Manuals / Fujitsu / Computer Equipment / Server

Fujitsu TX300 manual Closing the server

Models: TX300

1 122

Download 122 pages 28.21 Kb

Page 110

Floorstand model

Completion

11.2.3 Closing the server

I The left side cover closes easily when the server is in the horizontal position.

ÊLay the server on its right side.

Ask a second person to help you do this.The server can weigh up to 25-40 kg depending on its configuration.

Ensure that the feet project over the edge of the table.

Figure 84: Closing the server

ÊPull the locking lever as far as it will go and insert the side cover (1).

ÊPush the side cover against the housing and at the same time push the locking lever shut (2).

This pushes the side cover forward and locks it in place.

ÊInsert the key.

ÊLock the server.

ÊConnect all power plugs to the power outlets.

ÊPress the On/Off button to start up the server.

110

Options Guide

TX300 S6

Image 110

Fujitsu TX300 manual Closing the server

Contents

Primergy TX300 S6 Server Certified documentation according to DIN EN ISO Comments… Suggestions… Corrections…Copyright and Trademarks Radio interference For your safetyHigh safety use Aluminum electrolytic capacitorsOnly for the Japanese market About Sata hard disk drives Measures against momentary voltage dropHarmonic Current Standards Only for the Japanese market Options Guide Contents Contents Multibay 1Completion 11.1 Installing the fan carrier Floorstand model Contents Preface Concept and target groups Preface Concept and target groupsDocumentation overview PrefaceDocumentation overview Further sources of informationExpansions and conversions Preface Accessible drivesExpansions and conversions Main memoryTrusted Platform Module TPM Battery Backup UnitAdditional expansion cards in the PCI Express slots USB Flash Module UFM Notational conventionsNotational conventions Preface Conversion from a floorstand model to a rack modelProcedure Procedure Options Guide Safety instructions Installation and operation Before starting upVcaution Vcaution Batteries Working with CDs/DVDs/BDs and optical drivesTX300 S6 Laser information ESD labelTX300 S6 Preparation Floorstand model Preparation Floorstand modelOpening the server Removing the front cover Removing the drive cover and the HDD coverPull out the two green locking buttons Removing the server feet Removing the server feetPulling the server out of the rack and opening the server Rack modelRack model Preparation Removing the server from the rack and opening the server Unlocking the server and lifting it out of the railsRemoving the rack front cover Removing the rack front coverDisconnecting the power cable Removing the fan carrierRemoving the fan carrier Preparation Removing the fan carrierMain memory Memory modules Memory modulesMemory modules Expanding the main memory Expanding the main memoryProcessors Installing a second processor Installing a second processorProcessors Opening the processor holder and removing the socket coverInserting and locking the processor Removing the protective cover Mounting and locking the heat sink Replacing the processor Removing the heat sinkReplacing the processor Removing an old processorInserting and locking a new processor Inserting and locking a new processorApplying and distributing thermal paste Mounting and locking the heat sink Replacing the heat sink Replacing the heat sinkAccessible drives and LSD/LSP Equipping of the bays Equipping of the baysAccessible drives and LSD/LSP Removing the dummy cover Accessible 5.25-inch driveAccessible 5.25-inch drive Accessible drives and LSD/LSP Detaching the EasyClick rails from the dummy coverInstalling an accessible 5.25-inch drive Attaching the EasyClick rails example DVD driveEquipping Multibay Installing LSP or LSDMultibay Multibay Sliding the LSP in the 3.5-inch frameInstalling a slimline DVD drive Fastening the 3.5-inch frame with LSP in MultibayConnecting the PS adapter cable to the DVD drive Inserting the DVD drive module in the Multibay Installing Multibay Connecting the Sata cable to the DVD driveInstalling Multibay Connecting the PS adapter cable to the power cable Connecting the I2C cable to the LSP/LSD HDD extension box HDD extension boxMultibay Installing Multibay Connecting cables to HDD backplane of MultibayCabling SAS cable 2 2.5-inch HDD extension box Attaching EasyClick rails to 2.5-inch HDD extension boxInstalling 2.5 inch HDD extension box Connecting PS adapter cable to HDD backplanesCabling 2.5-inch HDD extension box Expansion cards and BBU Slot Description Installing expansion cardsInstalling expansion cards Expansion cards and BBU Removing the slot coverInstalling an expansion card Installing a BBU Removing the BBU carrier plateInstalling a BBU Position of used holes on the BBU carrier plateFastening BBUs onto the BBU carrier plate Connecting the cable to the BBU Inserting the BBU carrier plate Fastening the BBU carrier plate Opening the cable cover Routing the first and second BBU cable Removing the voltage converter holder Threading the third BBU cable through the cable opening Reinserting the voltage converter holder Securing the voltage converter holder Inserting and fastening the cable cover Installing a BBU Further options TPMTPM Further options Securing the TPMUFM installation kit USB Flash Module UFMUSB Flash Module UFM USB Flash Module UFM Conversion from a floorstand model to a rack model Removing the right-hand side coverRemoving the foot mounting rail Options Guide 101 Inserting the rail adapter shown rail adapter left Fasten the two screws of the rail adapter Conversion from a floorstand model to a rack model Installing the fan carrier CompletionInstalling the fan carrier Connecting the power cableMounting the server feet CompletionAttaching the front cover Floorstand modelOptions Guide 109 Closing the server Closing the serverAttaching the rack front cover Attaching the rack front coverRack model Inserting the server aOptions Guide 113 114 Options Guide Appendix Cabling116 Options Guide Options Guide 117 Cabling118 Options Guide Options Guide 119 120 Options Guide Index BBUIndex 111