Function | Content |
|
|
TEST OUT | Assigns the function to switch whether or |
CHARACTER | not the characters are mixed to the video |
| signal to be output from the TEST OUT |
| connector. |
|
|
MARKER | Assigns the ON/OFF function to display |
| all markers.1) |
ZEBRA | Assigns the zebra pattern display |
| function to the switch. |
|
|
D5600 | Applies an electrical 5600 K filter. |
|
|
EXT REC | Selects whether or not recording control |
CONTROL | of external devices connected through |
| the CCZ connector |
| is possible. |
|
|
REC VIDEO | Selects which signals you will record |
SOURCE 2) | pictures being shot by the camcorder or |
| video signals from external equipment |
| connected to GENLOCK IN connector. |
|
|
UA01 to UA10 3) | Assigns the items assigned in the |
| ASSIGN SEL menu. |
1)Even when the MARKER item is set to “OFF” on the MARKER page of the USER menu, the ASSIGN 2 switch allows you to display or not to display all markers.
2)When the
3)This does not appear if nothing is assigned in the Assign menu.
Note
For functions that are assigned to the ASSIGN 2 switch, you cannot change those settings using other menus. The function assigned to ASSIGN 2 switch takes precedence over the menu setting.
4 Turn the MENU knob to move the b mark to the item you want to set, and press MENU knob.
The b mark changes to a z mark, and the z mark by the setting changes to a ? mark.
5 Turn the MENU knob to switch to the desired setting, and press the MENU knob.
The z mark changes to a b mark, and the ? mark changes to a z mark, confirming the setting.
6 To continue with other settings, repeat steps 3 and 4.
To return to the previous page
Turn the MENU knob to move the b mark to “ESC” at the right top of the window and press the MENU knob. Alternatively, push the CANCEL/PRST / ESCAPE switch down to the ESCAPE side.
To end the menu operation
Set the MENU ON/OFF switch to OFF or close the cover of the menu operating section.
Operation of the ASSIGN 1/2/3/4 switches when UA01 to UA10 are assigned
When an on/off switchable function (or menu item) is assigned to one of the ASSIGN 1/2/3/4 switches, each time the switch is pressed toggles the function on or off. When another type of menu item is assigned, pressing the switch displays the item and its setting value on the viewfinder screen.
You can then change the setting by pressing and turning the MENU knob.
The viewfinder screen display disappears approximately three seconds after the last operation.
7-3-6 Setting the Date/Time of the Internal Clock
You can set or change the date and time of the internal clock. The date and time set are reflected in the time code. Proceed as follows.
1 Holding down the MENU knob, move the MENU ON/ OFF switch to ON.
The TOP menu appears.
2 Turn the MENU knob to move the b mark to “DIAGNOSIS”, and press the MENU knob.
If this is the first time the DIAGNOSIS menu has been displayed, the CONTENTS page appears. If the menu has been used before, the last accessed page appears.
3 If the CONTENTS page is displayed, turn the MENU knob to move the b mark to “TIME/DATE”, and press the MENU knob to display the TIME/DATE page.
If a different page is displayed, turn the MENU knob until the TIME/DATE page appears, then press the MENU knob to select the page.
|
|
|
|
|
|
| 04 | TIME/DATE |
|
|
|
| ADJUST | : | EXEC |
| |
| HOUR |
| : | 12 |
|
| MIN |
| : | 55 |
|
| SEC |
| : | 58 |
|
| YEAR |
| : | 00 |
|
| MONTH | : | 07 |
| |
| DAY |
| : | 31 |
|
|
|
|
|
|
|
|
|
|
|
|
|
4 Press the MENU knob.
The TIME ADJUST setting window appears.
Settings Detailed and Displays Menu 7 Chapter
135 | |
|
|