Creating a Login Account | Motorola T1/E1 manual

Canopy T1/E1 Multiplexer	September 2004
	T1/E1 Multiplexer FPGA Version 3.4

Figure 16: Command Line Interface window

2.3.5Creating a Login Account

The system is shipped with default setting for the Administrator account. The account is active, but it is recommended you change the password for this account.

Issue 3

Page 35 of 73

Page 35

Image 35

Motorola T1/E1 manual Creating a Login Account, Command Line Interface window

Contents

Canopy T1/E1 Multiplexer User Guide T1E1Mux-UG-en Issue September Table of Contents Managing Your Canopy T1/E1 Multiplexers List of Figures List of Tables List of Procedures Searching This User Guide Using this User GuideNew in This Issue Using the Latest Information Admonition General Message Label Font Type of InformationVariable width bold Constant width bold Sending Feedback Introduction to Canopy T1/E1 MultiplexerGetting Additional Help Canopy T1/E1 Multiplexer with Canopy BHs Ethernet Interface Rear Panel StandardsIDU Physical Description Rear panel with standard 110-v source power supply Canopy T1/E1 Multiplexer Status Leds LED status indicator descriptionsLED indicator descriptions Front Panel Canopy T1/E1 Multiplexer physical specifications FeaturesSpecifications Physical Specifications E1 port specifications Technical SpecificationsT1 port specifications T1 framing specifications Bit Handling Capability Configuration Settings from Canopy FactoryE1 framing specifications Local terminal and control interface specifications License Keys Power AdaptersProduct Labels Functional Description of the Canopy T1/E1 Multiplexer Encoding T1 Channel ModeE1 Channel Mode Channel Modes Binary Eight Zero Substitution Coding Alternate Mark Inversion AMI1 in 15 Requirement AMI High Density Bipolar Order Three Encoding SignalingTiming Master and Secondary Clocks Frequency off-set by clock type Timing Modes Loss of Clock SignalLoopback Timing Mode Recovered Timing Mode Network Timing Scenarios Slave timing set to Recovered mode Ethernet Throughput Vlan Support Round‐Trip Packet DelayAlarms Lightning Protection Safety InformationPower Supply Unit Compliance Mounting the Canopy T1/E1 Multiplexer Installation ProceduresPackage Contents Preparing for Installation and Setup Pin Designation Direction Connecting the Canopy T1/E1 MultiplexerEnd of procedure T1/E1 port connector pin-out Canopy BH Pin Connecting Power to the Canopy T1/E1 MultiplexerRJ-45 Connector Procedure 2 Connecting cables to T1/E1 unit Procedure 4 Connecting the −48 v DC power source Procedure 3 Connecting the AC adapter +3.3 v DC power source Issue the Start-Run-d/setup sequence Initial Configuration ProceduresInstalling Software from the CD‐ROM Procedure 5 Installing Software from the CD-ROM File drop-down menu in GUI Using EMS Software to Configure the Unit Parameter Value Accessing the CLI using a PC + HyperTerminalConfiguring the Canopy T1/E1 Multiplexer using the CLI Procedure 6 Configuring serial port Command Line Interface window Creating a Login Account Logging into the System Configuration Procedures Using the CLIChanging the Administrator Password Procedure 7 Changing Administrator password using the CLI Enter get line type Procedure 8 Selecting line type T1 or E1 using the CLISelect Line Type T1 or E1 Action Steps Enter get line code Procedure 9 Configuring line coding using the CLISelect Line Coding Enter set line 1/2/3/4 code HDB3/B8ZS/AMI Enter set canopy port auto negotiation on/off Configure PortsProcedure 10 Configuring the Ethernet ports using the CLI Action DB 266-399 / 1.8 dB 399-533 / 2.4 dB 533-655 Procedure 11 Configuring the T1 ports using the CLI Enter set secondary clock reference line 1/2/3/4 Enter set clock source loopback/recoveredEnter set master clock reference line 1/2/3/4 Enter set line 1/2/3/4 code HDB3/AMI Procedure 12 Configuring the E1 ports using the CLI Set clock source loopback Set clock source recovered Procedure 13 Configuring timing using the CLI Configure Timing Procedure 14 Logging in using the EMS Configuration Procedures Using the EMSEnd of procedure Login dialogue box File→Command Line Terminal from the EMS Main menu T1/E1 Multiplexer EMS main menu End of procedure Changing the Administrator Password Select Configure T1 Procedure 16 Selecting line type T1 or E1 using the EMSSelect Configure Line Type Procedure 17 Configuring T1 line coding using the EMS Procedure 19 Configuring the Ethernet ports using the EMS Procedure 18 Configuring E1 line coding using the EMSSelect Configure E1 Click ↓ for Secondary Clock Reference Line Procedure 21 Configuring the E1 ports using the EMSClick ↓ for Master Clock Reference Line Procedure 22 Configuring timing using the EMS Remote management overview Remote Management Through Control Port Enter get alarms Procedure 23 Displaying the alarms using the CLI Select the Alarms→T1/E1 Alarms menu Procedure 24 Displaying alarms using the EMS Procedure 26 Resetting the system using the EMS System ResetProcedure 25 Resetting the system using the CLI T1/E1 Loopback Canopy T1/E1 Multiplexer in T1/E1 Loopback mode Procedure 28 Invoking a T1/E1 loopback using the EMS Invoking a T1/E1 Loopback using the CLIInvoking a T1/E1 Loopback Using the EMS Procedure 27 Invoking a T1/E1 loopback using the CLI Procedure 29 Upgrading firmware Measurements from DiagnosticsFirmware Upgrades Comparison of diagnostic measurements Click Download Fpga revision details screen End of procedure T1/E1 Port Upgrade window License KEY Upgrades Invalid key entry window Software License Terms and Conditions Terms of Warranty Canopy T1/E1 Multiplexer Obtaining Technical Support Hardware Warranty in U.S Invoking Your Warranty Rights Enter get lan port auto negotiation CLI Commands to GET Status InformationDesired Action Syntax, Response, and Description Enter get canopy port auto negotiation Enter get code line 1/2/3/4 Enter get line 1/2/3/4 length Enter get secondary clock reference line Enter get clock sourceEnter get master clock reference line Enter get firmware revision Enter get loopback line 1/2/3/4 Regulatory Compliance Information Canadian Compliance Statement TRADEMARKS, Product NAMES, and Service NamesDepartment of Communications Canada European Telecommunications Standards Institute References