Manuals / Cisco Systems / Computer Equipment / Network Router

Cisco Systems OL-20932-02 manual Mounting a Gateway or Optional Module, 1-14

Models: OL-20932-02

1 94

Download 94 pages 10.95 Kb

Page 22

Mounting a Gateway or Optional Module

Chapter 1 Overview

Mounting a Gateway or Optional Module

Mounting a Gateway or Optional Module

Each Cisco Physical Access Gateway and optional module includes two mounting brackets and four screws to mount the Gateway to the wall.

Wall Mounting a Gateway or Optional Module

Figure 1-9shows the three options for attaching the included wall-mount brackets to a module.

Figure 1-9 Three Options for Installing Wall Mount Brackets

1

4

5

2

4

5

3

4

187050

5

1	Option 1: Bottom end mounting	4	Mounting Brackets (included)

2	Option 2: Bottom side mounting	5	Screws

3	Option 3: Side mounting

	Cisco Physical Access Gateway User Guide
1-14	OL-20932-02

Image 22

Cisco Systems OL-20932-02 manual 1-14, Wall Mounting a Gateway or Optional Module

Contents

800 553-NETS Fax 408 Release 1.1.0 and higherCisco Systems, Inc 170 West Tasman Drive San Jose, CA Cisco Physical Access Gateway User GuideCisco Physical Access Gateway User Guide Turn the television or radio antenna until the interference stopsSafety Warnings Power OptionsContents The Cisco Physical Access GatewayStatement 1071-Warning Definition Safety WarningsConnecting a Cisco Input Module OverviewCisco Physical Access Gateway User Guide Environmental Specifications A-1Contents OL-20932-02Contents Cisco Physical Access Gateway User Guide OL-20932-02Obtaining Documentation and Submitting a Service Request Safety WarningsPreface Preface Cisco Physical Access Gateway User Guide viiiOL-20932-02 Cisco Physical Access Manager, page Optional Expansion Modules, page System Overview, page The Cisco Physical Access Gateway, pageSupport for Multiple Cisco Physical Access Gateways, page Installation and Configuration Summary, pageThe Cisco Physical Access Gateway System OverviewSupport for Multiple Cisco Physical Access Gateways Related DocumentationCisco PAM Cisco Physical Access ManagerCisco PAM Configuration Interface ApplianceOptional Expansion Modules Related DocumentationCisco Reader Module Module FeaturesGateway Cisco Input ModuleChapter 5, “Connecting a Cisco Output Module” Chapter 3, “Connecting a Cisco Reader Module”Chapter 4, “Connecting a Cisco Input Module” CAN Bus Connections for Optional ModulesInstallation and Configuration Summary Wires Door Device Wiring RequirementsWire Typicalsection on page 1-13 for more information Understanding Supervised and Unsupervised Input DevicesSuppressors on Output Device Connections” 1-10Figure 1-7 Example of a Supervised Door Sensor 1-11Cisco Physical Access Gateway User Guide Chapter 1 OverviewPower Options Current Draw Requirements Power Options and RequirementsPower Options Installing Surge Suppressors on Output Device Connections1-13 Installing Surge Suppressors on Output Device ConnectionsConnect Reader Devices with Module Power Off Figure 1-8 Sample Surge Suppressor Installation1-14 Mounting a Gateway or Optional ModuleWall Mounting a Gateway or Optional Module Table 1-5 Wall Mount Installation Kit Contents Wall Mount Installation Kit Contents1-15 Cisco Physical Access Gateway User GuideChapter 1 Overview Mounting a Gateway or Optional Module 1-16Cisco Physical Access Gateway User Guide OL-20932-02Overview, page Package Contents, page Installing and Configuring the Cisco Physical Access GatewayContents Installing the Cisco Physical Access Gateway, pageOverview Figure 2-1 Cisco Physical Access GatewayPackage Contents Physical Overview and Port DescriptionFast Ethernet interfaces-There are two 10/100 BASE-TX RJ-45 connectors Status LED StatusDescription Input Port LEDs Output Port LEDsProcedure Installing the Cisco Physical Access GatewayBefore You Begin, page Procedure, page Before You BeginDC power GND ground- Connects the DC ground wire to the Gateway PWR red D0 greenPWR red PWR redCP purple 2-10HCRD blue D0 green2-11 Normally Closed N.O. connection Normally Open N.O. connection2-12 2-13 CAN+ Connects to the positive terminal of the CAN bus CAN2-14 ETH0-Ethernet port for connecting the Gateway to the IP networkUnderstanding Network Time Protocol NTP Settings Configuring and Managing the Gateway Using a Direct ConnectionUnderstanding Network Time Protocol NTP Settings Connecting a PC to the Gateway Entering the Gateway Network SettingsConnecting a PC to the Gateway 2-16Entering the Gateway Network Settings 2-172-18 Note Changes do not take effect until savedStep 2 Enter the Current Password Step 3 Enter the New Password Changing the User Password2-19 Upgrading the Gateway Firmware Using a Direct Connection 2-20Option 1 Local Disk 2-21Option 2 Remote TFTP Server Displaying Serial Numbers and Other Information 2-22See the Cisco Physical Access Manager User Guide for more information Configuring the Gateway Using the Cisco Physical Access Manager2-23 Hard Reset Restore Factory Defaults Resetting the Cisco Physical Access GatewaySoft Reset Powercycle Soft Reset Powercycle, page Hard Reset Restore Factory Defaults, pageC H A P T E R Connecting a Cisco Reader ModuleOverview Figure 3-1 Cisco Reader ModuleAccess Layer switch Ethernet Cisco Access Gateway Cisco IP Network Package ContentsCisco Reader Module connected to the Cisco Physical Access Gateway Door and Related Hardware Door and Related HardwareCisco Physical Access Gateway User Guide Figure 3-3 Cisco Reader Module Ports and ConnectorsChapter 3 Connecting a Cisco Reader Module Physical Overview and Port DescriptionFigure 3-4 Cisco Reader Module Ports and Connectors Top View Input interfaces Input Port LEDs Installing the Cisco Reader ModuleStatus LEDs Output Port LEDsFigure 3-5 Power Connection for the Cisco Reader Module Page 5 Wire Connection 10 Wire Connection5 Wire Connection Chassis5 Wire Connection 3-1010 Wire Connection 5 Wire Connection3-11 Normally Open N.O. connection C Common3-12 Normally Closed N.O. connectionC H A P T E R Connecting a Cisco Input ModuleOverview Figure 4-1 Cisco Input ModuleDoor Readers Package ContentsInput/Output devices Cisco Physical Access Gateway User Guide Figure 4-3 Cisco Input Module Ports and ConnectorsChapter 4 Connecting a Cisco Input Module Physical Overview and Port DescriptionFigure 4-4 Cisco Input Module Ports and Connectors Top View Status LEDs Installing the Cisco Input ModuleInput Module LEDs Figure 4-5 Power Connections for the Input and Output Modules Figure 4-6 CAN Connections Input and Output Modules c. Connect the wires from the input devices Overview Connecting a Cisco Output ModuleCisco Physical Access Gateway User Guide C H A P T E RPackage Contents Cisco Physical Access Gateway User Guide Figure 5-3 Cisco Output Module Ports and ConnectorsChapter 5 Connecting a Cisco Output Module Physical Overview and Port DescriptionFigure 5-4 Cisco Output Module Ports and Connectors Top View Status LEDs Table 5-1 Output Module LEDsProcedure Installing the Cisco Output ModuleBefore You Begin Figure 5-5 Power Connections for the Cisco Output Module Figure 5-6 CAN Connections Input and Output Modules Cisco Physical Access Gateway User Guide Chapter 5 Connecting a Cisco Output ModuleInstalling the Cisco Output Module OL-20932-02Installing the Cisco Output Module 5-10Chapter 5 Connecting a Cisco Output Module Cisco Physical Access Gateway User GuideStatement 1004-Installation Instructions, page Safety WarningsStatement 369-Power over Ethernet PoE IEEE 802.3af, page Statement 1071-Warning DefinitionVaroitus TÄRKEITÄ TURVALLISUUSOHJEITA Aviso INSTRUÇÕES IMPORTANTES DE SEGURANÇA Este símbolo de aviso significa perigo. Você se encontra em uma situação em que há risco de lesões corporais. Antes de trabalhar com qualquer equipamento, esteja ciente dos riscos que envolvem os circuitos elétricos e familiarize-se com as práticas padrão de prevenção de acidentes. Use o número da declaração fornecido ao final de cada aviso para localizar sua tradução nos avisos de segurança traduzidos que acompanham o dispositivo Appendix 6 Safety Warnings Cisco Physical Access Gateway User Guide OL-20932-02Statement 369-Power over Ethernet PoE IEEE 802.3af StatementStatement 353-This Product Must be Connected Attention Ce produit doit être connecté à une source dalimentation électrique par câble Ethernet PoE conforme à la norme IEEE 802.3af ou à une source dalimentation limitée conforme à la norme IEC60950 Statement 1040-Product Disposal Statement 1004-Installation Instructions 6-106-11 Advarsel Les installasjonsinstruksjonene før systemet kobles til strømkildenCisco Physical Access Gateway User Guide 6-12Appendix 6 Safety Warnings OL-20932-02Environmental Specifications for the Cisco Reader Module, page A-2 Environmental SpecificationsEnvironmental Specifications for the Cisco Physical Access Environmental Specifications for the Cisco Input Module, page A-2Environmental Specifications for the Cisco Reader Module Environmental Specifications for the Cisco Input ModuleEnvironmental Specifications for the Cisco Output Module Cisco Physical Access Gateway User Guide Appendix A Environmental SpecificationsEnvironmental Specifications for the Cisco Output Module OL-20932-02