Installing a second processor | Fujitsu TX300 specification

Installing a second processor

Processors

6.1Installing a second processor

The system board can be upgraded with a second processor. The upgrade kit consists of a processor and a heat sink.

V CAUTION!

Only processors of the same type may be used on the system board. That means the number of the internal processor cores as well as the primary clock and the FSB frequency have to be the same. For dual operation, use a suitable multiprocessor operating system.

ÊOpen the server and remove the fan carrier as described in the chapter "Preparation" on page 27.

Figure 15: Opening the heat sink retaining clips

ÊPress the heat sink retaining clips downward and inward to release them.

ÊFold the heat sink retaining clips back.

42

Options Guide

TX300 S6

Image 42

Fujitsu TX300 manual Installing a second processor

Contents

Primergy TX300 S6 Server Comments… Suggestions… Corrections… Copyright and TrademarksCertified documentation according to DIN EN ISO Radio interference For your safetyHigh safety use Aluminum electrolytic capacitors Measures against momentary voltage drop Harmonic Current StandardsOnly for the Japanese market About Sata hard disk drives Only for the Japanese market Options Guide Contents Contents Multibay 1 Completion 11.1 Installing the fan carrier Floorstand model Contents Preface Concept and target groups Documentation overviewConcept and target groups Preface PrefaceDocumentation overview Further sources of information Expansions and conversions Preface Accessible drivesExpansions and conversions Main memory Battery Backup Unit Additional expansion cards in the PCI Express slotsTrusted Platform Module TPM USB Flash Module UFM Notational conventionsNotational conventions Preface Conversion from a floorstand model to a rack model Procedure Procedure Options Guide Safety instructions Installation and operation Before starting up Vcaution Vcaution Batteries Working with CDs/DVDs/BDs and optical drives TX300 S6 Laser information ESD label TX300 S6 Preparation Floorstand model Opening the serverFloorstand model Preparation Removing the front cover Removing the drive cover and the HDD cover Pull out the two green locking buttons Removing the server feet Removing the server feet Rack model Rack model PreparationPulling the server out of the rack and opening the server Removing the server from the rack and opening the server Unlocking the server and lifting it out of the rails Removing the rack front cover Removing the rack front cover Disconnecting the power cable Removing the fan carrier Removing the fan carrier Preparation Removing the fan carrier Main memory Memory modules Memory modules Memory modules Expanding the main memory Expanding the main memory Processors Installing a second processor Installing a second processor Processors Opening the processor holder and removing the socket cover Inserting and locking the processor Removing the protective cover Mounting and locking the heat sink Replacing the processor Removing the heat sink Replacing the processor Removing an old processor Inserting and locking a new processor Inserting and locking a new processor Applying and distributing thermal paste Mounting and locking the heat sink Replacing the heat sink Replacing the heat sink Accessible drives and LSD/LSP Equipping of the bays Equipping of the bays Accessible drives and LSD/LSP Accessible 5.25-inch drive Accessible 5.25-inch driveRemoving the dummy cover Accessible drives and LSD/LSP Detaching the EasyClick rails from the dummy cover Installing an accessible 5.25-inch drive Attaching the EasyClick rails example DVD drive Installing LSP or LSD MultibayEquipping Multibay Multibay Sliding the LSP in the 3.5-inch frame Installing a slimline DVD drive Fastening the 3.5-inch frame with LSP in Multibay Connecting the PS adapter cable to the DVD drive Inserting the DVD drive module in the Multibay Installing Multibay Connecting the Sata cable to the DVD drive Installing Multibay Connecting the PS adapter cable to the power cable Connecting the I2C cable to the LSP/LSD HDD extension box HDD extension box Multibay Installing Multibay Connecting cables to HDD backplane of Multibay Cabling SAS cable 2 2.5-inch HDD extension box Attaching EasyClick rails to 2.5-inch HDD extension box Installing 2.5 inch HDD extension box Connecting PS adapter cable to HDD backplanes Cabling 2.5-inch HDD extension box Expansion cards and BBU Installing expansion cards Installing expansion cardsSlot Description Expansion cards and BBU Removing the slot cover Installing an expansion card Installing a BBU Removing the BBU carrier plate Installing a BBU Position of used holes on the BBU carrier plate Fastening BBUs onto the BBU carrier plate Connecting the cable to the BBU Inserting the BBU carrier plate Fastening the BBU carrier plate Opening the cable cover Routing the first and second BBU cable Removing the voltage converter holder Threading the third BBU cable through the cable opening Reinserting the voltage converter holder Securing the voltage converter holder Inserting and fastening the cable cover Installing a BBU Further options TPM TPM Further options Securing the TPM UFM installation kit USB Flash Module UFM USB Flash Module UFM USB Flash Module UFM Conversion from a floorstand model to a rack model Removing the right-hand side cover Removing the foot mounting rail Options Guide 101 Inserting the rail adapter shown rail adapter left Fasten the two screws of the rail adapter Conversion from a floorstand model to a rack model Installing the fan carrier Completion Installing the fan carrier Connecting the power cable Mounting the server feet Completion Attaching the front cover Floorstand model Options Guide 109 Closing the server Closing the server Attaching the rack front cover Attaching the rack front cover Rack model Inserting the server a Options Guide 113 114 Options Guide Appendix Cabling 116 Options Guide Options Guide 117 Cabling 118 Options Guide Options Guide 119 120 Options Guide Index BBU Index 111