Maintenance 10 Chapter
Message | Meaning and action to take |
|
|
KEY INHI.! 2) | Disc operations are not possible when the |
| DC IN connector is not connected and the |
| |
|
|
ILL. PLAY | An A/V phase error occurred during |
| playback. Stop the disc. |
|
|
Lid Closed! | The lid of the disc compartment does not |
| open. Check the lid. |
|
|
Lid Open! | The lid of the disc compartment is not |
| closed. Close it securely. |
|
|
No Clip! | There are no clips recorded on the disc. |
| Exchange for a recorded disc. |
|
|
No Disc! | There is no disc loaded. Insert a disc and |
| try the operation again. |
|
|
STOP ONCE! | The operation is not possible while the disc |
REC mode! | is being played or recorded. Stop the disc. |
|
|
Disc Top! | The operation is not possible because the |
Disc End! | disc is at the top or end. |
|
|
Formatting! | The disc is being automatically formatted. |
| Wait until the format ends. |
|
|
Live Logg! | The operation you attempted is not |
| possible in Live Logging mode.Turn Live |
| Logging mode off and try again. |
|
|
Recording | The unit is writing to the file system. Wait |
| until writing finishes. |
|
|
No EM Space | Essence marks cannot be inserted. For |
EM Full! | details, see |
| |
SB CLP mode | Try the operation again after pressing the |
| SUB CLIP button to turn off the sub clip |
| indicator. |
|
|
No SEL List | No clip list is selected. Create a new clip |
| list, or load a clip list from the disc. |
|
|
No List! | There is no clip list. Create a clip list. |
|
|
No SUB Clip | There are no sub clips in the clip list. |
| Register a sub clip, or load another clip list. |
|
|
SUB Clip NG | The In and Out point positions are invalid. |
| Set correct In and Out points. |
|
|
MAX# SB CLP | The total number of sub clips is over the |
| upper limit (300). |
|
|
CL OVER DUR | The total duration of sub clips in the current |
| clip list is over the upper limit (24 hours). |
|
|
FAN Stopped! | The main unit or drive fan has stopped. |
Avoid use under high temperatures, turn | |
| off the power, and contact a Sony service |
| representative. |
|
|
MEM REC NG! | (only when |
| Proxy data recording failed because the |
| memory card ran out of memory.Exchange |
| the memory card, and copy the proxy data |
| that could not be recorded. |
|
|
1)“**” indicates the bit rate (50/40/30).
2)REC INHI.! appears if you attempt to start recording.
The following phenomena that may appear in images are specific to CCD (Charge Coupled Device) image sensors. They do not indicate malfunctions.
White flecks
Although the CCD image sensors are produced with high- precision technologies, fine white flecks may be generated on the screen in rare cases, caused by cosmic rays, etc.
This is related to the principle of CCD image sensors and is not a malfunction.
The white flecks especially tend to be seen in the following cases:
•when operating at a high environmental temperature
•when you have raised the master gain (sensitivity)
•when operating in
This product has a compensation function and the problem may be alleviated by automatic black balance adjustment (see page 84).
Vertical smear
When an extremely bright object, such as a strong spotlight or flashlight, is being shot, vertical tails may be produced on the screen, or the image may be distorted.
Monitor screen | Vertical tails shown on the |
image. |
Bright object (e.g. strong spotlight, strong reflected light, flashlight, the sun)
Aliasing
When fine patterns, stripes, or lines are shot, they may appear jagged or flicker.
176