Manuals / JVC / Computer Equipment / Projector

JVC 340 SC, 330, 370 SC service manual Power-On Codes

Models: 340 SC 370 SC 330

1 163

Download 163 pages 51.75 Kb

Page 143

5.2Power-On Codes

Chapter 5---Troubleshooting

LED

On-Screen Text

Description

xProblem with decoder module data.

yProblem with decode input.

#Loss of horizontal sweep detected.

Codes indicating a software bug—system should keep running.

GInternal error code not recognized.

HIncoming command not recognized.

JInternal password control code bad.

KDAC reference not recognized.

LTimer table reference not valid.

MIIC reference not recognized.

NRTG reference not recognized.

PInternal convergence axis reference invalid.

QInternal channel parameter reference not recognized.

RInternal convergence data index invalid.

5.2Power-On Codes

The projector performs a series of operations when power is turned on. Codes for these operations are shown on a LED display at the rear of the projector. Operations are divided into two (2) sets:

1.The first (1st) set occurs when standby power is applied. For example, the projector is plugged into a proper outlet and the circuit breaker on the side of the projector is ON.

2.The second (2nd) set takes place when the user issues a “power-on” command. For example, presses “Control-P” on a VT-100 terminal or “POWER ON” on the I/R or tethered remote.

First Set

The first (1st) set of operations occurs when the +5volts is activated to the SCB prior to applying power to the projector (standby mode). After the +5volts is applied, the LED should display a zero or #—if not displayed, there is a problem with the SCB.

Verify the following conditions:

1.Verify that +5volts and +24volts standby LEDs are lit. If STB +5volts and +24volts are not present, verify that the projector is plugged into a proper outlet and that the circuit breaker on the right side of the projector is on. If

5-3	Model 330, 340SC, and 370SC Service Manual

Image 143

JVC 340 SC, 330, 370 SC service manual Power-On Codes

Contents

Model Model 340 SC Model 370 SC DECLARATION OF CONFORMITYHughes-JVC Technology Corporation SERVICE MANUALConfidential and proprietary information Manufacturer Hughes-JVC Technology CorporationWarnings and Cautions Safety InformationSafety Equipment IntroductionProjector Weight Installation SafeguardsUltra Violet and Infrared Light Heat SafeguardsLight Safeguards FansUltraviolet radiation, dangerous glare, and high internal gas pressure Power Fluid SafeguardsPower Supply Ventilation and Foreign Object RetrievalModel 330, 340SC, and 370SC Service Manual SafetyModel 330, 340SC, and 370SC Service Manual Safety1.1 Acronyms Used In Manual 1.0 IntroductionModel 330, 340SC and 370SC Service Manual 1.2 Safety1.3 Updates 1.4 Hardware CompatibilityVideo Amplifier Board 2.0 Functional Descriptions Contents2.1 Cover and Base 2.3 Electronics Systems Overview 2.2 External Power RequirementsThe Model 330, 340SC and 370SC Electronics System consists of System Power Supply 2.4 System PowerFigure 2-2 Backplane Status Indicators ∇ Model 330. Model 340SC = +25V/80a Model 370SC = +30V/100a 2. +24V Standby and Arc Lamp power supplies turn on Arc Lamp Ignitor 22-30V depending on projector model High Voltage Power Supply Pins 1,4,5,10 not used High Voltage Power SupplyPower and Control Connector Model 330, 340SC, and 370SC Service ManualCRT anode voltages are not user controllable. They are fixed at 32KV with a maximum output of 2.1mA total or 0.7mA per CRT. The anode voltage is the primary acceleration voltage for the CRT. Other bias voltages screen grid, G2, and control grid, G1 are used to control the level of beam current. The anode voltage is routed out of the top of the HVPS, into the CRT housing to three 3 bulkhead connectors. From there, the anode wires on the CRTs route the anode voltage directly to the CRT. The anode voltages are overvoltage and overcurrent protected in the event of short circuits or CRT arcing 2.5 Card Cage 370SC 2.6 Circuit BoardsDescription 340SC2-16 Model 330, 340SC, and 370SC Service ManualChapter 2-Functional Descriptions 2-17 Figure 2-10 Raster Generation Block DiagramModel 330, 340SC and 370SC Service Manual Chapter 2-Functional DescriptionRaster Timing Generator Board RTG p/n Sync Detector and Selector Sync GeneratorVSYNC Detector, Field Separator, and Mux Phase Locked LoopSerration and Equalization Lockout Adjustment Counters Description Serial CommunicationInformation IICCLK Raster Timing Generator I/OHorizontal Deflection Board Inputs Interlocks and ProtectionHorizontal Deflection Board P/N 102523 HDB System Power SupplyVertical Oscillator Horizontal Centering Horizontal Phase Locked LoopHorizontal Power Supply Output Section Flyback SwitchingGeometric Correction Description Horizontal Sweep Failure DetectionSerial Communication InformationHorizontal Deflection Board I/O Raster Timing Generator Inputs Vertical Deflection Board P/N 102521VDBSystem Power Supply Interlocks and ProtectionVertical raster centering Top and bottom pincushion correction Vertical Preamps Side Pincushion and Keystone Correction Vertical AmplifiersSweep Failure Detection Top and Bottom Pincushion and Keystone Correction Horizontal Linearity CorrectionRXCORR RYCORR GXCORR GYCORR BXCORR Correction AmplifiersSerial Communication System Controller Board General I/OInformation DescriptionSystem Controller Board Outputs Internal Interlocks and ShutdownsInput Output2-42 Model 330, 340SC and 370SC Service ManualChapter 2-Functional Descriptions Video Processor Board P/N 104672 VPB Decoder B, G, and R Brightness and Contrast Amplifiers Video/Sync MuxV & H Sync Strip SG Sync StripGamma Correction On-Screen SwitchSwitch Logic and Video Enable RGB Sensitivity and Threshold Amplifier Information ILA BiasDynamic Focus Amplifier Serial CommunicationDescription General I/OSystem Controller Board InputRaster Timing Generator System Controller BoardOutputs DescriptionVertical Deflection Board Decoder Image Light AmplifiersOutputs DescriptionOutputs High Voltage Power SupplySystem Power Supply Interlocks and ProtectionInternal Video Amplifier Board P/N 103567 or 103774 VABOutput Failure Detection Video SignalArc Protection DC RestoreEnable Circuit Beam Current SenseGeneral I/O This section provides a comprehensive description of the inputs to and outputs from the VAB. The I/O description are arranged by the source/destination of the signal and so the assemblies communicated with are used as the primary heading of each group of signals and then are further subdivided into inputs and outputs. In each case, the signals direction is noted, with input referring to an input to the VAB, and output to an output from the VAB e.g. under Video Processor Board Input CLAMP refers to the signal CLAMP that is an input to the VAB from the Video Processor Board. When test points are provided for the I/O they are notedVideo Processor Board Description System Controller Board P/N 104668 SCBSystem Power Supply InputsGeneral Functional Description Page Expanded Memory Working and Compressed MemoryDACs Correction Address GeneratorOverlay Address Generator Overlay MemoryIR Interface Overlay InterfaceLED Display Buffers and Logic RS232 InterfaceGeneral I/O IIC InterfaceSerial Interface There are three 3 ports for receiving IR radiation. One 1 is located on the front of the projector just above the Green projection lens and the other two 2 are located on the rear panel. One of the receivers on the rear panel is located next to the LED display and, like the front receiver, is used for directly receiving IR radiation. The other rear-mounted receiver is used for connecting an IR repeater, which is an optional device that allows the user to control the projector from up to 150 feet awayDescription Video Processor BoardDescription InputDescription Raster Timing GeneratorDescription InputDescription Vertical Deflection BoardDescription InputHorizontal Deflection Board Backplane Board p/n BackplaneRelay Lens CRT AssemblyImage Light Amplifier ILA Assembly 2.7 Optical Sectionlight. The vertically polarized light then passes through the prism to the projector lens. The ILA assembly combines the input signal from the CRT with the high intensity light from the arc lamp. Thus, the brightness of the screen image does not depend on the brightness of the CRT but on the light from the xenon arc lamp. A more detailed explanation of the ILA assembly is in Section 2.8 at the end of this chapter Screen CRT ImageCombined Image and High Intensity Light=Bright ImageProjection Lens Arc Lamp AssemblyPrism Optical Subassemblies 2.8 Image Light AmplifierFigure 2-20 The Hughes-JVC Image Light Amplifier Figure 2-21 Simplified illustration of the Series 300 Projector optical path Chapter 3---Service Adjustments 3.0 Service Adjustments3.1 Service Cover-Off Power-On Sequence ContentsMain AC Circuit Breaker 3.2 CRT Yoke Rotation 7. View R 3.3 Vertical Size Tracking 3.4 Vertical Linearity Tracking 3.5 Horizontal Size Tracking Note On Super Contrast Ila Assemblies 3.6 ILA Bias Settings3.7 CRT Mechanical Focus The lower-left rod adjusts the CRT to ILA distance z- axis 2. Increase Size to 100% horizontal and vertical 3.8 Electronic Focus Front/Rear Jumpers 3.9 Jumper SettingsF R O N T p ro jectio n R E A R p ro jectio nJ601 Inverted Vertical JumpersJ300 J301 J500 J501 J200 J201 J600 J400Sensitivity/Threshold Offset 3.10 G2 AdjustmentG2 Setting To set G2 1. Cut off R and B and view G Model 330 Arc Lamp Alignment and Focus 3.11 Arc Lamp Alignment and FocusTo refocus the Model 330 Arc Lamp X-Axis Plate Z-Axis Screwplate Model 340SC and 370SC Arc Lamp Alignment and FocusY-Axis Plate Figure 3-9. Model 340SC and 370SC Arc Lamp Adjustments 3.12 Arc Lamp Current Adjustment2. Measure the number of millivolts between pins 3 and 4 on SPS J505 3-23 Chapter 3---Service AdjustmentsModel 330, 340SC, 370SC Service Manual Model 330, 340SC, and 370SC Service Manual 4.0 Maintenance Remove/Replace4.1 Introduction Contentsbefore performing any removal and replacement procedures WARNING!!! Disconnect AC power from the projectorFigure 4-1 Major components of the Model 330 Projector Chapter 4-MaintenanceModel 330, 340SC, and 370SC Service Manual Figure 4-2 Major components of the Model 340SC and 370SC Projectors Chapter 4-MaintenanceModel 330. 340SC, 370SC Service Manual 4.3 Ventilation Filters 4.2 Projector CoversModel 330 Ignitor and Arc Lamp Assembly P/N 900611S Removal 4.4 Arc Lamp AssemblyJ503 and J504 Ignitor Assembly Location on Wire ColorWire goes to IgnitorStart Capacitor Squirrel Cage Fan Cable Interlock Switch Fan Connector Circuit BreakerJ503 J504 J505 Interlock Switch Lamp Current Adjust 3-mm Set Screw Mounting Screws Collimating Condensing Lens Adjustment4.5 System Power Supply screws under lip AC Power Terminal Block Ground Main AC Circuit Breaker Mounting4.6 Electronics Module 11. Replace the module in the reverse order Model 330 CRT Removal 4.7 Cathode Ray Tube CRT5. Remove the video amplifier board from the CRT Assembly Section Model 330, 340SC, and 370SC Service Manual Figure 4-10 Model 340SC and 370SC CRT AssemblyFigure 4-11 CRT Z-Axis Focus Adjustment Rods circled Chapter 4-MaintenanceTo remove a VAB see Figure 4-9 or Figure 4.8 Video Amplifier Board VABModel 340SC and 370SC CRT Removal To remove the CRT yoke see Figure 4-9 or Figure 4.9 CRT Yoke4.10 High Voltage Power Supply HVPS 4.11 Card Cage Printed Circuit Boards 4.12 Image Light Amplifier Assembly Lens Locking Rods 4.13 Projection Lens4-24 Chapter 4-MaintenanceModel 330. 340SC, 370SC Service Manual Table 4-2 for reference to part numbers, if necessaryLens Part Number or Designation 4.14 SCB Socket Battery ReplacementCAUTION! Never place the socket battery on a metal Lens ThrowCAUTION! Never place the socket battery on 340SC 4.15 Recommended SparesDescription QuantityContents 5.0 Troubleshooting5.1 General Information Page 5.2 Power-On Codes Description Second SetCode Description 5.3 Break PointsCode MeaningDescription Resetting the ProjectorBreak Trap Data from the Diagnostics Menu CodeModel 330, 340SC, and 370SC Service Manual 5.4 Main Menu StructureVersion 5.1.0 Software Menu Diagram Chapter 5---TroubleshootingSymptom to Problem andPossible Solution ServiceSymptom to Problem andPossible Solution ServiceSymptom to Problem andPossible Solution ServiceSymptom to Problem andPossible Solution ServiceSymptom to Problem andPossible Solution ServiceSymptom to Problem andPossible Solution ServiceIntermittent Glossary of Terms Cold Mirror Test pattern of black-to-white gradation bars. The more levels Intensity Lumen Retrace Phase adjustmentResolution RasterScan See Arc Lamp temporarily with the Executive I/R remoteGlossary Model 330, 340SC, and 370SC Service Manual