NEC NEAX1000IVS system manual SPN-4RSTB-911, PN-M03

NAP-200-007

Sheet 2/55

Termination of Cables on MDF

(2)Figure 007-2shows the relationship between each Line Equipment Number (LEN) and each Card Slot Number (LT Number).

	Note 1				Note 2		Note 3
	0127	0071	0079	0087	0095		0103		0111
	0126	0070	0078	0086	0094		0102		0110
	0125	0069	0077	0085	0093		0101		0109
	0124	0068	0076	0084	0092		0100		0108	LEN
PIM 1	0123	0067	0075	0083	0091	0095	0099	0103	0107	(LINE EQUIPMENT NUMBER)
	0122	0066	0074	0082	0090	0094	0098	0102	0106
	0121	0065	0073	0081	0089	0093	0097	0101	0105
	0120	0064	0072	0080	0088	0092	0096	0100	0104
	(LT00)	(LT01)	(LT02)	(LT03)	(LT04)	(LT05)	(LT06)	(LT07)	(LT08)	CARD SLOT NUMBER
	0063	0007	0015	0023	0031		0039		0047
	0062	0006	0014	0022	0030		0038		0046
	0061	0005	0013	0021	0029		0037		0045
	0060	0004	0012	0020	0028		0036		0044	LEN
PIM 0	0059	0003	0011	0019	0027	0031	0035	0039	0043	(LINE EQUIPMENT NUMBER)
	0058	0002	0010	0018	0026	0030	0034	0038	0042
	0057	0001	0009	0017	0025	0029	0033	0037	0041
	0056	0000	0008	0016	0024	0028	0032	0036	0040
	(LT00)	(LT01)	(LT02)	(LT03)	(LT04)	(LT05)	(LT06)	(LT07)	(LT08)	CARD SLOT NUMBER
	Note 1				Note 2		Note 3

Note 1: Do not mount line/trunk circuit card with cabling in this slot; this slot has no connection to the MDF via the backplane (LTC cables).

Note 2: When an 8-port line/trunk card, which requires cabling to MDF, is mounted in Slot 04, Slot 05 must be left vacant or mounted with circuit cards1 that do not interfere with the 8-port card mounted in LT04.

Note 3: When an 8-port line/trunk card, which requires cabling to MDF is mounted in SLot 06, Slot 07 must be left vacant or mounted with circuit cards1 that do not interfere with the 8-port card mounted in LT06.

Note 4: When using internal DTMF Receiver (4RST) on MP card, assign Card No. E200 to LEN No. 0124.

Note 5: If single-line cards are mounted in LT or LT/AP slots, an external ring generator must be connected to PWR0B. The system power supply does not provide these voltages. It is recommended that the APR adapter be used in dual-port mode to provide for single-line devices.

1When an 8-port card is mounted in Slot 04/06, Slot 05/07 can only be mounted with the following cards:

SPN-AP00	SPN-AP01	SPN-ME00	SPN-SC01
SPN-SC02	SPN-4RSTB	SPN-4RSTB-911	SPN-4RSTC
SPN-CK00	SPN-CC00	PN-M03	SPN-SC03 (CSH)/(ICH)

Figure 007-2 Location of Each LEN
NDA-24219	CHAPTER 3
	Page 51
	Revision 2.0