HUAWEI MG323 GSM M2M Module

 

AT Command Interface Specification

Commands for Status Control

<indDescr>: string; Table 3-2 describes the values of the parameter.

Table 3-2Values of the <indDescr> and <indValue> parameters

 

 

<indDescr>

 

 

<indValue>

 

 

 

 

 

 

 

 

 

 

“battchg”: battery power level

 

0: has not been connected to any charger.

 

 

 

indicator. Currently, only the

 

 

 

 

 

 

1: has been connected to a charger.

 

 

 

value 5 is supported.

 

 

 

 

 

 

 

2: being charged.

 

 

 

 

 

 

 

 

 

 

 

 

 

3: The charge process is complete.

 

 

 

 

 

 

 

 

 

 

 

 

 

4: The charge process is interrupted due to an

 

 

 

 

 

 

error.

 

 

 

 

 

 

 

 

 

 

 

 

 

5: unknown.

 

 

 

 

 

 

 

 

 

“signal”: receive signal bit error

 

0: ≤ -113 dBm

 

 

 

rate indicator. Currently, only the

 

 

 

 

 

 

1: -111 dBm

 

 

 

value 99 is supported.

 

 

 

 

 

 

 

2–30: -109 dBm to -53 dBm

 

 

 

 

 

 

 

 

 

 

 

 

 

31: ≥ -51 dBm

 

 

 

 

 

 

 

 

 

 

 

 

 

99: unknown.

 

 

 

 

 

 

 

 

 

“service”: network service status

 

0: has not been registered with any network.

 

 

 

indicator.

 

 

 

 

 

 

 

 

1: has been registered with the home network.

 

 

 

 

 

 

 

 

 

 

 

 

When “roam=1, the MT has been registered with

 

 

 

 

 

another network.

 

 

 

 

 

 

 

 

 

“sounder”: audio status indicator,

 

0: without ring.

 

 

 

which indicates an event with

 

 

 

 

 

 

1: with ring.

 

 

 

ring. Currently, only the value 0

 

 

 

 

is supported.

 

 

 

 

 

 

 

 

 

 

 

 

“message”: unread short

 

0: without unread short message.

 

 

 

message indicator.

 

 

 

 

 

 

1: with unread short message.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

“call”: conversation status

 

0: without conversation.

 

 

 

indicator.

 

 

 

 

 

 

 

 

1: ongoing conversation or conversation hold.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

“roam”: roaming indicator.

 

0: registers with the home network or does not

 

 

 

 

 

 

register with any network.

 

 

 

 

 

 

 

 

 

 

 

 

 

1: registers with the roaming network.

 

 

 

 

 

 

 

 

 

“smsfull”: short message storage

 

0: The short message storage media is not full.

 

 

 

full indicator.

 

 

 

 

 

 

 

 

1: The short message storage media is full.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

“rssi”: receive signal strength

 

0: ≤ -112 dBm

 

 

 

indicator.

 

 

 

 

 

 

 

 

1–4: The strength interval is 15 dBm.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

5: ≥ -51 dBm

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Issue 02 (2010-11-23)

Huawei Proprietary and Confidential

33

Copyright © Huawei Technologies Co., Ltd.

 

 

 

 

Page 50
Image 50
Huawei MG323 manual IndDescr IndValue