
Command | ASCII Command | Response | Additional Description |
| (host to scaler) | (scaler to host) |
|
|
|
|
|
|
|
|
|
Video effect |
|
|
|
Cut | E0SWEF} | Swef0] | Sets the switch to cut. |
Dissolve | E1SWEF} | Swef1] | Sets the switch to dissolve. |
View setting | ESWEF} | 0] (or 1]) | View setting (0 = cut, 1 = dissolve). |
|
|
|
|
Effect duration |
|
|
|
Set dissolve duration | EX3%EDUR} | EDURX3%] | Sets the effect duration to tenths of seconds |
|
|
| (range 2 = 0.2 to 50 = 05.0 seconds. Default |
|
|
| is 3 = 0.3 seconds). |
View duration | EEDUR} | X3%] | View effect duration. |
|
|
| |
Front panel security lockout (Executive Mode) |
|
| |
Enable Executive | 1X | Exe1] | Lock entire front panel. |
mode 1 |
|
|
|
Enable Executive | 2X | Exe2] | Limited front panel adjustments (input |
mode 2 |
|
| selection, PIP/Swap, and Auto- Image) can |
|
|
| be made. |
Disable Executive | 0X | Exe0] | Unlock front panel controls. All front panel |
mode |
|
| adjustments can be made. |
View Executive | X | 0] (or) 1] | View the current status: |
mode status |
| (or) 2] | 0 = off [default]; 1 = on, complete; |
|
|
| 2 = on, limited adjustments. |
Overscan mode (applies only to SMPTE [NTSC, PAL, 480p, 576p, 720p, 1080i, 1080p] input rates)
Set value | EX#*X2*OSCN} | OscnX#*X2*] | Set input format X# to overscan mode X2*. |
View status | EX#OSCN} | X2*] | Show overscan mode status for input |
|
|
| format X#. |
|
|
| |
HDCP notification (green screen/message) |
|
| |
Enable notification | EN1HDCP} | HdcpN1] | Enable the HDCP notification. |
Disable notification | EN0HDCP} | HdcpN0] | Disable the HDCP notification; instead |
|
|
| mute output. |
Query notification | ENHDCP} | X(] | Query the HDCP notification. |
HDCP status (valid for HDMI inputs and HDMI oututs only)
Query input | EIX!HDCP} | X3#] | Query the HDCP status of the current input |
|
|
| X!. |
|
| HdcpIX!*X3#] | Verbose mode response |
Query output | EOX@HDCP} | X3#] | Query the HDCP status of the HDMI output |
|
|
| X@. |
|
| HdcpOX@*X3#] | Verbose mode response |
NOTE: X! = Input selection: 1 to 5
X@ = Output selection: 0 = all outputs (default), 1 = analog (VGA, YUVp, HDTV), 2 = HDMI, 3 =
X# = Input video format: 0 = no signal detected, 1 = RGB, 2 = YUV auto, 3 = RGBcvS, 4 =
6 = DVI/HDMI (only available for inputs 3, 4, and 5), 7 = Autodetect (default for inputs 1 and 2)
X( = Enable/disable: 0 = off/disable, 1 = on/enable
X2* = Overscan (applied to SMPTE [NTSC/PAL - 480p
1 = 2.5% (default for YUV, RGBcvS,
X3# = HDCP status (valid only on HDMI/DVI outputs): 0 = no sink or source detected, 1 = sink or source detected with HDCP,
2 = sink or source detected but no HDCP is present
X3% = Effect duration: from 2 to 50, in 0.1 second steps (where 2 = 0.2 seconds, 50 = 5.0 seconds), default = 3 (0.3 seconds)
DVS 605 • SIS Communication and Control | 52 |