Feature Overview
508148.568 | CMAC_LOG_RNG_RSP_SID_ASSIGNED | 2 |
|
508148.570 | CMAC_LOG_ADJUST_RANGING_OFFSET | 2408 |
|
508148.572 | CMAC_LOG_RANGING_OFFSET_SET_TO | 12018 |
|
508148.574 | CMAC_LOG_ADJUST_TX_POWER | 20 |
|
508148.576 | CMAC_LOG_POWER_LEVEL_IS | 33.0 | dBmV (commanded) |
508148.578 | CMAC_LOG_STATE_CHANGE | ranging_2_state | |
508148.580 | CMAC_LOG_RNG_REQ_QUEUED | 2 |
|
508155.820 | CMAC_LOG_RNG_REQ_TRANSMITTED |
|
|
508155.824 | CMAC_LOG_RNG_RSP_MSG_RCVD |
|
|
508155.826 | CMAC_LOG_ADJUST_RANGING_OFFSET |
| |
508155.826 | CMAC_LOG_RANGING_OFFSET_SET_TO | 11954 |
|
508155.828 | CMAC_LOG_RANGING_CONTINUE |
|
|
508165.892 | CMAC_LOG_RNG_REQ_TRANSMITTED |
|
|
508165.894 | CMAC_LOG_RNG_RSP_MSG_RCVD |
|
|
508165.896 | CMAC_LOG_ADJUST_TX_POWER |
| |
508165.898 | CMAC_LOG_POWER_LEVEL_IS | 31.0 | dBmV (commanded) |
508165.900 | CMAC_LOG_RANGING_CONTINUE |
|
|
508175.962 | CMAC_LOG_RNG_REQ_TRANSMITTED |
|
|
508175.964 | CMAC_LOG_RNG_RSP_MSG_RCVD |
|
|
508175.966 | CMAC_LOG_RANGING_SUCCESS |
|
|
Event 5—Establish IP Connectivity
After ranging is complete, the cable interface on the cable access router is UP. Now the cable access router accesses a remote DHCP server to get an IP address. The DHCP server sends a response containing the router’s IP address plus the TFTP server’s address, the Time of Day (TOD) server’s address, and the name of a configuration file containing additional configuration parameters. The
field shows that the IP connectivity was successful.
508175.968 | CMAC_LOG_STATE_CHANGE | dhcp_state |
508176.982 | CMAC_LOG_DHCP_ASSIGNED_IP_ADDRESS | 188.188.1.62 |
508176.984 | CMAC_LOG_DHCP_TFTP_SERVER_ADDRESS | 4.0.0.1 |
508176.986 | CMAC_LOG_DHCP_TOD_SERVER_ADDRESS | 4.0.0.32 |
508176.988 | CMAC_LOG_DHCP_SET_GATEWAY_ADDRESS |
|
508176.988 | CMAC_LOG_DHCP_TZ_OFFSET | 360 |
508176.990 | CMAC_LOG_DHCP_CONFIG_FILE_NAME | platinum.cm |
508176.992 | CMAC_LOG_DHCP_ERROR_ACQUIRING_SEC_SVR_ADDR |
|
508176.996 | CMAC_LOG_DHCP_COMPLETE |
|
Event 6—Establish the Time of Day
The Cisco uBR900 series accesses the Time of Day server for the current date and time, which is
used to create time stamps for logged events. Thefield indicates a successful time of day sequence.
508177.120 | CMAC_LOG_STATE_CHANGE | establish_tod_state |
508177.126 | CMAC_LOG_TOD_REQUEST_SENT |
|
508177.154 | CMAC_LOG_TOD_REPLY_RECEIVED | 3107617539 |
508177.158 | CMAC_LOG_TOD_COMPLETE |
|
Event 7—Establish Security
This event is currently bypassed by the Cisco uBR900 series because “full security” has not been fully defined by DOCSIS and is therefore not yet supported.
508177.160 | CMAC_LOG_STATE_CHANGE | security_association_state |
508177.162 | CMAC_LOG_SECURITY_BYPASSED |
|
