List of Procedures | Motorola T1/E1 instruction

LIST OF PROCEDURES
Procedure 1: Affixing the Multiplexer to a rack mount	28
Procedure 2: Connecting cables to T1/E1 unit	30
Procedure 3: Connecting the AC adapter (+3.3 v DC power source)	31
Procedure 4: Connecting the −48 v DC power source	31
Procedure 5: Installing Software from the CD-ROM	32
Procedure 6: Configuring serial port	34
Procedure 7: Changing Administrator password using the CLI	36
Procedure 8: Selecting line type T1 or E1 using the CLI	37
Procedure 9: Configuring line coding using the CLI	38
Procedure 10: Configuring the Ethernet ports using the CLI	39
Procedure 11: Configuring the T1 ports using the CLI	40
Procedure 12: Configuring the E1 ports using the CLI	42
Procedure 13: Configuring timing using the CLI	44
Procedure 14: Logging in using the EMS	45
Procedure 15: Changing Administrator password using the EMS	48
Procedure 16: Selecting line type T1 or E1 using the EMS	49
Procedure 17: Configuring T1 line coding using the EMS	49
Procedure 18: Configuring E1 line coding using the EMS	50
Procedure 19: Configuring the Ethernet ports using the EMS	50
Procedure 20: Configuring the T1 ports using the EMS	50
Procedure 21: Configuring the E1 ports using the EMS	51
Procedure 22: Configuring timing using the EMS	52
Procedure 23: Displaying the alarms using the CLI	54
Procedure 24: Displaying alarms using the EMS	55
Procedure 25: Resetting the system using the CLI	56
Procedure 26: Resetting the system using the EMS	56
Procedure 27: Invoking a T1/E1 loopback using the CLI	58
Procedure 28: Invoking a T1/E1 loopback using the EMS	58
Procedure 29: Upgrading firmware	59
Procedure 30: Installing a license key to enable an additional port	61

Image 6

Motorola T1/E1 manual List of Procedures

Contents

T1E1Mux-UG-en Issue September Canopy T1/E1 Multiplexer User Guide Table of Contents Managing Your Canopy T1/E1 Multiplexers List of Figures List of Tables List of Procedures Using the Latest Information Using this User GuideNew in This Issue Searching This User Guide Constant width bold Font Type of InformationVariable width bold Admonition General Message Label Introduction to Canopy T1/E1 Multiplexer Getting Additional HelpSending Feedback Ethernet Interface Canopy T1/E1 Multiplexer with Canopy BHs Standards IDU Physical DescriptionRear Panel Rear panel with standard 110-v source power supply Canopy T1/E1 Multiplexer Front Panel LED status indicator descriptionsLED indicator descriptions Status Leds Physical Specifications FeaturesSpecifications Canopy T1/E1 Multiplexer physical specifications T1 framing specifications Technical SpecificationsT1 port specifications E1 port specifications Local terminal and control interface specifications Configuration Settings from Canopy FactoryE1 framing specifications Bit Handling Capability Functional Description of the Canopy T1/E1 Multiplexer Power AdaptersProduct Labels License Keys Channel Modes T1 Channel ModeE1 Channel Mode Encoding Alternate Mark Inversion AMI 1 in 15 Requirement AMIBinary Eight Zero Substitution Coding Signaling TimingHigh Density Bipolar Order Three Encoding Frequency off-set by clock type Master and Secondary Clocks Recovered Timing Mode Loss of Clock SignalLoopback Timing Mode Timing Modes Slave timing set to Recovered mode Network Timing Scenarios Ethernet Throughput Round‐Trip Packet Delay AlarmsVlan Support Compliance Safety InformationPower Supply Unit Lightning Protection Preparing for Installation and Setup Installation ProceduresPackage Contents Mounting the Canopy T1/E1 Multiplexer T1/E1 port connector pin-out Connecting the Canopy T1/E1 MultiplexerEnd of procedure Pin Designation Direction Procedure 2 Connecting cables to T1/E1 unit Connecting Power to the Canopy T1/E1 MultiplexerRJ-45 Connector Canopy BH Pin Procedure 3 Connecting the AC adapter +3.3 v DC power source Procedure 4 Connecting the −48 v DC power source Procedure 5 Installing Software from the CD-ROM Initial Configuration ProceduresInstalling Software from the CD‐ROM Issue the Start-Run-d/setup sequence Using EMS Software to Configure the Unit File drop-down menu in GUI Procedure 6 Configuring serial port Accessing the CLI using a PC + HyperTerminalConfiguring the Canopy T1/E1 Multiplexer using the CLI Parameter Value Creating a Login Account Command Line Interface window Procedure 7 Changing Administrator password using the CLI Configuration Procedures Using the CLIChanging the Administrator Password Logging into the System Action Steps Procedure 8 Selecting line type T1 or E1 using the CLISelect Line Type T1 or E1 Enter get line type Enter set line 1/2/3/4 code HDB3/B8ZS/AMI Procedure 9 Configuring line coding using the CLISelect Line Coding Enter get line code Action Configure PortsProcedure 10 Configuring the Ethernet ports using the CLI Enter set canopy port auto negotiation on/off Procedure 11 Configuring the T1 ports using the CLI DB 266-399 / 1.8 dB 399-533 / 2.4 dB 533-655 Enter set clock source loopback/recovered Enter set master clock reference line 1/2/3/4Enter set secondary clock reference line 1/2/3/4 Procedure 12 Configuring the E1 ports using the CLI Enter set line 1/2/3/4 code HDB3/AMI Set clock source recovered Set clock source loopback Configure Timing Procedure 13 Configuring timing using the CLI Configuration Procedures Using the EMS End of procedureProcedure 14 Logging in using the EMS Login dialogue box T1/E1 Multiplexer EMS main menu End of procedure File→Command Line Terminal from the EMS Main menu Changing the Administrator Password Procedure 17 Configuring T1 line coding using the EMS Procedure 16 Selecting line type T1 or E1 using the EMSSelect Configure Line Type Select Configure T1 Procedure 18 Configuring E1 line coding using the EMS Select Configure E1Procedure 19 Configuring the Ethernet ports using the EMS Procedure 21 Configuring the E1 ports using the EMS Click ↓ for Master Clock Reference LineClick ↓ for Secondary Clock Reference Line Procedure 22 Configuring timing using the EMS Remote Management Through Control Port Remote management overview Procedure 23 Displaying the alarms using the CLI Enter get alarms Procedure 24 Displaying alarms using the EMS Select the Alarms→T1/E1 Alarms menu System Reset Procedure 25 Resetting the system using the CLIProcedure 26 Resetting the system using the EMS Canopy T1/E1 Multiplexer in T1/E1 Loopback mode T1/E1 Loopback Procedure 27 Invoking a T1/E1 loopback using the CLI Invoking a T1/E1 Loopback using the CLIInvoking a T1/E1 Loopback Using the EMS Procedure 28 Invoking a T1/E1 loopback using the EMS Comparison of diagnostic measurements Measurements from DiagnosticsFirmware Upgrades Procedure 29 Upgrading firmware Fpga revision details screen End of procedure Click Download License KEY Upgrades T1/E1 Port Upgrade window Invalid key entry window Terms of Warranty Software License Terms and Conditions Canopy T1/E1 Multiplexer Hardware Warranty in U.S Obtaining Technical Support Invoking Your Warranty Rights Enter get canopy port auto negotiation CLI Commands to GET Status InformationDesired Action Syntax, Response, and Description Enter get lan port auto negotiation Enter get line 1/2/3/4 length Enter get code line 1/2/3/4 Enter get clock source Enter get master clock reference lineEnter get secondary clock reference line Enter get loopback line 1/2/3/4 Enter get firmware revision Regulatory Compliance Information European Telecommunications Standards Institute TRADEMARKS, Product NAMES, and Service NamesDepartment of Communications Canada Canadian Compliance Statement References