Maintenance | Conair UGR003/0800 guide

WARNING: Voltage Hazard

This equipment is powered by alternating cur- rent, as specified on the machine serial tag and data plate.

Device must be properly grounded. Improper grounding can result in severe personal injury and erratic machine operation.

Always disconnect and lock out the incoming main power source to the robot before perform- ing non-standard operating procedures such as routine maintenance. Only qualified personnel should perform troubleshooting procedures that require access to the electrical enclosure while power is on.

All wiring, disconnects, and fuses should be installed by qualified electrical technicians in accordance with electrical codes in your region. Always maintain a safe ground. Do not operate the equipment at power levels other than what is specified on the machine serial plate.

WARNING: High speed moving parts.

Do not enter maximum envelope area while machine is operating. The maximum envelope is the volume of space encompassing the maxi- mum designed movement of ALL robot parts, including the end of arm tooling, work piece and attachments.

Do not operate machine unless interlocks/safety devices are in place and function properly.

Robot may drop load. Do not walk under robot/ load. Failure to follow instructions could result in injury.

UGR003/0900

UCR-150L Robot

MAINTENANCE 5-3

Image 49

Conair UGR003/0800 manual Maintenance

Contents

UCR-150L Robot Date Document Number Introduction Table of Contents Maintenance Introduction HOW the User Guide is Organized Purpose User GuideYour Responsibility AS a User Read this SO no ONE Gets Hurt Page Description ROBOT? What isTypical Applications Robot Works HOW Wrist flip cylinder Robot Features Front view Side view Specifications Extended strip stroke Optional EquipmentEnd-of-arm tooling Installation Remove all packing material Unpacking the Boxes Installation Preparing for Installation Mounting pattern for the UCR-150L Robot Preparing the Platen Positioning the Robot Connecting the Robot Connect the SPI connector cable into Check to see what the power output is fromPlug the hand-held control into the control Tighten the adjustment screws on the block Setting Gripper PositionOpen the mold Hold the main arm and loosen the arm height Set the gripper height to the sprue Setting Strip Positions Adjusting Sprue Verification Switch Connecting AIR Pressure Adjusting the Speed Verifying motion controls permissives Verifying Electrical Interface Mold Full Open Verifying the Inputs Manual Testing Press the Stop button Automatic TestingPress the Auto/Recycle button Page Operation Before Starting Hand Control Features Stopping the Robot Starting the RobotEmergency Stopping Grips Viewing Information Operating Manually Starting Automatic Operation Press the Program button Choosing the MoldUse the Up and Down arrows Press the Enter button Press Stop button Programming Motion SequencePress Program button Continue to move through the motion Use the Forward arrow Press the Function button Programming HOME, Grip Vacuum Positions Use the right arrow to choose the setting Choose the function and settings you wantPress the Stop button to continue Inputs Monitoring INPUT/OUTPUT Enter the new timer value Setting Timer ValuesPress the Time button Press the Forward button Timer Setting Description LCD Displays Choosing Timer Settings Adjusting Traverse Movement Open the safety door and verify that there is Answering AN AlarmRestarting Automatic Operation Use the Motion Control buttons Maintenance Maintenance Features Maintenance Daily Preventative Maintenance Schedule Monthly Checking Electrical Connections Be sure the main power is disconnected Troubleshooting Before Beginning Identifying Cause of a ProblemFEW Words of Caution Error Display Area of problem Robot Does not Cycle Symptom Possible cause Solution Mold is Not Working Properly Safety interlock is on. Check the output and wiring ARM is Not Working Properly Strip Motion Is not Working Horizontal Motion There is no Gripper does not work Gripper Does not Work There is no vac Air pressure is incor Uum Rect Before YOU WE’RE Here to Help HOW to Contact Customer ServiceFrom outside the United States, call Appendix GUARANTEE/WARRANTY Electrical Diagrams Solenoid and Limit Switch Wiring Relay and IMM Interface Solenoid Valves Page PARTS/DIAGRAMS PARTS/LISTS Ref. Part No Description Traverse Cylinder IMR004/0800 UCR-150L Robot PARTS/DIAGRAMS P/D-5 Valve IMR004/0800 UCR-150L Robot PARTS/DIAGRAMS P/D-7 Valve Parts JSU6 Slide Base YSA10DC-50B Strip Cylinder U3-MA0-LS Main Arm Description Quantity Main Arm Slide Unit LM20UU Main Cylinder IMR004/0800 UCR-150L Robot PARTS/DIAGRAMS P/D-19 Wrist Flip TANSI6P Wrist Flip Cylinder IMR004/0800 UCR-150L Robot PARTS/DIAGRAMS P/D-23 Gripper Assembly D12 D9191 Assembly, Gripper, with LS-4 Gripper GXL-8F Controller HW-CB116B