Front Panel, Status Leds | Motorola T1/E1 guide

Canopy T1/E1 Multiplexer	September 2004
	T1/E1 Multiplexer FPGA Version 3.4

1.2.5Front Panel

The control port and indicator LEDs are located on the front panel of the unit.

Figure 6: Canopy T1/E1 Multiplexer front panel

Status LEDS

The status indicator LEDS on the front of the Canopy T1/E1 Multiplexer are listed in Table 3.

	Table 3: LED status indicator descriptions

LED	LED indicator descriptions

PWR	ON when main power supply is OK; OFF when a malfunction is
	detected
RDY	ON when self-test is successfully completed; OFF during self-test; and
	BLINKING when self-test fails

CANOPY LINK	OFF when line is not active; ON when Canopy BH Ethernet line is OK

CANOPY ACT	OFF when no activity; BLINKNG when frames are being transmitted or
	received on the line

LAN LINK	OFF when line is not active; ON when line is OK

Issue 3

Page 14 of 73

Image 14

Motorola T1/E1 manual Front Panel, Status Leds, LED status indicator descriptions, LED indicator descriptions

Contents

T1E1Mux-UG-en Issue September Canopy T1/E1 Multiplexer User Guide Table of Contents Managing Your Canopy T1/E1 Multiplexers List of Figures List of Tables List of Procedures Using the Latest Information Using this User GuideNew in This Issue Searching This User Guide Constant width bold Font Type of InformationVariable width bold Admonition General Message Label Sending Feedback Introduction to Canopy T1/E1 MultiplexerGetting Additional Help Ethernet Interface Canopy T1/E1 Multiplexer with Canopy BHs Rear Panel StandardsIDU Physical Description Rear panel with standard 110-v source power supply Canopy T1/E1 Multiplexer Front Panel LED status indicator descriptionsLED indicator descriptions Status Leds Physical Specifications FeaturesSpecifications Canopy T1/E1 Multiplexer physical specifications T1 framing specifications Technical SpecificationsT1 port specifications E1 port specifications Local terminal and control interface specifications Configuration Settings from Canopy FactoryE1 framing specifications Bit Handling Capability Functional Description of the Canopy T1/E1 Multiplexer Power AdaptersProduct Labels License Keys Channel Modes T1 Channel ModeE1 Channel Mode Encoding Binary Eight Zero Substitution Coding Alternate Mark Inversion AMI1 in 15 Requirement AMI High Density Bipolar Order Three Encoding SignalingTiming Frequency off-set by clock type Master and Secondary Clocks Recovered Timing Mode Loss of Clock SignalLoopback Timing Mode Timing Modes Slave timing set to Recovered mode Network Timing Scenarios Ethernet Throughput Vlan Support Round‐Trip Packet DelayAlarms Compliance Safety InformationPower Supply Unit Lightning Protection Preparing for Installation and Setup Installation ProceduresPackage Contents Mounting the Canopy T1/E1 Multiplexer T1/E1 port connector pin-out Connecting the Canopy T1/E1 MultiplexerEnd of procedure Pin Designation Direction Procedure 2 Connecting cables to T1/E1 unit Connecting Power to the Canopy T1/E1 MultiplexerRJ-45 Connector Canopy BH Pin Procedure 3 Connecting the AC adapter +3.3 v DC power source Procedure 4 Connecting the −48 v DC power source Procedure 5 Installing Software from the CD-ROM Initial Configuration ProceduresInstalling Software from the CD‐ROM Issue the Start-Run-d/setup sequence Using EMS Software to Configure the Unit File drop-down menu in GUI Procedure 6 Configuring serial port Accessing the CLI using a PC + HyperTerminalConfiguring the Canopy T1/E1 Multiplexer using the CLI Parameter Value Creating a Login Account Command Line Interface window Procedure 7 Changing Administrator password using the CLI Configuration Procedures Using the CLIChanging the Administrator Password Logging into the System Action Steps Procedure 8 Selecting line type T1 or E1 using the CLISelect Line Type T1 or E1 Enter get line type Enter set line 1/2/3/4 code HDB3/B8ZS/AMI Procedure 9 Configuring line coding using the CLISelect Line Coding Enter get line code Action Configure PortsProcedure 10 Configuring the Ethernet ports using the CLI Enter set canopy port auto negotiation on/off Procedure 11 Configuring the T1 ports using the CLI DB 266-399 / 1.8 dB 399-533 / 2.4 dB 533-655 Enter set secondary clock reference line 1/2/3/4 Enter set clock source loopback/recoveredEnter set master clock reference line 1/2/3/4 Procedure 12 Configuring the E1 ports using the CLI Enter set line 1/2/3/4 code HDB3/AMI Set clock source recovered Set clock source loopback Configure Timing Procedure 13 Configuring timing using the CLI Procedure 14 Logging in using the EMS Configuration Procedures Using the EMSEnd of procedure Login dialogue box T1/E1 Multiplexer EMS main menu End of procedure File→Command Line Terminal from the EMS Main menu Changing the Administrator Password Procedure 17 Configuring T1 line coding using the EMS Procedure 16 Selecting line type T1 or E1 using the EMSSelect Configure Line Type Select Configure T1 Procedure 19 Configuring the Ethernet ports using the EMS Procedure 18 Configuring E1 line coding using the EMSSelect Configure E1 Click ↓ for Secondary Clock Reference Line Procedure 21 Configuring the E1 ports using the EMSClick ↓ for Master Clock Reference Line Procedure 22 Configuring timing using the EMS Remote Management Through Control Port Remote management overview Procedure 23 Displaying the alarms using the CLI Enter get alarms Procedure 24 Displaying alarms using the EMS Select the Alarms→T1/E1 Alarms menu Procedure 26 Resetting the system using the EMS System ResetProcedure 25 Resetting the system using the CLI Canopy T1/E1 Multiplexer in T1/E1 Loopback mode T1/E1 Loopback Procedure 27 Invoking a T1/E1 loopback using the CLI Invoking a T1/E1 Loopback using the CLIInvoking a T1/E1 Loopback Using the EMS Procedure 28 Invoking a T1/E1 loopback using the EMS Comparison of diagnostic measurements Measurements from DiagnosticsFirmware Upgrades Procedure 29 Upgrading firmware Fpga revision details screen End of procedure Click Download License KEY Upgrades T1/E1 Port Upgrade window Invalid key entry window Terms of Warranty Software License Terms and Conditions Canopy T1/E1 Multiplexer Hardware Warranty in U.S Obtaining Technical Support Invoking Your Warranty Rights Enter get canopy port auto negotiation CLI Commands to GET Status InformationDesired Action Syntax, Response, and Description Enter get lan port auto negotiation Enter get line 1/2/3/4 length Enter get code line 1/2/3/4 Enter get secondary clock reference line Enter get clock sourceEnter get master clock reference line Enter get loopback line 1/2/3/4 Enter get firmware revision Regulatory Compliance Information European Telecommunications Standards Institute TRADEMARKS, Product NAMES, and Service NamesDepartment of Communications Canada Canadian Compliance Statement References