Rack model, Inserting the server a | Fujitsu TX300 specification

Rack model

Completion

11.3.2 Closing the server

ÊPull the locking lever as far as it will go and insert the top cover (see also figure 84 on page 110).

ÊPush the top cover against the housing and push down the locking lever at the same time.

Closing the locking lever pushes the top cover forward and the hooks on the right edge of the top cover engage.

If you have not removed the server from the rack cabinet, please skip steps 1-4.

V CAUTION!

At least two people are required to install the server in the rack cabinet.

Do not use the handles on the rack front cover to lift the server into the rack.

Figure 86: Inserting the server (a)

112

Options Guide

TX300 S6

Image 112

Fujitsu TX300 manual Rack model, Inserting the server a

Contents

Primergy TX300 S6 Server Copyright and Trademarks Comments… Suggestions… Corrections…Certified documentation according to DIN EN ISO For your safety High safety useRadio interference Aluminum electrolytic capacitors Harmonic Current Standards Measures against momentary voltage dropOnly for the Japanese market About Sata hard disk drives Only for the Japanese market Options Guide Contents Contents Multibay 1 Completion 11.1 Installing the fan carrier Floorstand model Contents Preface Documentation overview Concept and target groupsConcept and target groups Preface PrefaceDocumentation overview Further sources of information Accessible drives Expansions and conversionsExpansions and conversions Preface Main memory Additional expansion cards in the PCI Express slots Battery Backup UnitTrusted Platform Module TPM Notational conventions Notational conventions PrefaceUSB Flash Module UFM Conversion from a floorstand model to a rack model Procedure Procedure Options Guide Safety instructions Installation and operation Before starting up Vcaution Vcaution Batteries Working with CDs/DVDs/BDs and optical drives TX300 S6 Laser information ESD label TX300 S6 Preparation Opening the server Floorstand modelFloorstand model Preparation Removing the front cover Removing the drive cover and the HDD cover Pull out the two green locking buttons Removing the server feet Removing the server feet Rack model Preparation Rack modelPulling the server out of the rack and opening the server Removing the server from the rack and opening the server Unlocking the server and lifting it out of the rails Removing the rack front cover Removing the rack front cover Disconnecting the power cable Removing the fan carrier Removing the fan carrier Preparation Removing the fan carrier Main memory Memory modules Memory modules Memory modules Expanding the main memory Expanding the main memory Processors Installing a second processor Installing a second processor Processors Opening the processor holder and removing the socket cover Inserting and locking the processor Removing the protective cover Mounting and locking the heat sink Replacing the processor Removing the heat sink Replacing the processor Removing an old processor Inserting and locking a new processor Inserting and locking a new processor Applying and distributing thermal paste Mounting and locking the heat sink Replacing the heat sink Replacing the heat sink Accessible drives and LSD/LSP Equipping of the bays Equipping of the bays Accessible drives and LSD/LSP Accessible 5.25-inch drive Accessible 5.25-inch driveRemoving the dummy cover Accessible drives and LSD/LSP Detaching the EasyClick rails from the dummy cover Installing an accessible 5.25-inch drive Attaching the EasyClick rails example DVD drive Multibay Installing LSP or LSDEquipping Multibay Multibay Sliding the LSP in the 3.5-inch frame Installing a slimline DVD drive Fastening the 3.5-inch frame with LSP in Multibay Connecting the PS adapter cable to the DVD drive Inserting the DVD drive module in the Multibay Installing Multibay Connecting the Sata cable to the DVD drive Installing Multibay Connecting the PS adapter cable to the power cable Connecting the I2C cable to the LSP/LSD HDD extension box HDD extension box Multibay Installing Multibay Connecting cables to HDD backplane of Multibay Cabling SAS cable 2 2.5-inch HDD extension box Attaching EasyClick rails to 2.5-inch HDD extension box Installing 2.5 inch HDD extension box Connecting PS adapter cable to HDD backplanes Cabling 2.5-inch HDD extension box Expansion cards and BBU Installing expansion cards Installing expansion cardsSlot Description Expansion cards and BBU Removing the slot cover Installing an expansion card Installing a BBU Removing the BBU carrier plate Installing a BBU Position of used holes on the BBU carrier plate Fastening BBUs onto the BBU carrier plate Connecting the cable to the BBU Inserting the BBU carrier plate Fastening the BBU carrier plate Opening the cable cover Routing the first and second BBU cable Removing the voltage converter holder Threading the third BBU cable through the cable opening Reinserting the voltage converter holder Securing the voltage converter holder Inserting and fastening the cable cover Installing a BBU Further options TPM TPM Further options Securing the TPM UFM installation kit USB Flash Module UFM USB Flash Module UFM USB Flash Module UFM Conversion from a floorstand model to a rack model Removing the right-hand side cover Removing the foot mounting rail Options Guide 101 Inserting the rail adapter shown rail adapter left Fasten the two screws of the rail adapter Conversion from a floorstand model to a rack model Installing the fan carrier Completion Installing the fan carrier Connecting the power cable Mounting the server feet Completion Attaching the front cover Floorstand model Options Guide 109 Closing the server Closing the server Attaching the rack front cover Attaching the rack front cover Rack model Inserting the server a Options Guide 113 114 Options Guide Appendix Cabling 116 Options Guide Options Guide 117 Cabling 118 Options Guide Options Guide 119 120 Options Guide Index BBU Index 111