Procedure, Removal | Lincoln Electric SVM150-A instruction

Return to Section TOC

Return to Section TOC

Return to Master TOC

Return to Master TOC

F-51

F-51

TROUBLESHOOTING & REPAIR

POWER MODULE ASSEMBLY

REMOVAL AND REPLACEMENT

FIGURE F. 21 – POWER MODULE CONNECTIONS

TEMPERATURE

SWITCH POSITIVE (+) STRAP

W8

W9
POWER	W6
POWER
MODULE
PC BOARD

POSITIVE (+)

STRAP

Return to Section TOC

Return to Section TOC

Return to Master TOC

Return to Master TOC

PROCEDURE

Removal

Refer to Figures F.21 and F.22.

1.Turn the engine off.

2.Perform the Case Cover Removal proce- dure.

3.Perform the Power Module Capacitor Discharge procedure.

4.Label heavy leads W8 and W9 and, using the 7/16" wrench, remove the nuts, lock washers, and flat washers holding them to the Power Module PC board.

5.Using the 7/16" wrench, loosen the nuts on the positive terminals of the power capaci- tors. Then remove the nuts, lock washers, and flat washers from the terminals where the positive straps connect to the Power Module PC board. Flip the straps out of the way.

6.Using the 7/16" wrench, loosen the center nut on the negative strap. Using the 7/16" wrench, remove the two bolts, lock washers and flat washers from the diode module. Remove the strap.

RANGER 250

Image 101

Lincoln Electric SVM150-A service manual Power Module Assembly Removal and Replacement, Procedure

Contents

Ranger TM Ranger Safety Fumes and Gases can be dangerous Electric Shock can killARC Rays can burn Iii Welding Sparks can cause fire or explosionCylinder may explode if damaged Sûreté Pour Soudage a L’Arc Précautions DE Sûreté Master Table of Contents for ALL Sections Table of Contents Installation Section Technical Specifications Ranger 250 K1725-1/K1725-2 InstallationWeight Speed RPM Location and Ventilation Safety Precautions Additional Safety Precautions Electrical Output Connections Figure A.1 Ranger 250 Output Connections Welding Output Cables Auxiliary Power Receptacles Cable InstallationStandby Power Connections Cable Cable Size for Amps Length 100% Duty Cycle Figure A.2 Connection of the Ranger 250 to Premises Wiring Table of Contents Operation Section Operating Instructions Safety InstructionsOperation Controls and Settings Design Features Figure B.1 Case Front Panel Controls Engine Controls Welding Controls Engine OperationBefore Starting the Engine Check and fill the engine oil level BREAK-IN Period Starting the EngineStopping the Engine Table B.1 Typical Ranger 250 Fuel Consumption Welder OperationGeneral Information Constant Current CC-STICK Welding Stick WeldingPipe Welding Table B.2 Typical Current RANGES1 for Tungsten ELECTRODES2 Wire WELDING-CV Auxiliary PowerTIG Welding ARC Gouging Table B.4 Ranger 250 Simultaneous Welding and Power Loads Simultaneous Welding and Auxiliary Power Loads Table of Contents Accessories Field Installed Options OPTIONS/ACCESSORIESTIG Welding Accessories Semiautomatic Fcaw and MIG Welding Accessories Connection of Lincoln Electric Wire Feeders Accessories Place the Weld Terminals switch Return to Section TOC To Section TOC Accessories Terminals Remotely Controlled Connection of the LN-742 to Ranger 250 see Figure C.7 Figure C.7 Ranger 250/LN-742 Connection Diagram Ranger Table of Contents Maintenance Engine Maintenance Routine and Periodic Maintenance Frequency Maintenance Required Table D.2 Onan Engine Maintenance Schedule Air Pre-Cleaner Service AIR Cleaner ServiceEngine OIL Change Engine Oil Refill Capacities Spark Plug Service Air Filter Paper Element ServiceFuel Filter Service Engine Adjustment Overspeed is Hazardous Cleaning the Battery Battery MaintenanceCharging the Battery Optional Spark Arrestor WELDER/GENERATOR Maintenance Figure D.1 Major Component Locations Table of Contents Theory of Operation Section General Description Theory of Operation Return to Weld WINDINGS, RECTIFIER, Power Module and Feedback Figure E.4 Analog Power Board and Control Board Analog Power Board and Control Board Insulated Gate Bipolar Transistor Igbt Operation Maximum Output Pulse Width ModulationMinimum Output Chopper Technology Fundamentals Switch 85VDC Diode Ranger Table of Contents Troubleshooting & Repair Section HOW to USE Troubleshooting Guide Troubleshooting & Repair PC Board can be damaged by static electricity PC Board Troubleshooting Procedures Detailed in the beginning of this manual Troubleshooting GuideObserve Safety Guidelines Test Stator Voltage Test Engine Function Problems Engine Problems Troubleshooting & Repair Engine Problems Welding Problems Materials Needed Case Cover Removal and Replacement ProcedureTest Description Replacement Procedure Case Cover Removal and Replacement ProcedureRemoval Procedure Power Module Capacitor Discharge Procedure Test Procedure Power Module Capacitor Discharge Procedure Idler Solenoid Test Figure F.3 Idler Solenoid Leads Idler Solenoid Test Engine Throttle Adjustment Test Strobe-Tach Method Engine Throttle Adjustment Test Frequency Counter Method Figure F.5 High Idle Adjustment Vibratach Method Oscilloscope Method Rotor Resistance Test Figure F.7 Rotor Brush Leads Slip Rings Brushes Rotor Resistance Test Flashing and Rotor Voltage Test Flashing and Rotor Voltage Test Oil Pressure Switch Test Figure F.9 Field Diode Rectifier Bridge and Filter Capacitor Stator Voltage Tests To test the 240 VAC winding Stator Voltage TestsTo test the 120 VAC winding To test the field winding Field Rectifier Bridge Retaining TAB Cable Capacitor To test the feeder winding Figure F.12 14-PIN Amphenol PIN Assignments To test the stator weld windings Choke Analog Power PC Board Voltage Test Figure F.14 Analog Power PC Board Analog Power PC Board Voltage Test +5 VDC +20 VDC+15 VDC 15 VDC Output Rectifier Bridge Test Figure F.15 Plug J41 and Resistor R3 Locations Output Rectifier Bridge Test When all tests are complete Description Power Module TestOther PC board components could be faulty Figure F.17 Power Module Connections Power Module Test Check Igbt for Shorts Tor terminal on the power module chopper Check Diode Module Figure F.19 Diode Module Test Heat Sink Terminals Flywheel Alternator Test Figure F.20 Plug J51 PIN Location Flywheel Alternator Test High Idle no Load Scope SettingsNormal Open Circuit Voltage Waveform 120VAC Supply MAX Control POT High Idle no Load Normal Open Circuit Voltage Waveform Stick Machine Loaded to 250 Amps AT 25 Volts Normal Weld Voltage Waveform Stick CC Normal Open Circuit Voltage Waveform Wire CV TAP Machine Loaded to 250 Amps AT 28 Volts Normal Weld Voltage Waveform Wire CV Description Removal Power Module Assembly Removal and ReplacementProcedure Replacement Power Module AssemblyRemoval and Replacement Figure F.22 Diode MODULE/POWER Module Assembly Details Power Module PC Board Removal and Replacement Figure F.23 Diode Module Mounting Details Power Capacitor Removal and Replacement Power Capacitor Removal and Replacement Output Rectifier Bridge and Choke Removal and Replacement Output Rectifier Output Rectifier Bridge and Choke Output Choke ENGINE/STATOR/ROTOR Removal and Replacement Engine Preparation and Lead Disconnection ENGINE/STATOR/ROTOR Removal and Replacement Troubleshooting & Repair Stator Lead Disconnection Figure F.28 Stator Leads Front Panel Engine/Stator/Rotor Assembly Removal Procedure Figure F.29 ENGINE/STATOR/ROTOR Assembly Removal Figure F.30 Stator and Rotor Removal Stator/Rotor Assembly Removal Rotor/Stator/Engine Reassembly Reassembly Notes General Notes on Reassembly Lead Reconnection Checklist Volt Wire Feeder Power Auxiliary Power OutputRetest After Repair Engine Output Table of Contents Electrical Diagrams Section Electrical Diagrams Wiring Diagram Ranger 250 Kohler Ranger 250 Kohler Wiring Diagram Wiring Diagram Ranger 250 Onan Ranger 250 Onan Wiring Diagram Control INTER-CONNECTION Diagram 4ELECTRICAL DIAGRAMSG-4 Output Terminal Schematic Complete Machine Schematic Analog Control Power Supply Schematic Battery Printed Circuit Board Schematic Bypass Printed Circuit Board 19462 M Schematic Chopper Printed Circuit Board 24660S Schematic Display Printed Circuit Board Schematic Weld Control Printed Circuit Board Sheet Electrical Diagrams Electrical Diagrams Electrical Diagrams Electrical Diagrams SVM Error Reporting Form