Toshiba RAV-SM1404UT-E, RAV-SM1104UT-E, RAV-SP1104AT-E Selection of horizontal discharge position

No.	Item			Outline of specifications		Remarks
12	Louver control	• If there is the locked louver in the unit, [ ] goes on the remote				For the setting
	(Continued)		controller screen.			operation, refer to
		• While the following controls are performed, the louvers operate				[How to set louver
						lock] of Installation
			even if executing the louver lock.
						Manual.
				Control which ignores lock	Objective louver No.
			•	Operation stop	Full-close position
			‚	When heating operation started	Horizontal discharge position
			ƒ	Heating thermo. OFF	Horizontal discharge position
			„	During defrost operation	Horizontal discharge position	It is position check
				Initialize operation	Full-close position
			…			operation and it does
			†	Self-clean operation	Horizontal discharge position	not link with the real
						louver and air
		• The real louver corresponding to the louver No. displayed on the				direction setup
			remote controller screen during setting of louver lock operates			(Illustration on the
			swinging.			remote controller
		<<Selection of horizontal discharge position>>				screen).
		• For the horizontal discharge position, selection of the cold draft-				If selecting the cold
			less (Control for cold air draft) position and smudging-less
			(Control for smudge of ceiling) position is available.			draft-less position,
		• Although “Smudging-less” position has been set at shipment from				effect of the smudg-
			the factory, “Cold draft-less” position can be selected by changing			ing-less weakens.
			[0000 (At shipment)] to [0002] on the Item code (DN) [45].

•To realize “360° discharge”, it is necessary to set “cold draft-less” position.

•When using the optional part “Height adjustment spacer” or installing the unit at position where there is no ceiling, it is recommended to set DN Item code [45] to [0002] to use it at “cold draft-less” position.

13	HA control	1)	This control is connected to TV control or remote start/stop I/F,	In the group opera-
			etc, and start/stop are available by HA signal input from the	tion, use this control
			remote position.	by connecting to
		2)	This control outputs start/stop status to HA output terminal.	either master or
				follower indoor unit.
		3)	I/O specifications conform to JEMA regulations.
		4)	This control outputs [Operation OFF (STOP) signal] to HA output
			terminal while self-cleaning works. However selection of [Operation
			ON (Operating) signal] is possible by changing [0000 (At ship-
			ment)] of Item code (DN) [CC] to [0001]. In this case, if HA is input
			during self-clean operation during operation of the air conditioner,
			the self-clean operation is not performed. (Unit stops.)
14	Frequency	<In case of wired remote controller>		Command frequency
	fixed operation	1)	When pushing [CHK] button for 4 seconds or more, [TEST] is	is approximately [S7]
	(Test run)
			displayed on the display screen and the mode enters in Test run
			mode.
		2)	Push [ON/OFF] button.
		3)	Using [MODE] button, set the mode to [COOL] or [HEAT].
			• Do not use other mode than [COOL]/[HEAT] mode.
			• During test run operation, the temperature cannot be adjusted.
			• An error is detected as usual.
			• A frequency fixed operation is performed.
		4)	After the test run, push [ON/OFF] button to stop the operation.
			(Display in the display part is same as the procedure in Item 1.)
		5)	Push [CHK] button to clear the test run mode.
			([TEST] display in the display part disappears and the status
			returns to the normal stop status.)

– 54 –