Hardware setup, Receipt | Schneider Electric VW3A3310d guide

5. Hardware setup

5. 1. Receipt

•Check that the card catalog number marked on the label is the same as that on the delivery note corresponding to the purchase order.

•Remove the option card from its packaging and check that it has not been damaged in transit.

CAUTION

STATIC SENSITIVE COMPONENTS

Avoid damage to the Modbus TCP/IP card by electrostatic discharge. Observe the electrostatic precautions below when handling controller circuit boards or when testing components.

Failure to follow these instructions can result in injury or equipment damage.

Observe the following precautions for handling static-sensitive components:

•Keep static-producing material such as plastic, upholstery, and carpeting out of the immediate work area.

•Store the Modbus TCP/IP card in its electrostatic protective packaging when it is not installed in the drive controller.

•When handling the Modbus TCP/IP card, wear a conductive wrist strap connected to the card through a minimum of 1 megohm resistance.

•Avoid touching exposed conductors and component leads with skin or clothing.

5. 2. Hardware description

LEDs

Shielded female RJ45				Shielded female RJ45
Shielded female RJ45				Shielded female RJ45
Ethernet connector				Ethernet connector
(Port 2)		MAC address label		(Port 1)
		MAC address label
		on the Ethernet card

5. 3. Installing the card in the drive

See the ATV61 or ATV71 Installation Manual.

9

Image 9

Schneider Electric VW3A3310d user manual Hardware setup, Receipt, Hardware description, Installing the card in the drive

Contents

Altivar 61 Page Table of contents Table of contents Please Note Important Information Hazard of Electric SHOCK, EXPLOSION, or ARC Flash Before you begin Documentation structure Installation ManualProgramming Manual ATV61 Introduction PresentationNotation Installing the card in the drive Hardware setupReceipt Hardware description Card RJ45 connector pinout Connecting to the Ethernet networkPin Signal Example of connection to an Ethernet network Ethernet network connection elements Access to Ethernet menu via the integrated display terminal Access to Ethernet menu via graphic display terminalEthernet menu ENT Ethernet menu parameters IPP1 0.0.0 0 0 0 IPP2 IPP3 Code Description IPPIPP4 IPF FdrS FdrAFdrt FdrE List of functions to be configured Configuration Power-up Initialization Configuring IP addressesAssigning IP addresses Static Addressing Dynamic Configuring FDR Configuring BootpEntering IP addresses in the terminal IP card IPC1 IPC2 IPC3 IPC4 IP Mask IPM1 IPM2 IPM3 IPM4 Reserving control Configuring IO Scanning Control via Ethernet in I/O profile Configuring the controlControl via Ethernet or the terminals in I/O profile Parameter Value Comment Control via Ethernet or the terminals in CiA402 profile Control via Ethernet in CiA402 Drivecom profile Profile Separate Communication monitoring Configuring communication interruption managementNetwork management Communication External Fault COM. Fault ManagementDrive response RDY NET Format Range Terminal display Configuring monitored parameters Diagnostics Signalling LEDsColor/ state Description Monitoring the control Available informationIntegrated display Terminal Workshop Web server Ethernet communication interruption type Troubleshooting communication interruptionsExtended communication interruption Code Troubleshooting the card List of services supported Software setupClient Service Number of connections TCP connections Modbus TCP server Unit ID Modbus TCP server Accessible parametersModbus TCP frames Drive Modbus servers Ethernet card parameters Address Size Description Access Possible values, commentsIPC1.IPC2.IPC3.IPC4 IPM1.IPM2.IPM3.IPM4 IPF1.IPF2.IPF3.IPF4 IPP1.IPP2.IPP3.IPP4 FDR autosave Read Holding Registers 3 function List of Modbus functions supportedCode Modbus name Description Size of data Decimal Byte Meaning Write Single Register 6 function Write Multiple Registers 16 = 16#10 function 16#17 Read/Write Multiple Registers 23 = 16#17 function Bytes Meaning With the VW3A3310d Ethernet card Read Device Identification 43 = 16#2B function Periodic variables IO Scanning service Address table Address Description Default value FDR service Local configuration Drive parameters configuration Downloaded configurationFirst use IP assignment Save Downloading Replacing a drive Save the drive configuration parameters in the FDR serverDownload the IP addresses Check that the system is operational Configuration file Other commandsPeriodic saving Limitations Setup menu Security submenu Documentation menu Home menu Monitoring menu Diagnostics menuStandard web server Web server functions Applets Username and password Access to the web server Web server user interface Home menuMonitoring menu Altivar Viewer Data Viewer Diagnostics menu Altivar Chart Ethernet Statistics Setup menu Http password and Data write password pages Lcfg = No nO FDR Agent File Error Local ConfigError Code Restore Counter IO Scanner Assigning the IO Scanning periodic variables Enabling IO Scanning Master Time out Important Notice Mail Documentation menu FTP server Access File system FunctionsFTP functionality Comment DIR Principle Downloading from the web serverFile management File name 32 characters max Web server Type File name Size Complete URL Bytes Standard web server resourcesType File name Complete URL Bytes Snmp agent PresentationTree structure Objects Description Access Default value Objects handledATV Defining the hardware configuration Setup using PL7 Bootp configuration Configuring Modbus messaging ModbusMulti Configuring periodic variables PLC Configuring the Dhcp address server FDR Setup using Concept Hardware configuration Traffic Cop Network configuration Setup using ProWORX NxT TCP/IP configuration O Scanner configuration Page 30072-452-37 2008-02