Toshiba VF-S11 manual E6581160

E6581160

QTable of input terminal functions 2

	Function	Code	Function	Action
	No.
	34	F+SS3+AD2	Combination of forward run, preset-speed	ON: Simultaneous input from F, SS3 and AD2
			command 3 and acceleration/deceleration 2
	35	R+SS3+AD2	Combination of reverse run, preset-speed	ON: Simultaneous input from R, SS3 and AD2
			command 3 and acceleration/deceleration 2
	36	F+SS4+AD2	Combination of forward run, preset-speed	ON: Simultaneous input from F, SS4 and AD2
			command 4 and acceleration/deceleration 2
	37	R+SS4+AD2	Combination of reverse run, preset-speed	ON: Simultaneous input from R, SS4 and AD2
			command 4 and acceleration/deceleration 2
	38	FCHG	Frequency command forced switching	ON: H(If H = )
				OFF: HOQF
	39	VF2	No.2 Switching of V/F setting	ON: No.2 V/F setting
				(RV=0, H, H, H, H)
				OFF: No.1 V/F setting
				(Set value of RV, XN, XNX, XD, VJT)
	40	MOT2	No.2 motor switching	ON: No.2 motor
			（VF2＋AD2＋OCS2）	(RV=0, H, H, H, H,
				H, H, H, H)
				OFF: No.1 motor (Set value of RV, XN, XNX,
				XD, VJT, CEE, FGE, H, H)
	41	UP	Frequency UP signal input from external contacts	ON: Increase in frequency
	42	DOWN	Frequency DOWN signal input from external	ON: Reduction in frequency
			contacts
	43	CLR	Frequency UP/DOWN cancellation signal input	OFF→ON: Resetting of UP/DOWN frequency by
			from external contacts	means of external contacts
	44	CLR+RES	Combination of frequency UP/DOWN cancellation	ON: Simultaneous input from CLR and RES
7
			and reset by means of external contacts
	45	EXTN	Inversion of trip stop command from external	OFF: G Trip stop
			device
	46	OH	Thermal trip stop signal input from external device	ON: QJ Trip stop
	47	OHN	Inversion of thermal trip stop command from	OFF: QJ Trip stop
			external device
	48	SC/LC	Forced switching from remote to local control	Enabled when remote control is exercised
				ON: Local control (setting of cmod, HOQF and
				H)
				OFF: Remote control
	49	HD	Operation holding (stop of 3-wire operation)	ON: F (forward run)/R: (reverse run) held, 3-wire
				operation
				OFF: Slowdown stop
	50	CMTP	Forced switching of command mode and terminal	ON: Terminal board operation
			board command	OFF: Setting of EOQF
	51	CKWH	Display cancellation of the cumulative power	ON: Monitor display cancellation of the cumulative
			amount (kWh)	power amount (kWh)
	52	FORCE	Forced operation (factory configuration required)	ON: Forced operation mode in which operation is
				not stopped in the event of the occurrence of
				a soft fault (preset speed operation frequency
				15) To use this function, the inverter needs to
				be so configured at the factory.
				OFF: Normal operation
	53	FIRE	Fire-speed control	ON: Fire-speed operation (preset speed operation
				frequency 15)
				OFF: Normal operation

Note. When function 1, 10-12, 15-17, 38, 41-45 or 48 is assigned to an input terminal board, the input terminal board is enabled even if the parameter command mode selection cmod is set at 1 (panel).

66