Teledyne Model 300EU manual M300EU Addendum to M300E/EM Manual, Rev K.6, Table continues

APPENDIX A-2: Setup Variables For Serial I/O, Revision K.6 M300EU Addendum to M300E/EM Manual

APPENDIX A-2: Setup Variables For Serial I/O, Revision K.6

Table A-1: Additional or Changed Setup Variables Relevant to the M300EU, Revision K.6

SETUP VARIABLE		NUMERIC			DEFAULT	VALUE RANGE		DESCRIPTION
		UNITS			VALUE
		Low	Access Level Setup Variables (818 password)
	Same as in the M300E/EM Operators Manual Appendix A (P/N 04906)
STABIL_GAS		—			CO	CO, CO2 , O2		CO2 , O2 not applicable to the M300EU
		Medium Access Level Setup Variables (929 password)
CO_SAMPLE		Samples	4			1–30		Number of samples to take in measure or
								reference mode.
FILT_SIZE		Samples	1000			1–1000		Moving average filter size.
FILT_DELTA		PPM	0.7			1–1000	Absolute change to trigger adaptive filter.
CO_CONST1		—	78.8			100–50000		CO calculation constant.
CO_CONST2		—	1.458			0–10		CO calculation constant.
BENCH_SET		ºC		48		0–100		Optical bench temperature set point and warning
					Warnings:
								limits.
					34–53
WHEEL_SET		ºC		62		0–100		Wheel temperature set point and warning limits.
					Warnings:
					57–67
								ON applies auto-reference offset and dilution
ZERO_APPLY_IN_CAL		—			ON	OFF, ON		factor during zero/span calibration;
								OFF disables both
ZERO_DWELL		Minutes	3			1–60		Dwell time after closing or opening zero scrubber
								valve.
ZERO_SAMPLES		Samples	1000			1–1000	Number of zero samples to average.
ZERO_FILT_SIZE		Samples	5			1–100	Auto-zero offset moving average filter size.
ZERO_LIMIT		Ratio	1.15			0–5		Minimum auto-zero ratio allowed; must be
								greater than this value to be valid.
ZERO_CAL		Ratio	1.18			0.5–5	Calibrated auto-zero ratio.
CO_TARG_ZERO1		Conc.	0			-100.00–999.99		Target CO concentration during zero offset
								calibration of range 1.
CO_TARG_MID1		Conc.	50			0.01–9999.99		Target CO concentration during mid-point
								calibration of range 1.
CAL_BOX_TEMP1		ºC	30			0–100	Calibrated box temperature for range 1.
CO_TARG_ZERO2		Conc.	0			-100.00–999.99		Target CO concentration during zero offset
								calibration of range 2.
CO_TARG_MID2		Conc.	50			0.01–9999.99		Target CO concentration during mid-point
								calibration of range 2.
CAL_BOX_TEMP2		ºC	30			0–100	Calibrated box temperature for range 2.
						Same as
TEST_CHAN_ID		—			NONE	M300E/EM with		Diagnostic analog output ID.
						following addition:
						TEMP4
SAMP_FLOW_SET		cc/m		1800		0–5000		Sample flow warning limits. Set point is not used.
					Warnings:
					1400–2500
				46				Internal box temperature #2/oven set point and
OVEN_SET		ºC			Warnings:	0–100
								warning limits.
					41–51
OVEN_CYCLE		Seconds	10			0.5–30		Internal box temperature #2/oven control cycle
								period.
Table continues

A-8 05924 Rev K.6