» Handling the remote control, » Operating Range

Part Names and Functions

» Handling the remote control

•Do not drop or mishandle the remote control.

•Do not get the remote control wet. If the remote control gets wet, wipe it dry immediately.

•Avoid heat and humidity.

•When not using the remote control for a long period, remove the batteries.

•Do not use new and old batteries together, or use different types together.

•Do not take apart the batteries, heat them, or throw them into a fire.

» Operating Range

*Use the remote control within a distance of about 23 ft. (7m)

from the front of the monitor’s remote control sensor and at horizontal an vertical angles of up to approximately 30°.

*The remote control operation may not function if the monitor’s remote control sensor is exposed to direct sunlight or strong artificial light, or if there is an obstacle between the sensor and the remote control.

Approx.

23 ft (7m)

Page 19

Image 19

Vidikron VP-60, VP-42HD, VP-50 owner manual » Handling the remote control, » Operating Range

Contents

Page Table of Contents Introduction Contents of the package » The features you’ll enjoy includeOptions Important Information » Precautions Important Information » Warnings and Safety Precautions » To avoid damage and prolong operating life » Plasma monitor cleaning procedure What is Covered Under the Terms of this Limited Warranty Limited Warranty RIGHTS, Limits and Exclusions Effective Warranty DateLimited Warranty Important Warranty Registration Vidikron Additional Information Ventilation Requirements for enclosure mounting HOW to Attach Options to the Plasma Monitor » Front View Part Names and Functions AUDIO1, AUDIO2, AUDIO3 » Rear View / Terminal BoardExternal Control Y Cb/Pb Rear View / Terminal Board » Remote Control Light Remote ControlDisplays the source settings on the screen Display » Battery Installation and Replacement » Operating Range » Handling the remote control Video Installation » Connecting Your PC or Macintosh Computer Installation » Connecting Your DVD Player » Connecting Your VCR or Laser Disc Player RGB » Pin Assignment and Signal Levels for 15 pin RGB analog » Mute » Power» Volume Basic Operations Basic Operations » Timer OFFTo set the timer off To cancel the off timer » Aspect Ratio Operations Manual Aspect Ratio Controls Aspect Ratio Controls Intelliwide mode Within 3 seconds » Aspect Ratio Operation with Computer Signals Memory. The change is stored until you change it again Change the adjustments or the settings that are storedButton on the remote control to return to the main menu OSD On Screen Display Controls » Menu Operations OSD On Screen Display Controls Adjust Image HD Type Language Adjusting the picture » Picture Adjust MenuUse the and buttons to adjust the contrast Types of picture modes LW BLK1 Example Setting the Factory modeOnce the adjustment is completed To set to Factory Reducing noise in the picture Once the setting is completedTypes of noise reduction See below to set White Balance Adjust Setting the White BalanceAdjusting the color to the desired level Adjusting the white balance Adjust the white balance using the and buttonsChanging the Gamma Curve Gamma Curve settings Making the Dither adjustments Dither settings Adjusting the colorsDiffuse Audio setup menu » Audio Setup MenuTo continue adjusting the audio Color Chart settings Example Setting Audio INPUT1 to Video Setting the allocation of the audio connectorsTo set the Audio INPUT1 to VIDEO2 To continue making other computer image adjustments » Image Options Settings MenuTo select a mode To adjust the vertical position OFF Adjusting the ComputerAdjusting the position of the image Restoring the factory defaults settings Setting the on-screen menu » Setting 1 Settings MenuTo set the Display OSD to OFF BNC Input settings Setting the BNC connectorsTo set the BNC Input mode to Comp OSD Orbiter settings RGB Type modes It is set to RGB and can not be adjustedExample Setting the RGB Type mode to Auto To set the RGB select mode to Auto To set the HD Type mode to 1080B Example Setting the 1080B mode to HD Type modes Setting the Input SkipTo set the Input Skip mode to OFF Input Skip settings Use the and buttons to select ON, then press the Menu button Resetting to the default values Setting the Auto Off for computer images » Setting 2 MenuTo turn the Auto Off function on Setting the picture to suit the movie Power / Standby indicator Perform Steps 1-2 of Pixl PROTECT, then Orbiter Orbiter settings Inverse Adjust the Orbiter function manuallyOrbiter Function settings Perform Steps 1-3 of ORBITER, then Press the Exit button to return to the Pixl Protect screen Setting the time for INVERSE/WHITESetting the time Perform Steps 1-3 of INVERSE, then Image Sweep Example Setting Image Sweep to onPerform Steps 1-3 of Image SWEEP, then Soften Setting the Sidebar Lev. for the sides of the screenSoften settings Press the Exit button to return to the Image Sweep screen Sidebar LEV. settings To adjust the Sidebar LEVUse the and buttons to adjust the Sidebar LEV Setting the screen size for S1/S2 video input Perform the following operations S1/S2 SettingsPLUG/PLAY Settings Black Level settings Perform Steps 1-2 of TIMER, then » Setting 3 MenuUsing the timer Preset Time Hour Preset Time settingsDaylight Saving Time DAY Use the and buttons to select Program Program TimerON/OFF Hour To set the Default Input to VIDEO2 Setting the Default InputUse the and buttons to select VIDEO2 Enabling/disabling the front panel controls Input Select settings→ RGB3 ↔ RGB2 ↔ RGB1 ↔ HD1 ← → RGB3 ↔ RGB1 ↔ HD2 ↔ HD1 ← To set the Control Lock to on Example Setting OFF Perform the following operationsTo set the IR Enable to OFF Control Lock settings To set the Loop OUT to on Loop Out SettingIR Enable settings Loop OUT settings When the ID Number has been set ID Number SettingTo reset back to ALL Press the Clear button ID Number settings Use this feature to configure a 2×2 or 3×3 video wall Video Wall Setting Perform Steps 1-2 of Video WALL, then Set the 2x2 or 3x3 video wall Example SettingSet the position of each display Example Setting Divider Auto ID DISP. ModeVideo Wall Position settings Press the Exit button to return to the Video Wall screen Use Auto ID settings On Delay Power on delay Video Wall On Delay settings LUM SET Link settings Repeat Timer ReptrUse the and buttons to select Reptr Time Divider Source Reptr Time settings To select Deutsch » Language Settings MenuSetting the language for the menus Language settings English German French Spanish Italian » Video Standard Menu Setting the video signal formatTo select 3.58NTSC Once you have checked the frequency » Signal Info. MenuVideo standard formats Communication Parameters External ControlsApplication Connections Unit ID 1 and Unit ID CommandCommunication Format External Controls CMD1 CMD2 LEN Command Reference List Power OFF Power onInput Switch Change Contrast Gain Data Volume Gain DataAudio Mute on Audio Mute OFF Sharpness Gain Data Bright Gain Data Tint Gain Data Color Gain Data White BAL. Select Image MEM. Select Green Gain Data RED Gain Data Blue Gain Data VID NR Mode SET Treble Gain Data Bass Gain Data Aspect Ratio Select Balance Gain Data Shift Gain Data Size Gain Data Clock Gain Data Phase Gain Data OSD ADJ. Gain Data OSD Select Auto OFF Select Cinema Mode SETSidebar LEV. SET Pixl Protect SET 33 RGB3 ADJ. Select Image Sweep SET Inverse SET Audio Select SET Factory RGB Select BNC Select Language Select HD Select100 Frequency Request Video Standard Select101 102 Input Mode Request 103 Video ADJ Request 104 Auto Select Request Model Name Request Failure Mode Request105 Computer input signals supported by this system Table of Signals Supported106 107 Table of Signals Supported PAL625P 109 Troubleshooting 110 Troubleshooting 111 Specifications 112 Specifications 113 Dimensions 114 Dimensions 115 VP-60 RUMA-010550