Manuals / Brands / Car Audio and Video / Car Satellite Radio System / NEC / Car Audio and Video / Car Satellite Radio System

NEC NEAX1000IVS (16) Message Center Interface Connection for VM00 to AP00 (see Figure 007-43)

1 160

Download 160 pages, 2.04 Mb

CHAPTER 3 NDA-24219

Page 104

Revision 2.0

NAP-200-007

Sheet 55/55

Termination of Cables on MDF

(16) Message Center Interface Connection for VM00 to AP00 (see Figure 007-43)

Figure 007-43 Message Center Interface Connection for VM00 to AP00

Note

08 09

Dterm

APR

APR in Dual Port Mode

for Single Line Interface

Note: For Dual Port Mode, assign upper 4 LENs of 8DLCJ in LT08 and lower 4 LENs in Virtual Slot for

APR Extension.

VIRTUAL SLOT

0706

050403020100

COM 2

COM 1

PN-VM00

AD-8

Voice Mail

Note

AP VM-0.7 CA-A

LTC 1

PIM ABA-UA

25 T0 50 R0 to Internal Modem of VM

Connection to Internal

Modem of AD-8 Voice Mail

Maintenance Console

25 PIN D-SUB

CONNECTOR

CUSTOMER

PROVIDED

CABLE

RS RVS4S CA

or MAT CA-P

for Voice Mail

Contents

Main Page NEAX1000 IVS Very Small Platform System Manual NEAX2000 IVS Family of Products TABLE OF CONTENTS Page TABLE OF CONTENTS (CONTINUED) Page LIST OF FIGURES Figure Title Page LIST OF FIGURES (CONTINUED) Figure Title Page LIST OF TABLES LIST OF TABLES Table Title Page REGULATORY INFORMATION Page Page Page Page Page CHAPTER 1 INTRODUCTION CHAPTER 1 NDA-24219 Page 2 Figure 1-2 Scope of Installation Procedures NDA-24219 CHAPTER 2 Page 3 CHAPTER 2 GENERAL INFORMATION Figure 2-1 PBX Trunking Diagram 1. TRUNKING DIAGRAM Figure 2-1 shows a typical trunking diagram for the PBX. Page Page Page Page Page Page Page Page Page Page Page Page * The value in the [ ] shows the cable length when using the long line function. Page Page CHAPTER 3 INSTALLATION PROCEDURE Page Page Page Page CHAPTER 3 NDA-24219 Page 24 Figure 3-2 Procedure Flowchart Page Page Page CHAPTER 3 NDA-24219 Page 28 NAP-200-002 Sheet 1/2 Marking and Drilling Figure 002-1 Wall Mounting Points 3. DRILLING Install anchor bolts as shown in Figure 002-2. Page Page (3) After hanging PIM onto the wall, tighten each M4 machine screw using a phillips screw driver. Page Page Page Page 4. AC POWER CABLING (1)The cable connections on the PZ-PW86/PW112 card are shown in Figure 003-7. turning on the SW switch. CHAPTER 3 NDA-24219 Page 38 NAP-200-003 Sheet 9/12 Installation of Main Equipment Figure 003-7 Cable Connection on PZ-PW86/PW112 (Continued) Note 1 CAUTION: Set the appropriate volt- age before turning on the SW switch. NDA-24219 CHAPTER 3 Page 39 NAP-200-003 Sheet 10/12 Installation of Main Equipment Figure 003-7 Cable Connection on PZ-PW86/PW112 (Continued) PZ-PW112 Page Page Note:For details of battery connection, see NAP- 200-004. Page Page Page Page Page Page Page Page CHAPTER 3 NDA-24219 Page 52 Sheet 3/55 Figure 007-3 LTC Connector Pin Arrangement (3) Figure 007-3 shows the LTC connector pin arrangement. PIM0 * When AD8 is mounted in LT00, pins 25 and 50 of LTC1 bring out the AD8 internal modem leads. NDA-24219 CHAPTER 3 Page 53 Sheet 4/55 PIM1 Figure 007-3 LTC Connector Pin Arrangement (Continued) CHAPTER 3 NDA-24219 Page 54 Sheet 5/55 2.MDF CROSS CONNECTIONS Table 007-2 shows the cross connections on the MDF for LTC0 and LTC1. Table 007-2 LTC0 and LTC1 MDF Cross Connection Information Page CHAPTER 3 NDA-24219 Page 56 Sheet 7/55 Table 007-2 LTC0 and LTC1 MDF Cross Connection Information (Continued) * Major and minor alarm connections are used for external indications. CHAPTER 3 NDA-24219 Page 58 Sheet 9/55 Figure 007-4 MDF Cross Connection for 4 Line C.O. Trunk Card (PN-4COT) (1) C.O. Trunk (a) 4 Line C.O. Trunk (PN-4COT) (see Figure 007-4) 1R026T0 2R127T1 3R228T2 4R329T3 26 T0 1 R0 27 T1 2 R1 28 T2 3 R2 29 T3 4 R3 NDA-24219 CHAPTER 3 Page 59 Sheet 10/55 (b) 8 Line C.O. Trunk (PN-8COT) (see Figure 007-5) CHAPTER 3 NDA-24219 Page 60 Sheet 11/55 Figure 007-6 MDF Cross Connection for 4W E&M Trunk Card (PN-2ODT) (2) Tie Line Trunk (a) 4W E&M Trunk (PN-2ODT) (see Figure 007-6) Page CHAPTER 3 NDA-24219 Page 62 Sheet 13/55 Figure 007-7 MDF Cross Connection for 2W E&M Trunk Card (PN-2ODT) (b) 2W E&M (PN-2ODT) (see Figure 007-7) Page CHAPTER 3 NDA-24219 Page 64 Sheet 15/55 Figure 007-8 MDF Cross Connection for 2 Line DID Trunk Card (PN-AUCA) (3) DID Trunk (a) 2 Line DID Trunk (PN-AUCA) (see Figure 007-8) NDA-24219 CHAPTER 3 Page 65 Sheet 16/55 Figure 007-9 MDF Cross Connection for 4 Line DID Trunk Card (PN-4DITB) (b) 4 Line DID Trunk (PN-4DITB) (see Figure 007-9) CHAPTER 3 NDA-24219 Page 66 Sheet 17/55 Note: The same connection is required when using PN-4LC. Figure 007-10 MDF Cross Connection for Single Line Telephone (Standard Line) (4) Single Line Telephone (a) Standard Line (PN-8LC) ( se e Figure 007-10) NDA-24219 CHAPTER 3 Page 67 Sheet 18/55 Figure 007-11 MDF Cross Connection for Single Line Telephone (Long Line) (b) Long Line (PN-AUCA) (see Figure 007-11) CHAPTER 3 NDA-24219 Page 68 Sheet 19/55 Note: The same connection is required when using PN-4DLCD. Figure 007-12 MDF Cross Connection for Multiline Terminal/DSS Console (Standard Line) (5) Multiline Terminal/DSS Console (a) Standard Line (PN-8DLC) (see Figure 007-12) NDA-24219 CHAPTER 3 Page 69 Sheet 20/55 Figure 007-13 MDF Cross Connection for Multiline Terminal/DSS Console (Long Line) (b) Long Line (PN-2DLCB/N) (see Figure 007-13) Page set and then plug the modular cord to the jack set as shown in Figure 007-15. Page Page For the MDF cross connection for the SN610 ATTCON, refer to Figure 007-17. NDA-24219 CHAPTER 3 Page 75 Sheet 26/55 Figure 007-18 MDF Cross Connection for SN610 ATTCON (b) MDF Cross Connection (see Figure 007-18) CHAPTER 3 NDA-24219 Page 76 Sheet 27/55 Figure 007-19 MDF Cross Connection for Day/Night Mode Change by External Key (7) Day/Night Mode Change by External Key (see Figure 007-19) (8) External TAS Indicator (a) Outline of the Connection (see Figure 007-20) CHAPTER 3 NDA-24219 Page 78 Sheet 29/55 Figure 007-21 MDF Cross Connection for TAS Indicator with Battery (b) MDF Cross Connection When using a TAS Indicator with a Battery (see Figure 007-21) NDA-24219 CHAPTER 3 Page 79 Sheet 30/55 Figure 007-22 MDF Cross Connection for TAS Indicator with Battery (Ground Start) When using a TAS Indicator with a Battery (Ground Start) (see Figure 007-22) Page NDA-24219 CHAPTER 3 Page 81 Sheet 32/55 Figure 007-24 MDF Cross Connection for Paging Equipment (b) MDF Cross Connection (see Figure 007-24) Page (a) Outline of the Connection (see Figure 007-25) When using PN-4COT / 8COT and PN-DK00 When using Pin Jacks on PN-TNTA When using Pin Jack on PN-CP03 CHAPTER 3 NDA-24219 Page 84 (b) MDF Cross Connection (see Figure 007-26) Page Page NDA-24219 CHAPTER 3 Page 87 Sheet 38/55 Figure 007-28 MDF Cross Connection for External BGM Sources (b) When using Pin Jacks on PN-TNTA (see Figure 007-29) Page CHAPTER 3 NDA-24219 Page 90 Sheet 41/55 Figure 007-31 MDF Cross Connection for PFT (PN-AUCA) Page (b) When using PZ-8PFTA card Figure 007-32 shows an outline of a PFT (PZ-8PFTA) connection. the mounting bracket and secure it the screws provided. Install the PZ-8PFTA card to the PIM according to the following steps. card as shown in Figure 007-34. Then, secure them to each other using screws and tie wraps. NDA-24219 CHAPTER 3 Page 95 Sheet 46/55 Figure 007-35 PFT Connector Pin Assignment Figure 007-35 shows the PFT connector pin assignment for each PFT circuit number (No. 0 - No. 7). CHAPTER 3 NDA-24219 Page 96 Sheet 47/55 Figure 007-36 MDF Cross Connection for PFT (PZ-8PFTA) NDA-24219 CHAPTER 3 Page 97 Sheet 48/55 Figure 007-36 MDF Cross Connection for PFT (PZ-8PFTA) (Continued) (13) Alarm Display Panel Figure 007-37 shows the cross connection for an Alarm Display Panel. Page Page (b) MDF Cross Connection with AC Adapter Power Option (see Figure 007-40) CHAPTER 3 NDA-24219 Page 102 Sheet 53/55 Figure 007-41 MDF Cross Connection via PN-PW00 Power Option (c) MDF Cross Connection via PN-PW00 Power Option (see Figure 007-41) Page CHAPTER 3 NDA-24219 Page 104 Sheet 55/55 Figure 007-43 Message Center Interface Connection for VM00 to AP00 (16) Message Center Interface Connection for VM00 to AP00 (see Figure 007-43) Page 2. PN-CP03 (MP) (1) Locations of Lamps, Switches, and Connectors (see Figure 008-1) (2) Lamp Indications (see Table 008-3) (3) Switch Setting (see Table 008-4) The figure in the SWITCH NAME column and the position in in the SETTING POSITION col- DOWN NDA-24219 CHAPTER 3 Page 109 Figure 008-2 PZ-PW86 (PWR) Card PZ-PW86(C) (2) Lamp Indications (see Table 008-5) PZ-PW86(D) (3) Switch Settings (see Table 008-6) The figure in the SWITCH NAME column and the position in in the SETTING POSITION col- OFF SW1 SW301 Page (2) Lamp Indications (see Table 008-7) (3) Switch Settings (see Table 008-8) The figure in the SWITCH NAME column and the position in in the SETTING POSITION col- Page Page Page Page Page Page Page Page Set the switches on the MP card as shown in Figure 0010-2. Page Page Page Page Page Page CHAPTER 4 OFFICE DATA PROGRAMMING Page Page Page Page CHAPTER 4 NDA-24219 Page 134 PN-2DAT Card number must be assigned to 1st LEN (LEVEL PN-8RST Card number must be assigned to 1st LEN (LEVEL Note: When using the internal DTMF Receiver on the MP card, assign Card No. E200 to LEN No. 0124. PN-DK00 Card number must be assigned to 1st LEN (LEVEL NDA-24219 CHAPTER 4 Page 135 PN-CFT Card number must be assigned to 1st LEN (LEVEL 0) of each LT slot. PN-TNT Card number must be assigned to 1st LEN (LEVEL CARD TO BE CHAPTER 4 NDA-24219 Page 136 CARD TO BE Page 1.3.2 Station Data 1.3.3 Trunk Data 1.3.4 Station Hunting Group Data Page Page NDA-24219 CHAPTER 4 Page 143 1.4 System Configuration 1.4.1 Port Assignment Table Table 4-9 Port Assignment Table Page 1.4.3 Quantity Table for Circuit Cards (CARD NAME)