Roland VC-2 owner manual Bass Multi, 36 E.Piano Multi

Effects List

35: Bass Multi
			Parameter	Value		Description
Bass Multi provides Comp/Limiter, Overdrive or Distortion,			Mod Xover-	500–15000 Hz,		Adjusts the cutoff frequency of the
			LPF	THRU		low pass filter. (THRU: no filter is
3-band equalizer, and Chorus or Flanger effects connected in
						used)
series. This algorithm is a multi-effects for bass.
			Mod Xover-	THRU,		Adjusts the cutoff frequency of the
			HPF	50–800 Hz		high pass filter. (THRU: no filter is
Parameter	Value	Description
						used)
Comp Sw	OFF, ON	Turns the comp/limiter on/off.
			Mod Level	0–127		Volume of the chorus or flanger
Comp	-60–0 dB	Sets the volume level at which the
						sound.
Threshold		compression begins.
Comp Attack	0–127	Sets the time after the sound vol-	36: E.Piano Multi
		ume is crossed the compressor
		threshold until compression be-	Enhancer, Phaser, Chorus or Flanger, and Tremolo or Auto-
		gins.
Comp Re-	0–127	Specifies the time from when the	pan are connected in series. This effect is used for electric
lease		volume drops below the compres-	piano.
		sor threshold until compression is
		no longer applied.	Parameter	Value	Description
Comp Ratio	1.5:1, 2:1, 4:1,	Sets the “source sound:output	Enhan Sw	OFF, ON	Turns the enhancer effect on/off.
	100:1	sound” compression ratio.	Enhan Sens	0–127	Sensitivity of the enhancer
Comp Gain	-60– +12 dB	Adjusts the output gain.
			Enhan Fre-	0–127	Sets the lower limit of the frequencies
Od/Ds Sw	OFF, ON	Selects whether to use overdrive	quency		to which the enhancement effect is
		or distortion.			added.
Drive Mode	OD, DS	Selects whether to use overdrive	Enhan Mix	0–127	Level of the overtones generated by
		(OD) or distortion (DS).	Level		the enhancer
Drive	0–127	Degree of distortion	Enhan Lev-	0–127	Volume of the enhancer sound
Amp Sim Sw	OFF, ON	Turns the amp simulator on/off.	el
			Phaser	0–127	Specifies the center frequency at
Amp Type	SMALL,	Type of guitar amp
			Manual		which the sound is modulated.
	BUILT-IN,	SMALL: small amp
	2-STACK	BUILT-IN: single-unit type amp	Phaser Rate	0.05–10.0	Specifies the frequency of modula-
	(STACK)	2-STACK: large double stack amp		Hz, note	tion.
Distortion	0–127	Volume of the overdrive or distor-	Phaser	0–127	Specifies the depth of modulation.
(DS) Level		tion sound.	Depth
EQ Low Freq	50–4000 Hz	Frequency of the low range	Phaser Res-	0–127	Specifies the amount of feedback for
EQ Low Gain	-15– +15 dB	Gain of the low range	onance		the phaser.
					Higher settings will give the sound a
EQ Mid Freq	50–20000 Hz	Frequency of the middle range
					stronger character.
EQ Mid Q	0.5, 0.7, 1.0, 2.0,	Gain of the middle range
			Phaser Mix	0–127	Specifies the volume of the phase-
	4.0, 8.0	Set a higher value for Q to narrow
			Level		shifted sound, relative to the direct
		the range to be affected.
					sound.
EQ Mid Gain	-15– +15 dB	Gain of the middle range
			Mod Mode	CHORUS,	Selects whether to use chorus or
EQ Hi Freq	2000–20000 Hz	Frequency of the high range		FLANGER	flanger.
EQ Hi Gain	-15– +15 dB	Gain of the high range	Mod Rate	0.05–10.0	Adjusts the speed of modulation for
Mod Mode	CHORUS,	Selects whether to use chorus or		Hz, note	the chorus or flanger.
	FLANGER	flanger.	Mod Depth	0–127	Adjusts the depth of modulation for
Mod Rate	0.05–10.0 Hz,	Adjusts the speed of modulation			the chorus or flanger.
	note	for the chorus or flanger.	Mod Phase	0–180 deg	Sets how the chorus or flanger sound
Mod Depth	0–127	Adjusts the depth of modulation			is spread.
		for the chorus or flanger.	Mod Pre	0–50.0 ms	Adjusts the delay time from the direct
Mod Phase	0–180 deg	Sets how the chorus or flanger	Delay		sound until the chorus or flanger
		sound is spread.			sound is heard.
			Mod Feed-	-98– +98 %	Adjusts the proportion of the effect
Mod Pre De-	0–50.0 ms	Adjusts the delay time from the di-
lay		rect sound until the chorus or	back		sound that is fed back into the effect.
		flanger sound is heard.			Negative (-) settings will invert the
					phase.
Mod Feed-	-98– +98 %	Adjusts the proportion of the ef-
			Mod Xover-	500–15000	Adjusts the cutoff frequency of the
back		fect sound that is fed back into the
		effect. Negative (-) settings will in-	LPF	Hz, THRU	low pass filter. (THRU: no filter is
		vert the phase.			used)
			Mod Xover-	THRU, 50–	Adjusts the cutoff frequency of the
			HPF	800 Hz	high pass filter. (THRU: no filter is
					used)

58