Introduction, Presentation, Notation | Schneider Electric VW3A3310d

4. Introduction

4. 1. Presentation

The Ethernet card (catalog number VW3A3310d) is used to connect an Altivar 61 / 71 drive to an Ethernet network using the Modbus TCP/IP protocol and Transparent Ready services.

The VW3A3310d card is equipped with two shielded RJ45 Ethernet connectors.

The accessories for connection to the Ethernet network must be ordered separately.

The data exchanges permit the following drive functionality:

•Configuration

•Adjustment

•Control

•Monitoring

•Diagnostics

The standard web server (English only) provides access to the following pages:

•Altivar Viewer

•Data Viewer

•Ethernet

•Security

The standard web server can be adapted or replaced by a customized server depending on the requirements of the application.

The graphic display terminal or the integrated display terminal can be used to access numerous functions for communication diagnostics.

4. 2. Notation

Drive terminal displays

The graphic display terminal menus are shown in square brackets.

Example: [1.9 COMMUNICATION].

The integrated 7-segment display terminal menus are shown in parentheses.

Example: (COM-).

The parameter names displayed on the graphic display terminal are shown in parentheses.

Example: [Fallback speed].

The parameter codes displayed on the integrated 7-segment display terminal are shown in round brackets. Example: (LFF).

Formats

Hexadecimal values are written as follows: 16#

Binary values are written as follows: 2#

8

Image 8

Schneider Electric VW3A3310d user manual Introduction, Presentation, Notation

Contents

Altivar 61 Page Table of contents Table of contents Important Information Please Note Before you begin Hazard of Electric SHOCK, EXPLOSION, or ARC Flash Installation Manual Documentation structureProgramming Manual ATV61 Notation IntroductionPresentation Hardware setup Installing the card in the driveReceipt Hardware description Connecting to the Ethernet network Card RJ45 connector pinoutPin Signal Example of connection to an Ethernet network Ethernet network connection elements Access to Ethernet menu via graphic display terminal Access to Ethernet menu via the integrated display terminalEthernet menu ENT Ethernet menu parameters Code Description IPP IPP1 0.0.0 0 0 0 IPP2 IPP3IPP4 IPF FdrA FdrSFdrt FdrE Configuration List of functions to be configured Configuring IP addresses Power-up InitializationAssigning IP addresses Static Addressing Dynamic Configuring Bootp Configuring FDREntering IP addresses in the terminal IP card IPC1 IPC2 IPC3 IPC4 IP Mask IPM1 IPM2 IPM3 IPM4 Configuring IO Scanning Reserving control Configuring the control Control via Ethernet in I/O profileControl via Ethernet or the terminals in I/O profile Parameter Value Comment Control via Ethernet in CiA402 Drivecom profile Control via Ethernet or the terminals in CiA402 profile Profile Separate Configuring communication interruption management Communication monitoringNetwork management Communication COM. Fault Management External FaultDrive response RDY NET Configuring monitored parameters Format Range Terminal display Color/ state Description DiagnosticsSignalling LEDs Available information Monitoring the controlIntegrated display Terminal Workshop Web server Troubleshooting communication interruptions Ethernet communication interruption typeExtended communication interruption Code Troubleshooting the card Software setup List of services supportedClient Service Number of connections TCP connections Unit ID Modbus TCP server Accessible parameters Modbus TCP serverModbus TCP frames Drive Modbus servers Address Size Description Access Possible values, comments Ethernet card parametersIPC1.IPC2.IPC3.IPC4 IPM1.IPM2.IPM3.IPM4 IPP1.IPP2.IPP3.IPP4 IPF1.IPF2.IPF3.IPF4 FDR autosave List of Modbus functions supported Read Holding Registers 3 functionCode Modbus name Description Size of data Decimal Byte Meaning Write Single Register 6 function Write Multiple Registers 16 = 16#10 function Read/Write Multiple Registers 23 = 16#17 function 16#17 Read Device Identification 43 = 16#2B function Bytes Meaning With the VW3A3310d Ethernet card IO Scanning service Periodic variables Address Description Default value Address table FDR service Local configuration Downloaded configuration Drive parameters configurationFirst use IP assignment Save Downloading Save the drive configuration parameters in the FDR server Replacing a driveDownload the IP addresses Check that the system is operational Other commands Configuration filePeriodic saving Limitations Home menu Monitoring menu Diagnostics menu Setup menu Security submenu Documentation menuStandard web server Web server functions Applets Access to the web server Username and password Monitoring menu Web server user interfaceHome menu Altivar Viewer Data Viewer Altivar Chart Diagnostics menu Setup menu Ethernet Statistics Http password and Data write password pages FDR Agent Lcfg = No nO Local Config File ErrorError Code Restore Counter IO Scanner Enabling IO Scanning Assigning the IO Scanning periodic variables Time out Master Mail Important Notice Documentation menu Access FTP server Functions File systemFTP functionality Comment DIR Downloading from the web server PrincipleFile management File name 32 characters max Web server Standard web server resources Type File name Size Complete URL BytesType File name Complete URL Bytes Tree structure Snmp agentPresentation ATV Objects Description Access Default valueObjects handled Setup using PL7 Defining the hardware configuration Bootp configuration Multi Configuring Modbus messagingModbus Configuring periodic variables PLC Configuring the Dhcp address server FDR Setup using Concept Setup using ProWORX NxT Hardware configuration Traffic Cop Network configuration TCP/IP configuration O Scanner configuration Page 30072-452-37 2008-02