Profile Separate | Schneider Electric VW3A3310d specification

8. Configuration

b Command in CiA402 (Drivecom) profile via Ethernet and setpoint switching at the terminals

The command comes from Ethernet.

The setpoint comes either from Ethernet or from the terminals. Input LI5 at the terminals is used to switch the setpoint between Ethernet and the terminals.

The command is in CiA402 profile.

Configure the following parameters:

Parameter	Value	Comment
Profile	Separate	The run commands are in CiA402 profile, the command and the setpoint
		can come from different channels.
Setpoint 1 configuration	Network card	Setpoint 1 comes from Ethernet.
Setpoint 1B configuration	Analog input 1 on the terminals	Setpoint 1B comes from input AI1 on the terminals.
Setpoint switching	Input LI5	Input LI5 switches the setpoint (1 ↔1B).
Command 1 configuration	Network card	Command 1 comes from Ethernet.
Command switching	Channel 1	Channel 1 is the command channel.

Note: Setpoint 1B is connected to the functions (summing, PID, etc.), which remain active, even after switching.

Configuration via the graphic display terminal or the integrated display terminal:

	Menu		Parameter	Value
	[1.6	- COMMAND] (CtL-)	[Profile] (CHCF)	[Separate] (SEP)
			[Ref.1 channel] (Fr1)	[Com. card] (nEt)
			[Cmd channel 1] (Cd1)	[Com. card] (nEt)
			[Cmd switching] (CCS)	[Ch1 active] (Cd1)
	[1.7	APPLICATION FUNCT.] (FUn-)	[Ref.1B channel] (Fr1b)	[Ref. AI1] (AI1)
	[REFERENCE SWITCH.]
	[REFERENCE SWITCH.]		[Ref 1B switching] (rCb)	[LI5] (LI5)
			[Ref 1B switching] (rCb)	[LI5] (LI5)

22

Image 22

Contents

Altivar 61 Page Table of contents Table of contents Important Information Please Note Before you begin Hazard of Electric SHOCK, EXPLOSION, or ARC Flash Programming Manual Installation ManualDocumentation structure ATV61 Presentation IntroductionNotation Receipt Hardware setupInstalling the card in the drive Hardware description Pin Signal Connecting to the Ethernet networkCard RJ45 connector pinout Example of connection to an Ethernet network Ethernet network connection elements Ethernet menu Access to Ethernet menu via graphic display terminalAccess to Ethernet menu via the integrated display terminal ENT Ethernet menu parameters IPP4 Code Description IPPIPP1 0.0.0 0 0 0 IPP2 IPP3 IPF Fdrt FdrAFdrS FdrE Configuration List of functions to be configured Assigning IP addresses Configuring IP addressesPower-up Initialization Static Addressing Dynamic Entering IP addresses in the terminal Configuring BootpConfiguring FDR IP card IPC1 IPC2 IPC3 IPC4 IP Mask IPM1 IPM2 IPM3 IPM4 Configuring IO Scanning Reserving control Control via Ethernet or the terminals in I/O profile Configuring the controlControl via Ethernet in I/O profile Parameter Value Comment Control via Ethernet in CiA402 Drivecom profile Control via Ethernet or the terminals in CiA402 profile Profile Separate Network management Configuring communication interruption managementCommunication monitoring Communication Drive response COM. Fault ManagementExternal Fault RDY NET Configuring monitored parameters Format Range Terminal display Signalling LEDs DiagnosticsColor/ state Description Integrated display Available informationMonitoring the control Terminal Workshop Web server Extended communication interruption Troubleshooting communication interruptionsEthernet communication interruption type Code Troubleshooting the card Client Service Number of connections Software setupList of services supported TCP connections Modbus TCP frames Unit ID Modbus TCP server Accessible parametersModbus TCP server Drive Modbus servers IPC1.IPC2.IPC3.IPC4 Address Size Description Access Possible values, commentsEthernet card parameters IPM1.IPM2.IPM3.IPM4 IPP1.IPP2.IPP3.IPP4 IPF1.IPF2.IPF3.IPF4 FDR autosave Code Modbus name Description Size of data Decimal List of Modbus functions supportedRead Holding Registers 3 function Byte Meaning Write Single Register 6 function Write Multiple Registers 16 = 16#10 function Read/Write Multiple Registers 23 = 16#17 function 16#17 Read Device Identification 43 = 16#2B function Bytes Meaning With the VW3A3310d Ethernet card IO Scanning service Periodic variables Address Description Default value Address table FDR service Local configuration First use Downloaded configurationDrive parameters configuration IP assignment Save Downloading Download the IP addresses Save the drive configuration parameters in the FDR serverReplacing a drive Check that the system is operational Periodic saving Other commandsConfiguration file Limitations Standard web server Home menu Monitoring menu Diagnostics menuSetup menu Security submenu Documentation menu Web server functions Applets Access to the web server Username and password Home menu Web server user interfaceMonitoring menu Altivar Viewer Data Viewer Altivar Chart Diagnostics menu Setup menu Ethernet Statistics Http password and Data write password pages FDR Agent Lcfg = No nO Error Code Local ConfigFile Error Restore Counter IO Scanner Enabling IO Scanning Assigning the IO Scanning periodic variables Time out Master Mail Important Notice Documentation menu Access FTP server FTP functionality Comment FunctionsFile system DIR File management Downloading from the web serverPrinciple File name 32 characters max Web server Type File name Standard web server resourcesType File name Size Complete URL Bytes Complete URL Bytes Presentation Snmp agentTree structure Objects handled Objects Description Access Default valueATV Setup using PL7 Defining the hardware configuration Bootp configuration Modbus Configuring Modbus messagingMulti Configuring periodic variables PLC Configuring the Dhcp address server FDR Setup using Concept Setup using ProWORX NxT Hardware configuration Traffic Cop Network configuration TCP/IP configuration O Scanner configuration Page 30072-452-37 2008-02