NAP-200-008

Sheet 4/10

Switch Setting of Circuit Card

Table 008-4 PN-CP03 (MP) Card Switch Settings (Continued)

SWITCH NAME

SWITCH

SETTING

FUNCTION

CHECK

NUMBER

POSITION

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

SW2 (Piano Key SW)

 

• When using the PLO card (PN-CK00):

 

OFF

 

 

 

 

 

 

 

 

 

SW2-2

SW2-3

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

2, 3

OFF

ON

 

 

 

 

 

 

 

 

 

 

 

 

 

4

 

 

 

 

 

 

 

 

 

• When not using the internal PLO and the PLO card:

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

3

 

 

 

 

 

 

 

 

 

 

 

 

 

2

 

 

 

 

 

 

 

 

 

 

SW2-2

SW2-3

 

 

 

 

 

 

 

 

 

 

 

 

1

 

 

 

 

 

 

 

 

 

 

OFF

OFF

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

ON

When using RS1 port for built-in

 

 

 

 

 

ON

 

 

 

 

 

 

 

 

 

 

 

 

 

 

4

MODEM.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

OFF

When using RS1 port for RS-232C.

 

 

VR (Rotary SW)

 

Variable Resistor for External Hold Tone

 

 

Source

20

 

(0 - 20 KΩ: Clockwise)

0

 

 

JP0 (Jumper pin)

 

For normal operation

 

UP

Note: Do not remove this jumper. The

 

power to RAM will be removed

 

 

 

 

causing loss of Office Data Pro-

 

 

gramming.

Front

Not used

DOWN

JP1 (Jumper pin)

 

For normal operation

 

 

 

 

 

UP

Note: Do not relocate this jumper when

 

 

 

 

 

 

 

 

 

 

 

power is turned on.

 

 

 

 

 

 

 

 

 

 

 

Front

DOWN

For using External Tone Source

 

 

 

 

 

 

 

 

 

 

The figure in the SWITCH NAME column and the position in in the SETTING POSITION col- umn indicate the standard setting of the switch. When the switch is not set as shown by the figure and , the setting of the switch varies with the system concerned.

Note: Set the groove on the switch knob to the desired switch position.

CHAPTER 3

NDA-24219

Page 108

Revision 2.0

Page 122
Image 122
NEC NEAX1000IVS system manual Modem OFF, Down