ML1200rstp##port port=1 status=disable | GE manual

RAPID SPANNING TREE PROTOCOL

CHAPTER 13: RAPID SPANNING TREE PROTOCOL

Configuring RSTP (continued)

ML1200(rstp)##show stp ports

RSTP Port Configuration

-------------------------------------------------------------------------------

Port# Type Priority Path Cost State Des. BridgeDes. Port

-------------------------------------------------------------------------------

01	TP(10/100)	128	2000000	Forwarding	80:00:00:20:06:2b:e1:55	00:01
02	TP(10/100)	100	250000	Forwarding	80:00:00:20:06:2b:e1:55	00:02
03	100MB Fiber	128	200000	Disabled		00:03
04	100MB Fiber	128	200000	Disabled		00:04
05	100MB Fiber	128	200000	Disabled		00:05
06	100MB Fiber	128	200000	Disabled		00:06
07	TP(10/100)	128	2000000	Disabled		00:07

ML1200(rstp)##port port=1 status=disable

ML1200(rstp)##show stp ports

RSTP Port Configuration

-------------------------------------------------------------------------------

Port# Type Priority Path Cost State Des. BridgeDes. Port

-------------------------------------------------------------------------------

01	TP(10/100)	128	2000000	NO STP	00:01
02	TP(10/100)	100	250000	Forwarding 80:00:00:20:06:2b:e1:55		00:02
03	100MB Fiber	128	200000	Disabled		00:03
04	100MB Fiber	128	200000	Disabled		00:04
05	100MB Fiber	128	200000	Disabled		00:05
06	100MB Fiber	128	200000	Disabled		00:06
07	TP(10/100)	128	2000000	Disabled		00:07

ML1200(rstp)##port port=1 status=enable

ML1200(rstp)##show stp ports

RSTP Port Configuration

-------------------------------------------------------------------------------

Port# Type Priority Path Cost State Des. BridgeDes. Port

-------------------------------------------------------------------------------

01	TP(10/100)	128	2000000	Forwarding	80:00:00:20:06:2b:e1:55	00:01
02	TP(10/100)	100	250000	Forwarding	80:00:00:20:06:2b:e1:55	00:02

13–12

MULTILINK ML1200 MANAGED FIELD SWITCH – INSTRUCTION MANUAL

Image 220

GE instruction manual ML1200rstp##port port=1 status=disable

Contents

MultiLink ML1200 Managed Field Switch GE Multilin Electrical Safety requirements Canadian Emissions Statement Table of Contents Access 10-3 10-110-5 10-7 10-1210-13 10-19 14-9 15-115-4 15-5 17-14 17-1618-1 18-3 Getting Started Multilink ML1200 Managed Field Switch IntroductionInspecting the Package and Product Order Codes ML1200 Specifications Performance Alarm Relay Contacts Interrupts Sinusoidal Vibration DNV To 4 G Applicable Council Directive According to CE Compliance Low voltage directive EN60950-1 EMC DirectiveNorth America CULus UL60950-1 C22.2 No ISO9001 Console Setup Command Line Interface FirmwareConsole Connection Console Screen Automatic IP Address ConfigurationLogging In for the First Time Setting the IP Parameters Using Console Port Step Ipconfig ip=ip-address mask=subnet-mask dgw=gateway ML1200# rebootAn example is shown below ML1200# save Enable user-name Privilege Levels User Management Help command string Command EnterCommand string TAB First character of the command TAB Help Following example, the TAB key completes the command ExitingLogout Following example illustrates logging out from a session Secure site will issue the certificate check shown below EnerVista Secure Web ManagementMake sure you use Https secure Http and not Http in the URL Example shown in the previous section, the URL is Login screen Select the Administration User Mgmt User Accounts menu item To add a user, use the add button Introduction Introduction Introduction Modifying the Privilege Level To exit or logout, click on the logout button Confirm the logout by selecting OK in the pop-up window ML1200 Firmware Updates Updating through the Command LineUpdating Multilink ML1200 Firmware Selecting the Proper Version ML1200# xmodem get type=app Https//IP address of the switch Introduction Introduction Multilink ML1200 Managed Field Switch Product Description Overview Product Description Product Description PoE power pass-through, C2 Module MDIX, 10/100Mb 4-port Four-Port Copper Module, C1 Module Mdix Two-Port Fiber Modules, 2@ 100Mb fiber Two -Port 10 Mb mm Fiber ST Modules SFP Gigabit 1000Mbps port modules Packet Prioritization, 802.1p QOS Frame Buffering and Flow Control Managed Network Firmware for Multilink ML1200-Series Features and Benefits Managed switching for high performance Ethernet LANsFeatures Fiber-Built-In Management Software included Product Description Applications Example Example Locating Multilink ML1200 Switches Multilink ML1200 Managed Field Switch InstallationPreparation Fiber Connecting Ethernet MediaCopper Twisted Pair CAT 3, 4 Twisted Pair CAT Gigabit SFP Small Form-factor Pluggable Optical Transceivers HE HJ Module H7 Module H8 HD ModuleHK Module Mechanical Installation DIN-Rail Mounting the Multilink ML1200 Installation Electrical Installation Powering the Multilink ML1200 Managed Field Switch 3 ML1200 Port Module PM Installation Pinout information for above connector Request to SendTransceiver Data Ground Switching Functionality Multilink ML1200 Managed Field Switch OperationFunctionality Auto-Cross Mdix and Auto-negotiation, for RJ-45 ports Status LEDsFor Multilink ML1200 models /ML1200 Flow-control, Ieee 802.3x standard Power Budget Calculations for ML1200 PM’s with Fiber Media Typical H4, HH Mb FX Multilink ML1200 Managed Field Switch Port Modules 2 ML1200 Modules 2.2 C7 Module, 2@10Mb multi-mode FX-ST twist lock Module CB Module, 2 Ports @100Mbps single-mode FX-SC-type, Sgl.M CC Module, 4 @100Mb multi-mode FX , Mtrj Small-Form-factor 2.10 C1 Module Twisted Pair, 10/100Mb, 4-Port PoE LEDs Summary SFPs, Gigabit 1000Mbps port modules Before Calling for Assistance Operation IP Address and System Information Multilink ML1200 Managed Field Switch IP AddressingOverview Edit the IP address information Dhcp and bootp Bootp DatabaseConfiguring DHCP/bootp/Manual/AUTO Importance of an IP Address Select the Administration System menu item Click Edit Using Telnet Telnet enabledisableML1200access## telnet enable ML1200access## exit ML1200# Select the Administration Telnet menu item Default port for telnet isTelnet ipaddress port=port number Show session Kill session id=session For example ML1200# show session Setting Serial Port Parameters Setting ParametersSystem Parameters Date and Time SnmpSetvar sysnamesyscontactsyslocation =string Set timezone GMT=+ or hour=0-14 min=0-59 Syntax for other date and time commands are Following command sequence sets the daylight locationNetwork Time Set timeformat format=1224 ML1200# sntp ML1200sntp## sync hour=5 ML1200sntp## sntp enableML1200sntp## exit IP Addressing IP Addressing Saving and Loading Command Line System ConfigurationConfig file # Restricted Rights System Displaying configuration Syntax show config module=module-nameWhere module-name can be Names, passwords ’show config’ command output More ML1200# show config module=snmp Hardware Select Y. The ML1200 will prompt Saving ConfigurationSelect N Show host command displays the host table entries Save format=v2v3 Script File # Restricted Rights Saving and Loading EnerVista Software IP Addressing Host Names IP Addressing Erasing Configuration Kill Config option using SWM IP Addressing STP, Rstp settings Port/Tag Vlan settingsIP-Access and Host Table settings Lacp settings ML1200# kill config Introduction to IPv6 IPv6What’s changed in IPV6? 3 IPv6 Addressing Configuring IPv6 Syntax ping6 IPv6 address pings an IPv6 stationSyntax show ipv6 displays the IPv6 information Syntax ftp IPv6 address ftp to an IPv6 station List of commands in this chapter Syntax telnet IPv6 address telnet to an IPv6 station Multilink ML1200 Managed Field Switch Access Considerations Securing AccessPasswords Description Port Security Feature Commands For example, using the configure port-securitycommandLearn port=number-list enabledisable show port-security Ps enabledisable ML1200port-security## ps enable ML1200port-security## ps disableAllowing MAC Addresses ML1200port-security## allow Example 6-1 Viewing the port security settings ML1200port-security## learn port=3 enableTo deny a mac address, use the following Example 6-2 Enabling learning on a port ML1200port-security## signal port=3 logandtrap Save the port-security configuration use the save commandExample 6-4 Removing MAC addresses from specific ports Access Considerations Example 6-5 Configuring port security Security Logs Set logsize size=1-1000 Example 6-6 Security log commandsML1200# show log Access Show ip-accessAuthorized Managers Removeall ML1200access## exit ML1200# accessExample 6-7 Allowing/blocking specific IP addresses Configuring Port Security with EnerVista Software After enabling the EnerVista Secure Web Management software Access Considerations Access Considerations Logs Authorized Managers Access Considerations Access Considerations Introduction to Multilink ML1200 Managed Field Switch Access Using Radius2 802.1x Protocol 802.1x network components 802.1x authentication details Configuring 802.1x through the Command Line Interface Show auth configportsAuth enabledisable Auth Show-stats port=num Show-statscommand displays 802.1x related statisticsTrigger-reauthport=numlistrange Example Example 7-1 Setting port control parametersOn following Setting port control parameters ML1200auth## show-port backend ML1200auth## shoW-port reauth ML1200auth## Commands To edit the port settings, click on the edit icon Select the Configuration Radius Port Access menu item Access Using Radius Access Using Radius After all the port characteristics are enabled Multilink ML1200 Managed Field Switch Access using TACACS+ Introduction to TACACS+ TACACS+ Flow TACACS+ Packet Packet type Possible values are Tacacs packet format Configuring TACACS+ through the Command Line Interface Tacplus enabledisableExample 8-1 below, illustrates how to configure TACACS+ Show tacplus statusservers ML1200user## tacplus enable Example 8-1 Configuring TACACS+ML1200user## tacplus disable Access Using TACACS+ Access Using TACACS+ Access Using TACACS+ Multilink ML1200 Managed Field Switch Port Mirroring Setup Port Mirroring Port Mirroring using the Command Line Interface Prtmr enabledisableShow port-mirror Port-mirror Port Setup Device command enters the device configuration modeSetport command configures the port characteristics Device Example 9-1 Port setup ML1200# deviceML1200device## show port ML1200device## exit ML1200# Where the rxthreshold value can be from 4 to 30 default is Flow ControlBack Pressure Flowcontrol xonlimit=value xofflimit=value Back pressure and flow control ML1200device## show port=11 Broadcast Storms Rate-thresholdport=portlistrange rate=frames/sec Broadcast-protect enabledisableShow broadcast-protect Link Loss Alert Example 9-3 Preventing broadcast storms Example 9-4 Link loss alert ML1200device## show port=3 Select the Configuration Port Mirroring menu item Port Setup Port Mirroring and Setup Port Mirroring and Setup Broadcast Storm menu Port Mirroring and Setup Multilink ML1200 Managed Field Switch Vlan Vlan Description Vlan Multilink ML1200 supports up to 32 VLANs per switch Tag Vlan vs. Port Vlan 10-4 Set vlan type=porttagnone Configuring Port VLANs through the Command Line InterfaceAdd id=vlan Id name=vlan name port=numberlistrange Start vlan=namenumberlistrange SaveEdit id=vlan Id name=vlan name port=numberlistrange Show vlan type=porttag id=vlanid Vlan VID=1 Select the Configuration Vlan Port-Based menu item Currently assigned Port VLANs are displayed as follows 10-9 10-10 10-11 Configuring Tag VLANs through the Command Line Interface Show-port port=portlistrange 10-13 Example 10-1 Converting Port Vlan to Tag Vlan Converting Port Vlan to Tag Vlan ML1200tag-vlan##add id=20 name=marketing port=3-5 ML1200tag-vlan##set-port port=3-5 filter status=enable Name engineering Status Active Port Mode Status Tagged 10-19 Click On Configuration vlan tag-based Menu Next step is to define the VLANs needed. To do that 10-21 Select the Configuration Vlan Tag-Based Tagging menu 10-23 10-24 Vlan Registration over Garp Gvrp Concepts Gvrp Operations Vlan Registration Over Garp Vlan assignment in Gvrp enabled switches Show-vlan Port settings for Gvrp operationsStatic vlan=VID Gvrp options Example 11-1 Converting a dynamic Vlan to a static VlanML1200# gvrp ML1200gvrp## show-vlan ML1200gvrp## static vlan=10 ML1200gvrp## show-vlan 11-6 Configuring Gvrp through the Command Line Interface Gvrp Operation NotesShow gvrp Show-forbid Example 11-2 Configuring Gvrp Select the Configuration Vlan Gvrp menu item To configure GvrpGvrp options on 11-10 Features and Operation STP default values Spanning Tree Protocol STP Configuring STP Show stp configports Example 12-1 Viewing STP configuration Example 12-2 Viewing STP ports Stp enabledisable StpSet stp type=stprstp Show active-stp Example 12-3shows how to enable STP using the above commands Example 12-3 Enabling STP Timers forward-delay=4-30 hello=1-10 age=6-40 Example 12-4 Configuring STP parameters ML1200stp##show stp ports Configuring STP parameters ML1200stp##cost port=2 value=20 ML1200stp##port port=1 status=enable Designated Root Priority 15535 Rstp concepts Transition from STP to Rstp Rapid Spanning Tree Protocol 13-3 Configuring Rstp through the Command Line Interface Rstp enabledisableNormal Rstp Rstp 13-5 Example 13-2 Reviewing the Rstp port parameters Forceversion stprstp Path cost as defined in Ieee 802.1d / 802.1wShow-forceversion Show-timers Port port=numberlistrange status=enabledisable Example 13-4 Configuring Rstp ML1200rstp##show stp config Configuring Rstp ML1200rstp##priority port=2 value=100 ML1200rstp##port port=1 status=disable Syntax for the romode command on Rstp is shown below Romode add port=portlistrange romode del port=portlistrange Example 13-5 Configuring smart RSTP, ring-only mode ML1200rstp##romode add port=1,2 13-15 Status Indicates whether STP or Rstp is enabled 13-17 Path cost defined in Ieee 802.1d and 802.1w 13-19 Click the Edit button to configure Rstp Then Save Enable Status 13-22 QoS Overview Multilink ML1200 Managed Field Switch Quality of ServiceQoS Concepts DiffServ and QoS IP Precedence IP Precedence ToS Field in an IP Packet Header Configuring QoS through the Command Line Interface Set-weightweight=0-7Show-portweight Qos Port weight settings Show qos command displays the QoS settingsShow qos type=porttagtos port=portlistrange Set-untagport=portlistrange priority=highlow tag=0-7 Following example shows how to configure QoS Example 14-1 Configuring QoS Configuring QoS ML1200qos##set-weight weight=4 ML1200qos##show-portweight 14-9 14-10 14-11 14-12 Multilink ML1200 Managed Field Switch Igmp Igmp Concepts Igmp Figure below shows a network running Igmp IP Multicast Filters Isolating multicast traffic in a network Reserved Addresses Excluded from IP Multicast Igmp Filtering Igmp Support Configuring Igmp through the Command Line Interface Igmp enable/disableShow igmp command displays the Igmp status Igmp Show-port Show-groupShow-router Following example shows how to configure Igmp Example 15-1 Configuring IgmpML1200igmp## show-port ML1200igmp## show-router Configuring Igmp ML1200igmp## mcast disable ML1200igmp## mcast enable 15-11 15-12 Multilink ML1200 Managed Field Switch Snmp Snmp Concepts Snmp Traps StandardsEnterprise Traps Intruder SNMPv1 standards RFC 2271-2275 SNMPv3 Configuring Snmp through the Command Line Interface Following example shows how to configure Snmp Show-trap id=id#Show-group id=id Show-view id=id Example 16-1 Configuring Snmp Configuring Snmp ML1200snmpv3## show-group ML1200snmpv3## show-group id=1ML1200snmpv3## show-view ML1200snmpv3## show-view id=1 ML1200snmpv3## show-access ML1200snmpv3## show-access id=1ML1200snmpv3## show-user ML1200snmpv3## show-user id=2 16-11 Multiple managers can be added as shown below 16-13 16-14 Configuring Rmon Rmon ML1200rmon## show rmon event ML1200rmon## exit ML1200# Multilink ML1200 Managed Field Switch Miscellaneous Mail Show smtp configrecipients Smtp enabledisableSmtp Delete id=1-5 Server command configures the global Smtp server settingsServer ip=ip-addr port=1-65535 retry=0-3 domain=domain ML1200smtp##show smtp config Statistics Following figure displays the port statistics for group Serial Connectivity Optimizing serial connection in HyperTerminal Show history HistoryShow version Ping Ping through the Command Line InterfacePing through EnerVista Secure Web Management software Prompt Changing the Command Line PromptSet prompt prompt string Command Line Interface Example System EventsFollowing example illustrates a typical event log Example 17-2 Typical system event log Select the Configuration Statistics Log Statistics menu item EnerVista Example 17-13 Command Reference Main Commands Set password sets the current user password Set commands are listed belowSet timeout sets the system inactivity time out Configuration commands Snmp enables or disables SnmpAlarm commands are shown below Authorization commands are shown below Device commands are shown below Vlan Registration over Garp for details Setqos configures QOS configuration usage Rapid Spanning Tree Protocol for additional details Passwd change the user password Spanning Tree Protocol STP for additional details 17-20 Multilink ML1200 Managed Field Switch Modbus Protocol Modbus ConfigurationCommand Line Interface Settings Following command-line interface settings are available ML1200access## show modbus ML1200# access ML1200access## modbus enableML1200access## modbus port=602 EnerVista Settings Select the Configuration Access Modbus menu item Modbus Memory Map Memory MappingModbus memory map Sheet 1 Modbus memory map Sheet 2 Modbus memory map Sheet 3 Modbus memory map Sheet 4 Modbus memory map Sheet 5 Modbus memory map Sheet 6 Modbus memory map Sheet 7 Modbus memory map Sheet 8 Modbus memory map Sheet 9 Modbus memory map Sheet 10 Modbus memory map Sheet 11 Modbus memory map Sheet 12 Modbus memory map Sheet 13 Modbus memory map Sheet 14 Modbus memory map Sheet 15 Modbus memory map Sheet 16 Modbus memory map Sheet 17 Modbus memory map Sheet 18 Modbus memory map Sheet 19 Modbus memory map Sheet 20 Modbus memory map Sheet 21 Modbus memory map Sheet 22 Modbus memory map Sheet 23 Modbus memory map Sheet 24 Modbus memory map Sheet 25 Modbus memory map Sheet 26 Modbus memory map Sheet 27 Modbus memory map Sheet 28 Modbus memory map Sheet 29 Modbus memory map Sheet 30 Modbus memory map Sheet 31 Modbus memory map Sheet 32 Modbus memory map Sheet 33 Format Codes 18-38 Multilink ML1200 Managed Field Switch Appendix a Revision HistoryChange Notes Changes to the Manual Warranty GE Multilin Warranty Statement Multilin Power Consumption 48 V DC, 24 V DC and 125 V DC Power, Theory of Operation Applications for DC Powered Ethernet Switches ML1200, -48 V, 24 V, 125 V DC Installation UL Requirements for DC-powered units Operation DC Power Input Appendix C Internal DC Dual- Source Power Input Specifications for Multilink ML1200 Field Switch Power Supply Internal, -48VDC Dual-Source Chapter C Internal DC DUAL-SOURCE Power Input Option Dual-Source Option Theory of Operation Features and Benefits of the Dual-Source Design Installation