8. Appendix B: LUFP7 Gateway GSD File
; Supported baudrates
9.6_supp | = 1 |
19.2_supp | = 1 |
45.45_supp | = 1 |
93.75_supp | = 1 |
187.5_supp | = 1 |
500_supp | = 1 |
1.5M_supp | = 1 |
3M_supp | = 1 |
6M_supp | = 1 |
12M_supp | = 1 |
Communication rates supported by the LUFP7 gateway.
All rates should be mentioned in this section. The gateway supports all the baud rates of the
; Maximum responder | time for supported baudrates | Maximum response time of the gateway, | ||||
MaxTsdr_9.6 |
| = 60 |
| |||
|
| depending on the baud rate of the | ||||
MaxTsdr_19.2 |
| = 60 |
| |||
MaxTsdr_45.45 |
| = 60 |
|
| ||
MaxTsdr_93.75 |
| = 60 |
|
|
|
|
MaxTsdr_187.5 |
| = 60 |
| The response times specified for the | ||
MaxTsdr_500 |
| = 100 |
| |||
MaxTsdr_1.5M |
| = 150 |
| gateway are standard values, compatible | ||
MaxTsdr_3M |
| = 250 |
| with | the TSX PBY 100 | coupler, for |
MaxTsdr_6M |
| = 450 |
| example. |
| |
MaxTsdr_12M |
| = 800 |
|
|
|
|
; Supported hardware features |
|
|
|
| ||
Redundancy |
| = 0 | ; not supported | General hardware characteristics specific | ||
Repeater_Ctrl_Sig | = 2 | ; TTL | to |
| ||
24V_Pins |
| = 0 | ; not connected |
| ||
Implementation_Type | = "SPC3" |
|
|
|
| |
; Supported DP features |
|
|
|
| ||
Freeze_Mode_supp | = 1 | ; supported | Supported and not supported | |||
Sync_Mode_supp |
| = 1 | ; supported | services. |
| |
Auto_Baud_supp |
| = 1 | ; supported |
| ||
Set_Slave_Add_supp | = 0 | ; not supported |
|
|
| |
; Maximum polling frequency |
| Maximum polling frequency / Minimum | ||||
Min_Slave_Intervall | = 1 | ; 100 us | polling interval |
| ||
|
|
|
| 100 µs is the smallest interval that can be | ||
|
|
|
| configured. |
| |
; Maximum supported | sizes | ; modular | The | LUFP7 gateway is | a modular | |
Modular_Station | = 1 | |||||
Max_Module |
| = 24 |
| |||
Max_Input_Len |
| = 244 |
| exchanges on the | ||
Max_Output_Len |
| = 244 |
| configured by combining several modules | ||
Max_Data_Len |
| = 416 |
| together (see below). |
| |
Modul_Offset |
| = 1 |
|
| ||
|
|
|
|
| ||
Fail_Safe |
| = 0 | ; state CLEAR not accepted | Supported and not supported | ||
Slave_Family |
| = 0 |
| services (cont'd). |
| |
|
| The length of the gateway's diagnostic data | ||||
Max_Diag_Data_Len | = 6 |
| should remain equal to 6. N.B. there are no | |||
|
|
|
| |||
|
|
|
| parameter data (the “User_Prm_Data_Len” | ||
|
|
|
| and | “User_Prm_Data” parameters are | |
|
|
|
| therefore omitted). |
| |
Bitmap_Device | = "LUFP7_R" |
| Names of the bitmap files used by SyCon | |||
Bitmap_Diag | = "LUFP7_D" |
| to display the gateway's connection | |||
Bitmap_SF | = "LUFP7_S" |
| status. |
| ||
; Definition of modules |
| Beginning of the section where the | ||||
|
|
|
| modules used for configuring the sizes of | ||
|
|
|
| the gateway inputs and outputs are | ||
|
|
|
| defined. |
| |
92
