Enter get line 1/2/3/4 length | Motorola T1/E1 specs

Canopy T1/E1 Multiplexer		September 2004
		T1/E1 Multiplexer FPGA Version 3.4

Desired Action	Syntax, Response, and Description

Get T1 line length	Enter get line [1/2/3/4] length
	where
	[1/2/3/4] represents T1 ports 1 through 4.
	The system responds	[0-133 / 0.6 dB; 133-266 /
	Line [1/2/3/4] length	[0-133 / 0.6 dB; 133-266 /
	1.2 dB; 266-399 / 1.8 dB; 399-533 / 2.4 dB; 533-655
	/ 3.0 dB]
	Gets the T1 line length. The units are in feet in decibels. If the incorrect
	line length is selected, the result could be decreased T1 quality or echo
	on voice lines.

Get T1 line code	Enter get code line [1/2/3/4]
	where
	[1/2/3/4] represents T1 ports 1 through 4
	The system responds
	Line [1/2/3/4] code [B8ZS/AMI]
	Gets the T1 line code. If the line code does not match, Bipolar
	Violations (BPVs) will occur.

Get E1 line code	Enter get code line [1/2/3/4]
	where
	[1/2/3/4] represents E1 ports 1 through 4
	The system responds:
	Line [1/2/3/4] code [HDB3/AMI]
	Gets the E1 line code. If the line code does not match, Bipolar
	Violations (BPVs) will occur.

Issue 3

Page 68 of 73

Image 68

Motorola T1/E1 manual Enter get line 1/2/3/4 length, Enter get code line 1/2/3/4

Contents

T1E1Mux-UG-en Issue September Canopy T1/E1 Multiplexer User Guide Table of Contents Managing Your Canopy T1/E1 Multiplexers List of Figures List of Tables List of Procedures Using this User Guide New in This IssueUsing the Latest Information Searching This User Guide Font Type of Information Variable width boldConstant width bold Admonition General Message Label Sending Feedback Introduction to Canopy T1/E1 MultiplexerGetting Additional Help Ethernet Interface Canopy T1/E1 Multiplexer with Canopy BHs Rear Panel StandardsIDU Physical Description Rear panel with standard 110-v source power supply Canopy T1/E1 Multiplexer LED status indicator descriptions LED indicator descriptionsFront Panel Status Leds Features SpecificationsPhysical Specifications Canopy T1/E1 Multiplexer physical specifications Technical Specifications T1 port specificationsT1 framing specifications E1 port specifications Configuration Settings from Canopy Factory E1 framing specificationsLocal terminal and control interface specifications Bit Handling Capability Power Adapters Product LabelsFunctional Description of the Canopy T1/E1 Multiplexer License Keys T1 Channel Mode E1 Channel ModeChannel Modes Encoding Binary Eight Zero Substitution Coding Alternate Mark Inversion AMI1 in 15 Requirement AMI High Density Bipolar Order Three Encoding SignalingTiming Frequency off-set by clock type Master and Secondary Clocks Loss of Clock Signal Loopback Timing ModeRecovered Timing Mode Timing Modes Slave timing set to Recovered mode Network Timing Scenarios Ethernet Throughput Vlan Support Round‐Trip Packet DelayAlarms Safety Information Power Supply UnitCompliance Lightning Protection Installation Procedures Package ContentsPreparing for Installation and Setup Mounting the Canopy T1/E1 Multiplexer Connecting the Canopy T1/E1 Multiplexer End of procedureT1/E1 port connector pin-out Pin Designation Direction Connecting Power to the Canopy T1/E1 Multiplexer RJ-45 ConnectorProcedure 2 Connecting cables to T1/E1 unit Canopy BH Pin Procedure 3 Connecting the AC adapter +3.3 v DC power source Procedure 4 Connecting the −48 v DC power source Initial Configuration Procedures Installing Software from the CD‐ROMProcedure 5 Installing Software from the CD-ROM Issue the Start-Run-d/setup sequence Using EMS Software to Configure the Unit File drop-down menu in GUI Accessing the CLI using a PC + HyperTerminal Configuring the Canopy T1/E1 Multiplexer using the CLIProcedure 6 Configuring serial port Parameter Value Creating a Login Account Command Line Interface window Configuration Procedures Using the CLI Changing the Administrator PasswordProcedure 7 Changing Administrator password using the CLI Logging into the System Procedure 8 Selecting line type T1 or E1 using the CLI Select Line Type T1 or E1Action Steps Enter get line type Procedure 9 Configuring line coding using the CLI Select Line CodingEnter set line 1/2/3/4 code HDB3/B8ZS/AMI Enter get line code Configure Ports Procedure 10 Configuring the Ethernet ports using the CLIAction Enter set canopy port auto negotiation on/off Procedure 11 Configuring the T1 ports using the CLI DB 266-399 / 1.8 dB 399-533 / 2.4 dB 533-655 Enter set secondary clock reference line 1/2/3/4 Enter set clock source loopback/recoveredEnter set master clock reference line 1/2/3/4 Procedure 12 Configuring the E1 ports using the CLI Enter set line 1/2/3/4 code HDB3/AMI Set clock source recovered Set clock source loopback Configure Timing Procedure 13 Configuring timing using the CLI Procedure 14 Logging in using the EMS Configuration Procedures Using the EMSEnd of procedure Login dialogue box T1/E1 Multiplexer EMS main menu End of procedure File→Command Line Terminal from the EMS Main menu Changing the Administrator Password Procedure 16 Selecting line type T1 or E1 using the EMS Select Configure Line TypeProcedure 17 Configuring T1 line coding using the EMS Select Configure T1 Procedure 19 Configuring the Ethernet ports using the EMS Procedure 18 Configuring E1 line coding using the EMSSelect Configure E1 Click ↓ for Secondary Clock Reference Line Procedure 21 Configuring the E1 ports using the EMSClick ↓ for Master Clock Reference Line Procedure 22 Configuring timing using the EMS Remote Management Through Control Port Remote management overview Procedure 23 Displaying the alarms using the CLI Enter get alarms Procedure 24 Displaying alarms using the EMS Select the Alarms→T1/E1 Alarms menu Procedure 26 Resetting the system using the EMS System ResetProcedure 25 Resetting the system using the CLI Canopy T1/E1 Multiplexer in T1/E1 Loopback mode T1/E1 Loopback Invoking a T1/E1 Loopback using the CLI Invoking a T1/E1 Loopback Using the EMSProcedure 27 Invoking a T1/E1 loopback using the CLI Procedure 28 Invoking a T1/E1 loopback using the EMS Measurements from Diagnostics Firmware UpgradesComparison of diagnostic measurements Procedure 29 Upgrading firmware Fpga revision details screen End of procedure Click Download License KEY Upgrades T1/E1 Port Upgrade window Invalid key entry window Terms of Warranty Software License Terms and Conditions Canopy T1/E1 Multiplexer Hardware Warranty in U.S Obtaining Technical Support Invoking Your Warranty Rights CLI Commands to GET Status Information Desired Action Syntax, Response, and DescriptionEnter get canopy port auto negotiation Enter get lan port auto negotiation Enter get line 1/2/3/4 length Enter get code line 1/2/3/4 Enter get secondary clock reference line Enter get clock sourceEnter get master clock reference line Enter get loopback line 1/2/3/4 Enter get firmware revision Regulatory Compliance Information TRADEMARKS, Product NAMES, and Service Names Department of Communications CanadaEuropean Telecommunications Standards Institute Canadian Compliance Statement References