors for more details Accessing the Main Menu Adjusting Slidebars Options Adjusting an ImageTo save or Exit to Presentation Size and Position Menu Resize Presets No Resizing Tiled Resize Presets Vert Stretch SizePixel Tracking Position Pixel phase Contrast Color SetupBrightness 12. Gamma options Video Options 13. Creating a Custom Color Temperature 15. Input Video Black Input Levels for experienced users only Black Levels & Input Drives White Boost Mode Memory StatusInput Select Language Image Orientation Communication Menu Preference 25. Assigning Projector ID Tiling Setup Color and Uniformity 27. Expanded Options in Resize Presets Diagnostics & Service Lamp Menu Choosing a Lamp Power Optimizes Sets to Default System Status Auto Setup Projectors Using Multiple Display Wall When matching screens in a display wall, do the followingPreliminary Setup Defining the Size Primary Color Adjustment Enable Primary Color AdjustmentAdjust Color Temperature Status LED Codes Error Codes Lamp failure, Ballast DMD errorError, Lamp shut off Lamp strike failurePage Maintenance Attachments Power cord Cleaning and Maintenance Batteries ReplacementLamp Replacing Keypad Remove the lamp Access the lamp module Close lamp door and record new lamp serial number Install a new lampSee also, 3.4 The Lamp Menu in Section For Rpmx 38-GFX101-01, CX67 38-GFX005-01 Figure Projection Lens Focus Projector is on, but no image is displayed TroubleshootingSymptom Projector does not power on when the Power key is pressed Display is reversed and/or upside down… Symptom The display is jittery or unstable…Symptom The display has suddenly frozen… Display is faint… Colors in the display are inaccurate… Display is not sharp or clean…Display is noisy… Specifications RS-232 Control Signal Infrared IR Control InputPicture Offset Adjustment Range Range of Motion DVI Input Lens Power RequirementsViewing Angle Lamps For RPMX-100U Weight including adjusterSize includes lens, adjuster and mounting rails For RPMX-100U 38-GFX101-01 For RPMX-100U 38-GFX004-xx For CX50-100U38-GFX003-xx For CX60-100U 38-GFX006-xx For CX67-100URegulatory Compliance ANSI/UL 60950 3rd Edition Specifications Glossary Color Shift Color TemperatureDisplay Setting Checkbox Horizontal Offset Input SignalHelp Screen Horizontal Frequency Ntsc Video Pixel PhaseResolution lens Resolution projector RS-422 Source SetupSwitcher RGB Video Video Decoder Variable ScanVertical Frequency Vertical Offset Acceptable Signal Types Acceptable RGB Input Signal Timing RPMX/CX50/CX60/CX67 User’s Manual B-3 Page Keypad Reference Page Serial Communication Cables Page Menu Tree Page Input Levels IndexAbout Power Level Switching Pixel Phase