Default Hessen Status Bit Assignments

M300EU OPERATING INSTRUCTIONS

M300EU

 

Addendum to M300E/EM Manual P/N 04288

The list of Hessen status flags for the M300EU is different from that of the M300E/EM. The following table replaces Table 6-33 of the M300E/EM Operators Manual (P/N 04288).

 

 

Table 6-8:

Default Hessen Status Bit Assignments

 

 

 

 

 

 

 

 

 

 

 

STATUS FLAG NAME

 

 

DEFAULT BIT ASSIGNMENT

 

 

 

 

 

WARNING FLAGS

 

 

 

 

 

 

 

 

 

 

 

SAMPLE FLOW WARNING

 

 

 

0001

 

 

 

 

 

 

 

 

 

 

 

 

 

BENCH TEMP WARNING

 

 

 

0002

 

 

 

 

SOURCE WARNING

 

 

 

0004

 

 

 

 

 

 

 

 

 

 

 

 

 

BOX TEMP WARNING

 

 

 

0008

 

 

 

 

 

 

 

 

 

 

 

 

 

WHEEL TEMP WARNING

 

 

 

0010

 

 

 

 

 

 

 

 

 

 

 

 

 

SAMPLE TEMP WARNING

 

 

 

0020

 

 

 

 

 

 

 

 

 

 

 

SAMPLE PRESSURE WARNING

 

0040

 

 

 

 

INVALID CONC

 

 

 

 

 

 

 

 

(The Instrument’s Front Panel Display Will Show The

 

0080

 

 

 

 

Concentration As “XXXX”)

 

 

 

 

 

 

 

 

 

OPERATIONAL FLAGS

 

 

 

 

 

In Manual Calibration Mode

 

 

 

0200

 

 

 

 

 

 

 

 

 

 

 

 

 

In Zero Calibration Mode

 

 

 

0400

 

 

 

 

 

 

 

 

 

 

 

 

 

In Span Calibration Mode

 

 

 

0800

 

 

 

 

 

 

 

 

 

 

 

 

 

UNITS OF MEASURE FLAGS

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

UGM

 

 

 

0000

 

 

 

 

MGM

 

 

 

2000

 

 

 

 

 

 

 

 

 

 

 

 

 

PPB

 

 

 

4000

 

 

 

 

 

 

 

 

 

 

 

 

 

PPM

 

 

 

6000

 

 

 

 

 

 

 

 

 

 

 

 

 

SPARE/UNUSED BITS

 

 

 

100, 1000, 8000

 

 

 

 

UNASSIGNED FLAGS (0000)

 

 

AZERO WARN

 

RELAY BOARD WARNING

 

 

 

 

 

 

 

OVEN TEMP WARNING

 

FRONT PANEL WARNING

 

 

 

 

 

 

 

MP CAL

 

ANALOG CAL WARNING

 

 

 

 

 

 

 

PHOTO TEMP WARNING

 

CANNOT DYN ZERO

 

 

 

 

 

 

 

SYSTEM RESET

 

CANNOT DYN SPAN

 

 

REAR BOARD NOT DETECTED

 

INVALID CONC

 

 

 

 

 

 

USER NOTES:

40

05831 Rev. 01

Page 48
Image 48
Teledyne Model 300EU User Notes, M300EU, Default Hessen Status Bit Assignments, 05831 Rev, Addendum to M300E/EM Manual P/N