Manuals / Cisco Systems / Computer Equipment / Network Router

Cisco Systems OL-20932-02 manual Installing the Cisco Reader Module, Status LEDs, Input Port LEDs

Models: OL-20932-02

1 94

Download 94 pages 10.95 Kb

Page 54

Status LEDs

Chapter 3 Connecting a Cisco Reader Module

Installing the Cisco Reader Module

Status LEDs

Table 3-1describes the Gateway module status LEDs:

Table 3-1	Gateway LEDs

Status		Description

Input Port LEDs

OFF		Input is not configured

GREEN		Input is configured and in normal state

BLINKING GREEN		Input is configured, and is receiving and alarm or other data.

BLINKING RED		Input is configured, short

RED		Input is configured, open

Output Port LEDs

Off		Output not configured

Solid Green		Output configured and in default state

Blinking Green		Output configured and active

Installing the Cisco Reader Module

Installing the Cisco Reader Module is similar to installing the Gateway, except for the following:

•There are no Ethernet ports. The Cisco Reader Module is not directly connected to the IP network, and is not directly configured.

•The Cisco Reader Module does not support Power over Ethernet (PoE). The device is connected to a DC power source.

•The Cisco Reader Module must be terminated if it is the last device in a CAN wiring bus. See the “CAN Bus Connections for Optional Modules” section on page 1-7for more information.

Before You Begin

Before you install a Cisco Reader Module, verify the following:

•Verify that the module has access to a power source. See the “Power Options and Requirements” section on page 1-12for more information.

•Verify that you have the necessary mounting brackets or other hardware. See the “Mounting a Gateway or Optional Module” section on page 1-14.

Procedure

To install the Cisco Reader Module, perform the following procedure:

Step 1 Mount the module to a wall. See the “Mounting a Gateway or Optional Module” section on page 1-14for more information.

Step 2 Connect the module to the DC power source:

a.Insert a two-pin connector plug into the DC power port (Figure 3-5)

b.Connect the Voltage In (VIN) and ground (GND) wires.

Cisco Physical Access Gateway User Guide

3-6	OL-20932-02

Image 54

Cisco Systems OL-20932-02 manual Installing the Cisco Reader Module, Status LEDs, Input Port LEDs, Output Port LEDs

Contents

800 553-NETS Fax 408 Release 1.1.0 and higherCisco Systems, Inc 170 West Tasman Drive San Jose, CA Cisco Physical Access Gateway User GuideCisco Physical Access Gateway User Guide Turn the television or radio antenna until the interference stopsSafety Warnings Power OptionsContents The Cisco Physical Access GatewayStatement 1071-Warning Definition Safety WarningsConnecting a Cisco Input Module OverviewCisco Physical Access Gateway User Guide Environmental Specifications A-1Contents OL-20932-02Contents Cisco Physical Access Gateway User Guide OL-20932-02Safety Warnings Obtaining Documentation and Submitting a Service RequestPreface viii Preface Cisco Physical Access Gateway User GuideOL-20932-02 Cisco Physical Access Manager, page Optional Expansion Modules, page System Overview, page The Cisco Physical Access Gateway, pageSupport for Multiple Cisco Physical Access Gateways, page Installation and Configuration Summary, pageThe Cisco Physical Access Gateway System OverviewSupport for Multiple Cisco Physical Access Gateways Related DocumentationCisco PAM Cisco Physical Access ManagerCisco PAM Configuration Interface ApplianceOptional Expansion Modules Related DocumentationCisco Reader Module Module FeaturesGateway Cisco Input ModuleChapter 5, “Connecting a Cisco Output Module” Chapter 3, “Connecting a Cisco Reader Module”Chapter 4, “Connecting a Cisco Input Module” CAN Bus Connections for Optional ModulesInstallation and Configuration Summary Wires Door Device Wiring RequirementsWire Typicalsection on page 1-13 for more information Understanding Supervised and Unsupervised Input DevicesSuppressors on Output Device Connections” 1-10Figure 1-7 Example of a Supervised Door Sensor 1-11Cisco Physical Access Gateway User Guide Chapter 1 OverviewPower Options Current Draw Requirements Power Options and RequirementsPower Options Installing Surge Suppressors on Output Device Connections1-13 Installing Surge Suppressors on Output Device ConnectionsConnect Reader Devices with Module Power Off Figure 1-8 Sample Surge Suppressor InstallationMounting a Gateway or Optional Module 1-14Wall Mounting a Gateway or Optional Module Table 1-5 Wall Mount Installation Kit Contents Wall Mount Installation Kit Contents1-15 Cisco Physical Access Gateway User GuideChapter 1 Overview Mounting a Gateway or Optional Module 1-16Cisco Physical Access Gateway User Guide OL-20932-02Overview, page Package Contents, page Installing and Configuring the Cisco Physical Access GatewayContents Installing the Cisco Physical Access Gateway, pageOverview Figure 2-1 Cisco Physical Access GatewayPackage Contents Physical Overview and Port DescriptionFast Ethernet interfaces-There are two 10/100 BASE-TX RJ-45 connectors LED Status StatusDescription Input Port LEDs Output Port LEDsProcedure Installing the Cisco Physical Access GatewayBefore You Begin, page Procedure, page Before You BeginDC power GND ground- Connects the DC ground wire to the Gateway PWR red D0 greenPWR red PWR redCP purple 2-10HCRD blue D0 green2-11 Normally Open N.O. connection Normally Closed N.O. connection2-12 2-13 CAN+ Connects to the positive terminal of the CAN bus CAN2-14 ETH0-Ethernet port for connecting the Gateway to the IP networkUnderstanding Network Time Protocol NTP Settings Configuring and Managing the Gateway Using a Direct ConnectionUnderstanding Network Time Protocol NTP Settings Connecting a PC to the Gateway Entering the Gateway Network SettingsConnecting a PC to the Gateway 2-16Entering the Gateway Network Settings 2-172-18 Note Changes do not take effect until savedChanging the User Password Step 2 Enter the Current Password Step 3 Enter the New Password2-19 Upgrading the Gateway Firmware Using a Direct Connection 2-202-21 Option 1 Local DiskOption 2 Remote TFTP Server Displaying Serial Numbers and Other Information 2-22Configuring the Gateway Using the Cisco Physical Access Manager See the Cisco Physical Access Manager User Guide for more information2-23 Hard Reset Restore Factory Defaults Resetting the Cisco Physical Access GatewaySoft Reset Powercycle Soft Reset Powercycle, page Hard Reset Restore Factory Defaults, pageC H A P T E R Connecting a Cisco Reader ModuleOverview Figure 3-1 Cisco Reader ModuleAccess Layer switch Ethernet Cisco Access Gateway Cisco IP Network Package ContentsCisco Reader Module connected to the Cisco Physical Access Gateway Door and Related Hardware Door and Related HardwareCisco Physical Access Gateway User Guide Figure 3-3 Cisco Reader Module Ports and ConnectorsChapter 3 Connecting a Cisco Reader Module Physical Overview and Port DescriptionFigure 3-4 Cisco Reader Module Ports and Connectors Top View Input interfaces Input Port LEDs Installing the Cisco Reader ModuleStatus LEDs Output Port LEDsFigure 3-5 Power Connection for the Cisco Reader Module Page 5 Wire Connection 10 Wire Connection5 Wire Connection Chassis5 Wire Connection 3-1010 Wire Connection 5 Wire Connection3-11 Normally Open N.O. connection C Common3-12 Normally Closed N.O. connectionC H A P T E R Connecting a Cisco Input ModuleOverview Figure 4-1 Cisco Input ModulePackage Contents Door ReadersInput/Output devices Cisco Physical Access Gateway User Guide Figure 4-3 Cisco Input Module Ports and ConnectorsChapter 4 Connecting a Cisco Input Module Physical Overview and Port DescriptionFigure 4-4 Cisco Input Module Ports and Connectors Top View Installing the Cisco Input Module Status LEDsInput Module LEDs Figure 4-5 Power Connections for the Input and Output Modules Figure 4-6 CAN Connections Input and Output Modules c. Connect the wires from the input devices Overview Connecting a Cisco Output ModuleCisco Physical Access Gateway User Guide C H A P T E RPackage Contents Cisco Physical Access Gateway User Guide Figure 5-3 Cisco Output Module Ports and ConnectorsChapter 5 Connecting a Cisco Output Module Physical Overview and Port DescriptionFigure 5-4 Cisco Output Module Ports and Connectors Top View Status LEDs Table 5-1 Output Module LEDsInstalling the Cisco Output Module ProcedureBefore You Begin Figure 5-5 Power Connections for the Cisco Output Module Figure 5-6 CAN Connections Input and Output Modules Cisco Physical Access Gateway User Guide Chapter 5 Connecting a Cisco Output ModuleInstalling the Cisco Output Module OL-20932-02Installing the Cisco Output Module 5-10Chapter 5 Connecting a Cisco Output Module Cisco Physical Access Gateway User GuideStatement 1004-Installation Instructions, page Safety WarningsStatement 369-Power over Ethernet PoE IEEE 802.3af, page Statement 1071-Warning DefinitionVaroitus TÄRKEITÄ TURVALLISUUSOHJEITA Aviso INSTRUÇÕES IMPORTANTES DE SEGURANÇA Este símbolo de aviso significa perigo. Você se encontra em uma situação em que há risco de lesões corporais. Antes de trabalhar com qualquer equipamento, esteja ciente dos riscos que envolvem os circuitos elétricos e familiarize-se com as práticas padrão de prevenção de acidentes. Use o número da declaração fornecido ao final de cada aviso para localizar sua tradução nos avisos de segurança traduzidos que acompanham o dispositivo Appendix 6 Safety Warnings Cisco Physical Access Gateway User Guide OL-20932-02Statement 369-Power over Ethernet PoE IEEE 802.3af StatementStatement 353-This Product Must be Connected Attention Ce produit doit être connecté à une source dalimentation électrique par câble Ethernet PoE conforme à la norme IEEE 802.3af ou à une source dalimentation limitée conforme à la norme IEC60950 Statement 1040-Product Disposal Statement 1004-Installation Instructions 6-106-11 Advarsel Les installasjonsinstruksjonene før systemet kobles til strømkildenCisco Physical Access Gateway User Guide 6-12Appendix 6 Safety Warnings OL-20932-02Environmental Specifications for the Cisco Reader Module, page A-2 Environmental SpecificationsEnvironmental Specifications for the Cisco Physical Access Environmental Specifications for the Cisco Input Module, page A-2Environmental Specifications for the Cisco Reader Module Environmental Specifications for the Cisco Input ModuleEnvironmental Specifications for the Cisco Output Module Cisco Physical Access Gateway User Guide Appendix A Environmental SpecificationsEnvironmental Specifications for the Cisco Output Module OL-20932-02