Login dialogue box | Motorola T1/E1 instruction

Canopy T1/E1 Multiplexer

September 2004

T1/E1 Multiplexer FPGA Version 3.4

Figure 17: Login dialogue box

Once you are successfully logged in, the T1/E1 Multiplexer EMS Main Menu opens (shown in Figure 18).

Issue 3

Page 46 of 73

Image 46

Motorola T1/E1 manual Login dialogue box

Contents

T1E1Mux-UG-en Issue September Canopy T1/E1 Multiplexer User Guide Table of Contents Managing Your Canopy T1/E1 Multiplexers List of Figures List of Tables List of Procedures Using the Latest Information Using this User GuideNew in This Issue Searching This User Guide Constant width bold Font Type of InformationVariable width bold Admonition General Message Label Getting Additional Help Introduction to Canopy T1/E1 MultiplexerSending Feedback Ethernet Interface Canopy T1/E1 Multiplexer with Canopy BHs IDU Physical Description StandardsRear Panel Rear panel with standard 110-v source power supply Canopy T1/E1 Multiplexer Front Panel LED status indicator descriptionsLED indicator descriptions Status Leds Physical Specifications FeaturesSpecifications Canopy T1/E1 Multiplexer physical specifications T1 framing specifications Technical SpecificationsT1 port specifications E1 port specifications Local terminal and control interface specifications Configuration Settings from Canopy FactoryE1 framing specifications Bit Handling Capability Functional Description of the Canopy T1/E1 Multiplexer Power AdaptersProduct Labels License Keys Channel Modes T1 Channel ModeE1 Channel Mode Encoding 1 in 15 Requirement AMI Alternate Mark Inversion AMIBinary Eight Zero Substitution Coding Timing SignalingHigh Density Bipolar Order Three Encoding Frequency off-set by clock type Master and Secondary Clocks Recovered Timing Mode Loss of Clock SignalLoopback Timing Mode Timing Modes Slave timing set to Recovered mode Network Timing Scenarios Ethernet Throughput Alarms Round‐Trip Packet DelayVlan Support Compliance Safety InformationPower Supply Unit Lightning Protection Preparing for Installation and Setup Installation ProceduresPackage Contents Mounting the Canopy T1/E1 Multiplexer T1/E1 port connector pin-out Connecting the Canopy T1/E1 MultiplexerEnd of procedure Pin Designation Direction Procedure 2 Connecting cables to T1/E1 unit Connecting Power to the Canopy T1/E1 MultiplexerRJ-45 Connector Canopy BH Pin Procedure 3 Connecting the AC adapter +3.3 v DC power source Procedure 4 Connecting the −48 v DC power source Procedure 5 Installing Software from the CD-ROM Initial Configuration ProceduresInstalling Software from the CD‐ROM Issue the Start-Run-d/setup sequence Using EMS Software to Configure the Unit File drop-down menu in GUI Procedure 6 Configuring serial port Accessing the CLI using a PC + HyperTerminalConfiguring the Canopy T1/E1 Multiplexer using the CLI Parameter Value Creating a Login Account Command Line Interface window Procedure 7 Changing Administrator password using the CLI Configuration Procedures Using the CLIChanging the Administrator Password Logging into the System Action Steps Procedure 8 Selecting line type T1 or E1 using the CLISelect Line Type T1 or E1 Enter get line type Enter set line 1/2/3/4 code HDB3/B8ZS/AMI Procedure 9 Configuring line coding using the CLISelect Line Coding Enter get line code Action Configure PortsProcedure 10 Configuring the Ethernet ports using the CLI Enter set canopy port auto negotiation on/off Procedure 11 Configuring the T1 ports using the CLI DB 266-399 / 1.8 dB 399-533 / 2.4 dB 533-655 Enter set master clock reference line 1/2/3/4 Enter set clock source loopback/recoveredEnter set secondary clock reference line 1/2/3/4 Procedure 12 Configuring the E1 ports using the CLI Enter set line 1/2/3/4 code HDB3/AMI Set clock source recovered Set clock source loopback Configure Timing Procedure 13 Configuring timing using the CLI End of procedure Configuration Procedures Using the EMSProcedure 14 Logging in using the EMS Login dialogue box T1/E1 Multiplexer EMS main menu End of procedure File→Command Line Terminal from the EMS Main menu Changing the Administrator Password Procedure 17 Configuring T1 line coding using the EMS Procedure 16 Selecting line type T1 or E1 using the EMSSelect Configure Line Type Select Configure T1 Select Configure E1 Procedure 18 Configuring E1 line coding using the EMSProcedure 19 Configuring the Ethernet ports using the EMS Click ↓ for Master Clock Reference Line Procedure 21 Configuring the E1 ports using the EMSClick ↓ for Secondary Clock Reference Line Procedure 22 Configuring timing using the EMS Remote Management Through Control Port Remote management overview Procedure 23 Displaying the alarms using the CLI Enter get alarms Procedure 24 Displaying alarms using the EMS Select the Alarms→T1/E1 Alarms menu Procedure 25 Resetting the system using the CLI System ResetProcedure 26 Resetting the system using the EMS Canopy T1/E1 Multiplexer in T1/E1 Loopback mode T1/E1 Loopback Procedure 27 Invoking a T1/E1 loopback using the CLI Invoking a T1/E1 Loopback using the CLIInvoking a T1/E1 Loopback Using the EMS Procedure 28 Invoking a T1/E1 loopback using the EMS Comparison of diagnostic measurements Measurements from DiagnosticsFirmware Upgrades Procedure 29 Upgrading firmware Fpga revision details screen End of procedure Click Download License KEY Upgrades T1/E1 Port Upgrade window Invalid key entry window Terms of Warranty Software License Terms and Conditions Canopy T1/E1 Multiplexer Hardware Warranty in U.S Obtaining Technical Support Invoking Your Warranty Rights Enter get canopy port auto negotiation CLI Commands to GET Status InformationDesired Action Syntax, Response, and Description Enter get lan port auto negotiation Enter get line 1/2/3/4 length Enter get code line 1/2/3/4 Enter get master clock reference line Enter get clock sourceEnter get secondary clock reference line Enter get loopback line 1/2/3/4 Enter get firmware revision Regulatory Compliance Information European Telecommunications Standards Institute TRADEMARKS, Product NAMES, and Service NamesDepartment of Communications Canada Canadian Compliance Statement References