Schneider Electric VW3A3310d Code Description IPP, IPP1 0.0.0 0 0 0 IPP2 IPP3, IPP4, Ipf, IPF4

7. Ethernet menu

Code	Description
(IPP-)	b [IP Master]
(IPP1)		M [0.0.0.0] (0) (0) (0) (0)
(IPP2)
(IPP3)		IP address of the device that retains control
(IPP4)		Type:	Configuration (read and write)
			Display (read-only) if the address is supplied by a DHCP server
		Possible	• 0 to 255 for each of fields IPP1, IPP2, IPP3 and IPP4.
		values:	• If the value is [0.0.0.0] (0) (0) (0) (0), writing of the control word (CMd) is accepted
				by the Ethernet card regardless of which device has sent it.
			•	If the value is other than [0.0.0.0] (0) (0) (0) (0) only the device which has the IP address
				[IP Master] is authorized to write the control word (CMd).
			Note: This configuration also affects the type of communication monitoring.
		Default value:	[0.0.0.0] (0) (0) (0) (0)
(IPF-)	b [IP FDR]
(IPF1)		M [0.0.0.0] (0) (0) (0) (0)
(IPF2)
(IPF3)		IP address of the FDR server
(IPF4)		Type:	Display (read-only)
		Possible	• 0 to 255 for each of fields IPF1, IPF2, IPF3 and IPF4.
		values:	• If the value is [0.0.0.0] (0) (0) (0) (0), there is no server.
		Default value:	[0.0.0.0] (0) (0) (0) (0)
(ISA)		M [IO Scan.activ.]
		Enable IO Scanner
		Type:	Configuration (read and write)
		Possible	•	[No] (nO): IO Scanner disabled.
		values:	•	[Yes] (YES): IO Scanner enabled.
		Default value:	[Yes] (YES)
(tOUt)		M [time out]
		Ethernet communication monitoring time out
		Type:	Configuration (read and write)
		Possible	•	[0] (0): Monitoring disabled.
		values:	• [0.5 s] (0.5) to [60.0 s] (60.0): Time out value (unit: 0.1 s).
		Default value:	[2.0 s] (2.0)
(FdrU)		M [FDR validation]
		Enable FDR service
		Type:	Configuration (read and write)
		Possible	•	[No] (nO): FDR service disabled.
		values:	•	[Yes] (YES): FDR service enabled.
		Default value:	[Yes] (YES)
(LCFG)		M [FDR Local Config.]
		Selection of local or server configuration
		Type:	Configuration (read and write)
		Possible	• [No] (nO): The drive configuration is downloaded from an FDR server.
		values:	• [Yes] (YES): The drive configuration is local and saved in a FDR server.
		Default value:	[No] (nO)
(FdrF)		M [FDR Error Mgt.]
		Enable FDR file error detection
		Type:	Configuration (read and write)
		Possible	In the event of a problem with the FDR file (missing or invalid):
		values:	• [No] (nO): The Ethernet card does not trigger an [FDR fault] (Fdrd).
			• [Yes] (YES): The Ethernet card triggers an [FDR fault] (Fdrd).
		Default value:	[Yes] (YES)

14