Disconnecting the FFC | Epson C40UX specification

Stylus C40UX/C40SX/C20UX/C20SX

Revision A

8.Disconnect the FFC from the connector.

FFC

Figure 4-30. Disconnecting the FFC

If the Carriage unit is disassembled or replaced with a new one, make sure that the Carriage timing belt is set in the assembling groove correctly as following figure.

Timing belt

ADJUSTMENT When the Printhead is replaced with a new one, following REQUIRED adjustments must be performed in the order below: Refer to Table

5-1

1.Initial ink charge

2.Head ID input

3.Bi-D adjustment

When the Printhead is removed and reinstalled, only the following adjustment is required. Refer to Table 5-1

1.Head cleaning

2.Bi-D adjustment

Disassembly and Assembly

Disassembly

72

Image 72

Epson C40UX service manual Disconnecting the FFC

Contents

Stylus C40UX/C40SX/C20UX/C20SX General Notice Precautions About This Manual Revision Status Contents Adjustment Disassembly Product Description Delay of oparation Eeprom 29 H bit 0 value Model Delay time during printingDifferences between the Stylus C20 and the Stylus C40 Throughput Physical Specification Printing SpecificationHorizontal Printable area Available dot CR Speed Electrical specification Paper FeedingInput Data Buffer Feed condition Time Speed Safety Approvals Envirormental ConditionReliability Acoustic Noise Signal name In/Out Function description USB InterfaceParallel Interface Forward Channel Parallel I/F mode Typical time of tack Parameter Minimum MaximumParameter Pin No Signal Name ReturnG Functional description Parallel Interface Reverse Channel Prevention Hosts from Data Transfer Time-out IEEE1284.4 Protocol Operate Switch Control PanelPanel Functions Printer Condition and Panel Status Errors Printer Initialization Paper Specification Paper Handling Printing Area Printable Area for Cut Sheet Paper LMLeft RMRight TMTop Black BM Color BM MarginSize Black Ink Cartridge Color Ink Cartridge Operating Principles Overview Printer Mechanism Printhead Printhead Sectional Drawing Normal State Ejecting StateInk Path Ink Cavity Carriage Motor Specification Items SpecificationsCarriage Mechanism Detection position I/C change position PF Motor Specifications Paper Feeding Mechanism† PF motor drive transmission path † Switch the PF motor drive to ASF unit side Paper Loading Mechanism ASF Unit ASF unit function & PF Motor rotational direction † Transfer the PF motor drive to LD roller† Clutch Mechanism 11. Disengage & Clutch mechanism † Paper Return Plate Pad holder 13. ASF Paper Loading Sequence Ink System Mechanism PF motor rotational direction & Ink System Mechanism 16. Cap Mechanism Wiper with the cap unit Non porous pad in cap 18. non porous pad in cap Stylus C40/C20 † Manual Cleaning † Timer CleaningInk Sequence † Initial ink charge † Flashing Printing mode Printing mode for Color modePrinting mode for Black mode Electrical Circuit Operating Principles 1 C417 PSB/PSE boardApplication of the DC Voltages TRANST1 2 C413 MAIN/B Board Main Elements Troubleshooting Sensor Name Check Point Signal Level Switch Mode Sensor Check PointMotor Location Check Point Resistance Troubleshooting with LED Error Indications Error Indicator of Operation PanelError Condition and possible cause Printer Status Indicators Priority Power Error Paper out error indication Step Detail phenomenon Check point Remedy Spur gear 35.2 is Rotating If it is no problem, proceed Paper jam error indication 10. Paper jam error indication 11. Paper Jam Error indication12. Ink Out error indication Detail phenomenon Check point Remedy 15. Fatal Error indication 13. Multiple papers are always loaded14. Paper is always loaded without any print job 17. Dot missing occur and it is not recovered with CL 18. Dot missing occur and it is not recovered with CL 19. Dot missing occur and it is not recovered with CL 20. Print quality is not good 21. Print quality is not good 22. Print quality is not good Disassembly and Assembly Precautions Printer Et que le cordon d’alimentation soit debranche Name and Specification Outward Form ToolsScrews Name Supplier Parts No Work Completion Check Work Completion CheckClassifi Check Point Status Cation Classifi Check Point Status Disassembly Disassembling Flowchart Upper housing removal Upper housingEdge guide ASF unit removal CBP 3⋅ CBS P2 3⋅ „ Waste ink counter reset operation. Refer to Section Waste ink pad removalTube stopper Waste ink pad PS unit removal CN2 PS unit S 3⋅ P 3⋅„ Tightening Torque for screw +/-1 kgf.cm Paper eject roller removal ProtrusionCBS 3⋅ Front Frame Paper Eject roller Gear Switch cover Hooks Main board removalUSB Type CBS 3⋅ Parallel Type F.S-Tite 3⋅ 21. Disconnecting the connectors 22. Removing the Main board CR motor removal Printhead unit removal Carriage unitCarriage cover Printhead unit 30. Disconnecting the FFC LD unit removal LD unit Cables Printer mechanism removal Adjustment Required Adjustment Required AdjustmentPerformance Priority Adjustment Program Initial Setting menu Adjustment Program feature Basic adjustment itemsMain Menu Service Bi-d adjustment even if the paper is out in the ASF. When Feed command until the paper is set in the ASF Eeprom initial setting Head ID Read out the Head ID from the Eeprom 10. Choose the Bi-d adjustment Bi-D 13. Bi-d adjustment input menu USB ID 15. Choose the USB ID input menu Top margin 16. Choose the Top margin menu Head cleaning Initial ink chargeFor the initial ink charge operation is so large Refurbishment for DOA 21. Choose the Refurbishment for DOA menu Protection counter check Check the present counter value Clear the present counter value Excepting ESP Eepron check 26. Eeprom check function 29. Eeprom backup data Eeprom back up data 15 A4 pattern will print 31. A4 Check pattern 32. A4 Check pattern Maintenance Cleaning Service Maintenance † Head Cleaning† Maintenance Error Clear Lubrication Lubrication Type/Point Main frame Right side viewLubrication Type/Point Remarks 200mm Appendix Connector Summary Major Component Unit CN9-Printhead Pin Address Explanation Setting Eeprom Address MapEeprom Address Map Factory Appendix Eeprom Address Map 103 Appendix Eeprom Address Map 104 Bit7 Bit6 Name mode Market Eeprom address Eeprom settingBit3 Bit2 D4mode Bit1 Bit0 D4mode Component Layout C413MAIN component layout Appendix Component Layout 107 Parts List Parts listRef No Description Exploded Diagram Stylus C40UX/C40SX/C20UX/C20SX Exploded Diagram Appendix Exploded Diagram 110 Appendix Exploded Diagram 111 Stylus C40UX/C40SX/C20UX/C20SXRevision a Appendix Exploded Diagram 113 Appendix Exploded Diagram 114 Electrical Circuits Page Page Page Page