Manuals / JVC / Computer Equipment / Projector

JVC 330, 370 SC, 340 SC service manual Video Amplifier Board

Models: 340 SC 370 SC 330

1 163

Download 163 pages 51.75 Kb

Page 12

Manual background

Chapter 1---Introduction

	Printed Circuit Boards			330			340SC	370SC

	Video Amplifier Board			103774		103774		103774

	System Controller Board			104668		104668		104668

Table 1-2Projector Model Comparisons
	330 Model	340SC Model					370SC Model

Different
3,000 lumens		4,200 lumens					6,800 lumens

2,500 ANSI lumens		3,700 ANSI lumens					6,000 ANSI lumens

220V AC, 20A, 60Hz		220V AC, 20A, 60Hz					220V AC, 30A, 60Hz

2,700 Watts power		3,325 Watts power					4,550 Watts power

1,500 W Xenon arc lamp		2,000 W Xenon arc lamp					3,000 W Xenon arc lamp

Same
5.2.1 software		5.2.1 software					5.2.1 software

graphics enhancement		graphics enhancement					graphics enhancement

30 memories		30 memories					30 memories

decoder board option		decoder board option					decoder board option

Model 330, 340SC and 370SC Service Manual

1-3

Image 12

JVC 330, 370 SC, 340 SC service manual Video Amplifier Board

Contents

DECLARATION OF CONFORMITY Hughes-JVC Technology CorporationSERVICE MANUAL Model Model 340 SC Model 370 SCManufacturer Hughes-JVC Technology Corporation Confidential and proprietary informationSafety Information Safety EquipmentIntroduction Warnings and CautionsInstallation Safeguards Projector WeightHeat Safeguards Light SafeguardsFans Ultra Violet and Infrared LightUltraviolet radiation, dangerous glare, and high internal gas pressure Fluid Safeguards Power SupplyVentilation and Foreign Object Retrieval PowerSafety Model 330, 340SC, and 370SC Service ManualSafety Model 330, 340SC, and 370SC Service Manual1.0 Introduction 1.1 Acronyms Used In Manual1.2 Safety 1.3 Updates1.4 Hardware Compatibility Model 330, 340SC and 370SC Service ManualVideo Amplifier Board Contents 2.0 Functional Descriptions2.1 Cover and Base 2.2 External Power Requirements 2.3 Electronics Systems OverviewThe Model 330, 340SC and 370SC Electronics System consists of 2.4 System Power System Power SupplyFigure 2-2 Backplane Status Indicators ∇ Model 330. Model 340SC = +25V/80a Model 370SC = +30V/100a 2. +24V Standby and Arc Lamp power supplies turn on Arc Lamp Ignitor 22-30V depending on projector model High Voltage Power Supply High Voltage Power Supply Power and Control ConnectorModel 330, 340SC, and 370SC Service Manual Pins 1,4,5,10 not usedCRT anode voltages are not user controllable. They are fixed at 32KV with a maximum output of 2.1mA total or 0.7mA per CRT. The anode voltage is the primary acceleration voltage for the CRT. Other bias voltages screen grid, G2, and control grid, G1 are used to control the level of beam current. The anode voltage is routed out of the top of the HVPS, into the CRT housing to three 3 bulkhead connectors. From there, the anode wires on the CRTs route the anode voltage directly to the CRT. The anode voltages are overvoltage and overcurrent protected in the event of short circuits or CRT arcing 2.5 Card Cage 2.6 Circuit Boards Description340SC 370SCModel 330, 340SC, and 370SC Service Manual Chapter 2-Functional Descriptions2-16 Figure 2-10 Raster Generation Block Diagram Model 330, 340SC and 370SC Service ManualChapter 2-Functional Description 2-17Raster Timing Generator Board RTG p/n Sync Generator Sync Detector and SelectorPhase Locked Loop Serration and Equalization LockoutVSYNC Detector, Field Separator, and Mux Adjustment Counters Serial Communication InformationDescription Raster Timing Generator I/O IICCLKHorizontal Deflection Board Interlocks and Protection Horizontal Deflection Board P/N 102523 HDBSystem Power Supply InputsVertical Oscillator Horizontal Phase Locked Loop Horizontal Power SupplyHorizontal Centering Flyback Switching Geometric CorrectionOutput Section Horizontal Sweep Failure Detection Serial CommunicationInformation DescriptionHorizontal Deflection Board I/O Raster Timing Generator Vertical Deflection Board P/N 102521VDB System Power SupplyInterlocks and Protection InputsVertical raster centering Top and bottom pincushion correction Vertical Preamps Vertical Amplifiers Sweep Failure DetectionSide Pincushion and Keystone Correction Horizontal Linearity Correction Top and Bottom Pincushion and Keystone CorrectionCorrection Amplifiers Serial CommunicationRXCORR RYCORR GXCORR GYCORR BXCORR General I/O InformationDescription System Controller BoardSystem Controller Board Outputs Interlocks and Shutdowns InputOutput InternalModel 330, 340SC and 370SC Service Manual Chapter 2-Functional Descriptions2-42 Video Processor Board P/N 104672 VPB Decoder Video/Sync Mux V & H Sync StripSG Sync Strip B, G, and R Brightness and Contrast AmplifiersOn-Screen Switch Switch Logic and Video EnableGamma Correction RGB Sensitivity and Threshold Amplifier ILA Bias Dynamic Focus AmplifierSerial Communication InformationGeneral I/O System Controller BoardInput DescriptionSystem Controller Board OutputsDescription Raster Timing GeneratorVertical Deflection Board Image Light Amplifiers OutputsDescription DecoderHigh Voltage Power Supply System Power SupplyInterlocks and Protection OutputsVideo Amplifier Board P/N 103567 or 103774 VAB OutputInternal Video Signal Failure DetectionDC Restore Enable CircuitBeam Current Sense Arc ProtectionThis section provides a comprehensive description of the inputs to and outputs from the VAB. The I/O description are arranged by the source/destination of the signal and so the assemblies communicated with are used as the primary heading of each group of signals and then are further subdivided into inputs and outputs. In each case, the signals direction is noted, with input referring to an input to the VAB, and output to an output from the VAB e.g. under Video Processor Board Input CLAMP refers to the signal CLAMP that is an input to the VAB from the Video Processor Board. When test points are provided for the I/O they are noted General I/OVideo Processor Board System Controller Board P/N 104668 SCB System Power SupplyInputs DescriptionGeneral Functional Description Page Working and Compressed Memory Expanded MemoryCorrection Address Generator DACsOverlay Memory Overlay Address GeneratorOverlay Interface LED Display Buffers and LogicRS232 Interface IR InterfaceIIC Interface Serial InterfaceThere are three 3 ports for receiving IR radiation. One 1 is located on the front of the projector just above the Green projection lens and the other two 2 are located on the rear panel. One of the receivers on the rear panel is located next to the LED display and, like the front receiver, is used for directly receiving IR radiation. The other rear-mounted receiver is used for connecting an IR repeater, which is an optional device that allows the user to control the projector from up to 150 feet away General I/OVideo Processor Board DescriptionInput DescriptionRaster Timing Generator DescriptionInput DescriptionVertical Deflection Board DescriptionInput DescriptionHorizontal Deflection Board Backplane Backplane Board p/nCRT Assembly Image Light Amplifier ILA Assembly2.7 Optical Section Relay Lenslight. The vertically polarized light then passes through the prism to the projector lens. The ILA assembly combines the input signal from the CRT with the high intensity light from the arc lamp. Thus, the brightness of the screen image does not depend on the brightness of the CRT but on the light from the xenon arc lamp. A more detailed explanation of the ILA assembly is in Section 2.8 at the end of this chapter CRT Image Combined Image and HighIntensity Light=Bright Image ScreenArc Lamp Assembly PrismProjection Lens 2.8 Image Light Amplifier Optical SubassembliesFigure 2-20 The Hughes-JVC Image Light Amplifier Figure 2-21 Simplified illustration of the Series 300 Projector optical path 3.0 Service Adjustments 3.1 Service Cover-Off Power-On SequenceContents Chapter 3---Service AdjustmentsMain AC Circuit Breaker 3.2 CRT Yoke Rotation 7. View R 3.3 Vertical Size Tracking 3.4 Vertical Linearity Tracking 3.5 Horizontal Size Tracking 3.6 ILA Bias Settings Note On Super Contrast Ila Assemblies3.7 CRT Mechanical Focus The lower-left rod adjusts the CRT to ILA distance z- axis 2. Increase Size to 100% horizontal and vertical 3.8 Electronic Focus 3.9 Jumper Settings Front/Rear JumpersR E A R p ro jectio n F R O N T p ro jectio nInverted Vertical Jumpers J300 J301 J500 J501J200 J201 J600 J400 J6013.10 G2 Adjustment G2 SettingSensitivity/Threshold Offset To set G2 1. Cut off R and B and view G 3.11 Arc Lamp Alignment and Focus Model 330 Arc Lamp Alignment and FocusTo refocus the Model 330 Arc Lamp Model 340SC and 370SC Arc Lamp Alignment and Focus Y-Axis PlateX-Axis Plate Z-Axis Screwplate 3.12 Arc Lamp Current Adjustment Figure 3-9. Model 340SC and 370SC Arc Lamp Adjustments2. Measure the number of millivolts between pins 3 and 4 on SPS J505 Chapter 3---Service Adjustments Model 330, 340SC, 370SC Service Manual3-23 4.0 Maintenance Remove/Replace 4.1 IntroductionContents Model 330, 340SC, and 370SC Service ManualWARNING!!! Disconnect AC power from the projector before performing any removal and replacement proceduresChapter 4-Maintenance Model 330, 340SC, and 370SC Service ManualFigure 4-1 Major components of the Model 330 Projector Chapter 4-Maintenance Model 330. 340SC, 370SC Service ManualFigure 4-2 Major components of the Model 340SC and 370SC Projectors 4.2 Projector Covers 4.3 Ventilation Filters4.4 Arc Lamp Assembly Model 330 Ignitor and Arc Lamp Assembly P/N 900611S RemovalJ503 and J504 Ignitor Assembly Wire Color Wire goes toIgnitor Location onInterlock Switch Fan Connector Circuit Breaker J503 J504 J505 Interlock Switch Lamp Current AdjustStart Capacitor Squirrel Cage Fan Cable Collimating Condensing Lens Adjustment 3-mm Set Screw Mounting Screws4.5 System Power Supply AC Power Terminal Block Ground Main AC Circuit Breaker Mounting screws under lip4.6 Electronics Module 11. Replace the module in the reverse order 4.7 Cathode Ray Tube CRT Model 330 CRT Removal5. Remove the video amplifier board from the CRT Assembly Section Figure 4-10 Model 340SC and 370SC CRT Assembly Figure 4-11 CRT Z-Axis Focus Adjustment Rods circledChapter 4-Maintenance Model 330, 340SC, and 370SC Service Manual4.8 Video Amplifier Board VAB Model 340SC and 370SC CRT RemovalTo remove a VAB see Figure 4-9 or Figure 4.9 CRT Yoke To remove the CRT yoke see Figure 4-9 or Figure4.10 High Voltage Power Supply HVPS 4.11 Card Cage Printed Circuit Boards 4.12 Image Light Amplifier Assembly 4.13 Projection Lens Lens Locking RodsChapter 4-Maintenance Model 330. 340SC, 370SC Service ManualTable 4-2 for reference to part numbers, if necessary 4-244.14 SCB Socket Battery Replacement CAUTION! Never place the socket battery on a metalLens Throw Lens Part Number or DesignationCAUTION! Never place the socket battery on 4.15 Recommended Spares DescriptionQuantity 340SC5.0 Troubleshooting 5.1 General InformationContents Page 5.2 Power-On Codes Second Set CodeDescription 5.3 Break Points CodeMeaning DescriptionResetting the Projector Break Trap Data from the Diagnostics MenuCode Description5.4 Main Menu Structure Version 5.1.0 Software Menu DiagramChapter 5---Troubleshooting Model 330, 340SC, and 370SC Service ManualProblem and Possible SolutionService Symptom toProblem and Possible SolutionService Symptom toProblem and Possible SolutionService Symptom toProblem and Possible SolutionService Symptom toProblem and Possible SolutionService Symptom toProblem and Possible SolutionService Symptom toIntermittent Glossary of Terms Cold Mirror Test pattern of black-to-white gradation bars. The more levels Intensity Lumen Phase adjustment ResolutionRaster RetraceScan temporarily with the Executive I/R remote See Arc LampModel 330, 340SC, and 370SC Service Manual Glossary