Canopy T1/E1 Multiplexer User Guide | Motorola instruction

Canopy™ T1/E1 Multiplexer

User Guide

T1E1Mux-UG-en

Issue 3

September 2004

Image 1

Motorola manual Canopy T1/E1 Multiplexer User Guide, T1E1Mux-UG-en Issue September

Contents

Canopy T1/E1 Multiplexer User Guide T1E1Mux-UG-en Issue September Table of Contents Managing Your Canopy T1/E1 Multiplexers List of Figures List of Tables List of Procedures New in This Issue Using this User GuideUsing the Latest Information Searching This User Guide Variable width bold Font Type of InformationConstant width bold Admonition General Message Label Getting Additional Help Introduction to Canopy T1/E1 MultiplexerSending Feedback Canopy T1/E1 Multiplexer with Canopy BHs Ethernet Interface IDU Physical Description StandardsRear Panel Rear panel with standard 110-v source power supply Canopy T1/E1 Multiplexer LED indicator descriptions LED status indicator descriptionsFront Panel Status Leds Specifications FeaturesPhysical Specifications Canopy T1/E1 Multiplexer physical specifications T1 port specifications Technical SpecificationsT1 framing specifications E1 port specifications E1 framing specifications Configuration Settings from Canopy FactoryLocal terminal and control interface specifications Bit Handling Capability Product Labels Power AdaptersFunctional Description of the Canopy T1/E1 Multiplexer License Keys E1 Channel Mode T1 Channel ModeChannel Modes Encoding 1 in 15 Requirement AMI Alternate Mark Inversion AMIBinary Eight Zero Substitution Coding Timing SignalingHigh Density Bipolar Order Three Encoding Master and Secondary Clocks Frequency off-set by clock type Loopback Timing Mode Loss of Clock SignalRecovered Timing Mode Timing Modes Network Timing Scenarios Slave timing set to Recovered mode Ethernet Throughput Alarms Round‐Trip Packet DelayVlan Support Power Supply Unit Safety InformationCompliance Lightning Protection Package Contents Installation ProceduresPreparing for Installation and Setup Mounting the Canopy T1/E1 Multiplexer End of procedure Connecting the Canopy T1/E1 MultiplexerT1/E1 port connector pin-out Pin Designation Direction RJ-45 Connector Connecting Power to the Canopy T1/E1 MultiplexerProcedure 2 Connecting cables to T1/E1 unit Canopy BH Pin Procedure 4 Connecting the −48 v DC power source Procedure 3 Connecting the AC adapter +3.3 v DC power source Installing Software from the CD‐ROM Initial Configuration ProceduresProcedure 5 Installing Software from the CD-ROM Issue the Start-Run-d/setup sequence File drop-down menu in GUI Using EMS Software to Configure the Unit Configuring the Canopy T1/E1 Multiplexer using the CLI Accessing the CLI using a PC + HyperTerminalProcedure 6 Configuring serial port Parameter Value Command Line Interface window Creating a Login Account Changing the Administrator Password Configuration Procedures Using the CLIProcedure 7 Changing Administrator password using the CLI Logging into the System Select Line Type T1 or E1 Procedure 8 Selecting line type T1 or E1 using the CLIAction Steps Enter get line type Select Line Coding Procedure 9 Configuring line coding using the CLIEnter set line 1/2/3/4 code HDB3/B8ZS/AMI Enter get line code Procedure 10 Configuring the Ethernet ports using the CLI Configure PortsAction Enter set canopy port auto negotiation on/off DB 266-399 / 1.8 dB 399-533 / 2.4 dB 533-655 Procedure 11 Configuring the T1 ports using the CLI Enter set master clock reference line 1/2/3/4 Enter set clock source loopback/recoveredEnter set secondary clock reference line 1/2/3/4 Enter set line 1/2/3/4 code HDB3/AMI Procedure 12 Configuring the E1 ports using the CLI Set clock source loopback Set clock source recovered Procedure 13 Configuring timing using the CLI Configure Timing End of procedure Configuration Procedures Using the EMSProcedure 14 Logging in using the EMS Login dialogue box File→Command Line Terminal from the EMS Main menu T1/E1 Multiplexer EMS main menu End of procedure Changing the Administrator Password Select Configure Line Type Procedure 16 Selecting line type T1 or E1 using the EMSProcedure 17 Configuring T1 line coding using the EMS Select Configure T1 Select Configure E1 Procedure 18 Configuring E1 line coding using the EMSProcedure 19 Configuring the Ethernet ports using the EMS Click ↓ for Master Clock Reference Line Procedure 21 Configuring the E1 ports using the EMSClick ↓ for Secondary Clock Reference Line Procedure 22 Configuring timing using the EMS Remote management overview Remote Management Through Control Port Enter get alarms Procedure 23 Displaying the alarms using the CLI Select the Alarms→T1/E1 Alarms menu Procedure 24 Displaying alarms using the EMS Procedure 25 Resetting the system using the CLI System ResetProcedure 26 Resetting the system using the EMS T1/E1 Loopback Canopy T1/E1 Multiplexer in T1/E1 Loopback mode Invoking a T1/E1 Loopback Using the EMS Invoking a T1/E1 Loopback using the CLIProcedure 27 Invoking a T1/E1 loopback using the CLI Procedure 28 Invoking a T1/E1 loopback using the EMS Firmware Upgrades Measurements from DiagnosticsComparison of diagnostic measurements Procedure 29 Upgrading firmware Click Download Fpga revision details screen End of procedure T1/E1 Port Upgrade window License KEY Upgrades Invalid key entry window Software License Terms and Conditions Terms of Warranty Canopy T1/E1 Multiplexer Obtaining Technical Support Hardware Warranty in U.S Invoking Your Warranty Rights Desired Action Syntax, Response, and Description CLI Commands to GET Status InformationEnter get canopy port auto negotiation Enter get lan port auto negotiation Enter get code line 1/2/3/4 Enter get line 1/2/3/4 length Enter get master clock reference line Enter get clock sourceEnter get secondary clock reference line Enter get firmware revision Enter get loopback line 1/2/3/4 Regulatory Compliance Information Department of Communications Canada TRADEMARKS, Product NAMES, and Service NamesEuropean Telecommunications Standards Institute Canadian Compliance Statement References