Manuals / Vidikron / Computer Equipment / Computer Monitor

Vidikron VP-42HD, VP-60, VP-50 Setting the White Balance, Adjusting the color to the desired level

Models: VP-42 VP-50 VP-42HD VP-60

1 117

Download 117 pages 32.87 Kb

Page 37

Setting the White Balance

OSD (On Screen Display) Controls

Setting the White Balance

Use this procedure to set color tone produced by the plasma dis- play.

Example: Setting “6500K”

Press the MENU button on the remote control to display the

MAIN MENU on the screen, then...

1.Use the and buttons to select “PICTURE ADJUST”, then press the MENU button. The “PICTURE ADJUST” screen appears.

2.Use the and buttons to select “WHITE BAL”.

3.Use the and buttons to select “6500K”.

The mode switches as follows when the and buttons are pressed:

5400K 6500K 8500K 9300K

* See below to set “WHITE BALANCE ADJUST”.

	PICTURE ADJUST				2 / 2
	PREVIOUS PG.
	WHITE BAL	:		6500K

	GAMMA CURVE		:	2.2
	DITHER	:		AUTO
	COLOR CHART
	SEL.	ADJ.		EXIT EXIT

36

*If neither the or button is pressed within 5 seconds, the current selection is set and the previous screen reappears.

4. Once the setting is completed...

Press the EXIT button to return to the main menu. To delete the main menu, press the EXIT button once more.

Information

■Setting the color temperature 5400K .................... Redder

6500K	Slightly redder
8500K	Standard (slightly bluer)
9300K	Bluer

■Restoring the factory default settings

Select “FACTORY” under the SETTING 1 menu. Note that this also restores other settings to the factory defaults.

Adjusting the color to the desired level

Use this procedure to adjust the white balance for each color temperature to achieve the desired color quality.

Example: Adjusting the “GAIN RED” of “9300K” color temperature.

Perform the following operations.

Press the MENU button on the remote control to display the MAIN MENU on the screen, then...

Perform Steps 1-3 of WHITE BAL., then...

Image 37

Vidikron VP-42HD Setting the White Balance, Adjusting the color to the desired level, Perform the following operations

Contents

VP-42 / VP-42HD / VP-50 / VP-60 Owner’s Manual Limited Warranty TABLE OF CONTENTSHow to Attach Options to the Plasma Monitor Installation» Introduction to the Vidikron PlasmaView INTRODUCTIONVP-42 / VP-42HD / VP-50 / VP-60 Flat Panel Display Monitor Contents of the package » The features you’ll enjoy includeIntroduction OptionsIMPORTANT INFORMATION » PrecautionsImportant Information » Warnings and Safety PrecautionsImportant Information » To avoid damage and prolong operating lifeNOTE BURN-INS ARE NOT COVERED BY THE WARRANTY » Plasma monitor cleaning procedureImportant Information WHAT IS COVERED UNDER THE TERMS OF THIS LIMITED WARRANTY LIMITED WARRANTYWHAT IS NOT COVERED UNDER THE TERMS OF THIS LIMITED WARRANTY Limited Warranty EFFECTIVE WARRANTY DATEIMPORTANT WARRANTY REGISTRATION CONTACT A VIDIKRON AUTHORIZED SERVICE CENTER TO OBTAIN SERVICEVIDIKRON ADDITIONAL INFORMATIONLimited Warranty Attn Customer Service Department 2900 Faber Street Union City, CAVentilation Requirements for enclosure mounting HOW TO ATTACH OPTIONS TO THE PLASMA MONITOR3 POWER 1 POWER6 VOLUME DOWN and UP PART NAMES AND FUNCTIONSA AC IN » Rear View / Terminal BoardC VIDEO 1,2,3 BNC, RCA, S-Video D AUDIO1, AUDIO2, AUDIO3Part Names and Functions Rear View / Terminal BoardCb/Pb G/ B/ Y Cb/Pb10 VOLUME + » Remote Control1 ON/OFF 2 CURSOR12 DISPLAY Remote Control continued13 LIGHT Part Names and FunctionsPart Names and Functions » Battery Installation and Replacement1. Press and open the cover 2. Align the batteries according to the + and» Operating Range » Handling the remote controlPart Names and Functions HD Set Top Box with DVI HDCP Output, Computer, other devices INSTALLATION» Connecting Your PC or Macintosh Computer Installation» Connecting Your DVD Player » Connecting Your VCR or Laser Disc PlayerInstallation » Pin Configuration and Signal of the RGB 3 Connector DVI Connector » Pin Assignment and Signal Levels for 15 pin RGB analogInstallation Pin No» VOLUME » POWERTo adjust the sound volume To cancel the soundTo set the timer off » TIMER OFFTo cancel the off timer Basic OperationsLTR BOX mode When viewing videos or DVDsSTD 43 mode ANAMPHC modeAspect Ratio Controls INTELLIWIDE modeActive Image Area 2. Within 3 seconds » Aspect Ratio Operation with Computer SignalsAspect Ratio Controls OSD On Screen Display Controls » Menu Operations Default OSD On Screen Display ControlsReset ADJUSTDefault AUDIO SETUPDefault ResetReset DefaultSETTING SETTINGReset DefaultSIGNAL INFO OSD On Screen Display ControlsAdjusting the picture » Picture Adjust MenuPress the MENU button on the remote control to display the If “CAN NOT ADJUST” appears4. Once the adjustment is completed Setting the picture mode according to the brightness of the room3. To set to “FACTORY” Press the MENU button on the remote control to display theReducing noise in the picture 4. Once the setting is completedPress the MENU button on the remote control to display the MAIN MENU on the screen, thenAdjusting the color to the desired level Setting the White BalancePerform the following operations Perform Steps 1-3 of WHITE BAL., thenChanging the Gamma Curve 7. Once the adjustment is completedAdjusting the white balance OSD On Screen Display Controls4. Once the setting is completed Making the Dither adjustments4. Once the setting is completed OSD On Screen Display Controls5. Once the setting is completed Adjusting the colorsCOLOR CHART Perform the following operationsTo continue adjusting the audio » Audio Setup MenuPress the MENU button on the remote control to display the COLOR CHART settingsSetting the allocation of the audio connectors Set “AUDIO INPUT” on the AUDIO SETUP menu correctly3. To set the AUDIO INPUT1 to “VIDEO2” If “CAN NOT ADJUST” appearsTo select a mode » Image Options Settings Menu2. To adjust the vertical position To continue making other computer image adjustmentsAdjusting the COMPUTER OSD On Screen Display Controls 4. Once all adjustments are completedAdjusting the position of the image Restoring the factory defaults settingsSetting the on-screen menu » SETTING 1 Settings Menu4. To set the DISPLAY OSD to “OFF” Press the MENU button on the remote control to display the3. To set the BNC INPUT mode to “COMP” Setting the BNC connectorsPress the MENU button on the remote control to display the 4. Once the setting is completedPress the MENU button on the remote control to display the 3. To set the RGB select mode to “AUTO”4. Once the setting is completed OSD On Screen Display ControlsPress the MENU button on the remote control to display the 3. To set the HD TYPE mode to “1080B”4. Once the setting is completed Restoring the factory default settings3. To set the INPUT SKIP mode to “OFF” Setting the Input SkipPress the MENU button on the remote control to display the 4. Once the setting is completed4. Once the setting is completed Resetting to the default valuesSETTING OSD On Screen Display ControlsSetting the Auto Off for computer images » SETTING 2 Menu3. To turn the Auto Off function on 4. Once the setting is completedSetting the picture to suit the movie POWER / STANDBY indicatorOSD On Screen Display Controls 3. To set the CINEMA MODE to “OFF” 4. Once the setting is completedPerform Steps 1-2 of PIXL PROTECT, then Dynamic Pixel Protection PIXL PROTECT Reducing burn-in of the screen4. Once the setting is completed OSD On Screen Display ControlsExample Setting ”ORBITER” to “AUTO1” ORBITERLUM. SETTING ORBITER settingsPerform Steps 1-3 of ORBITER, then Adjust the ORBITER function manuallyINVERSE OSD On Screen Display Controls6. Once the setting is completed Setting the time for INVERSE/WHITEPerform Steps 1-3 of INVERSE, then OSD On Screen Display ControlsIMAGE SWEEP Setting the time for IMAGE SWEEP Set a time duration and the speedPerform Steps 1-3 of IMAGE SWEEP, then OSD On Screen Display ControlsSOFTEN Setting the Sidebar Lev. for the sides of the screen6. Once the setting is completed OSD On Screen Display ControlsSetting the screen size for S1/S2 video input 3. To adjust the “SIDEBAR LEV.”OSD On Screen Display Controls 4. Once the setting is completed OSD On Screen Display Controls 3.To set PLUG/PLAY mode to “STB/DVD”Perform the following operations DVI TYPEUsing the timer » SETTING 3 MenuPRESET TIME Perform Steps 1-2 of TIMER, then5. Once the setting is completed The mode switches as follows each time the or buttons is pressedPRESET TIME settings DAYLIGHT SAVING TIMEPerform Steps 1-2 of TIMER, then PROGRAM TIMER6. Once the setting is completed OSD On Screen Display Controls3. To set the DEFAULT INPUT to “VIDEO2” Setting the DEFAULT INPUTPROGRAM TIMER settings To reset the program4. Once the setting is completed Enabling/disabling the front panel controlsOSD On Screen Display Controls Perform the following operations3. To set the CONTROL LOCK to “ON” 3. To set the IR ENABLE to “OFF”4. Once the setting is completed CONTROL LOCK settingsLoop Out Setting OSD On Screen Display Controls 4. Once the setting is completed3. To set the LOOP OUT to “ON” IR ENABLE settings3. To set the ID NUMBER to “O2” ID Number SettingPerform the following operations OSD On Screen Display Controls4. Once the setting is completed Video Wall SettingOSD On Screen Display Controls Perform the following operationsPerform Steps 1-2 of VIDEO WALL, then DIVIDERVIDEO WALL POSITION OSD On Screen Display ControlsAUTO ID DISP. MODEVIDEO WALL POSITION settings DISP. MODE SETTINGSOSD On Screen Display Controls Set the ID number for the No. 1 display on ID NUMBER menu6. Once the setting is completed P. ON DELAY Power on delayOSD On Screen Display Controls Perform Steps 1-2 of VIDEO WALL, then P. ON DELAY settingsOSD On Screen Display Controls LUM SET LINKOSD On Screen Display Controls REPEAT TIMER REPTRPerform Steps 1-2 of VIDEO WALL, then REPTR TIME settings 6. Once the setting is completedOSD On Screen Display Controls 00H01M 00H02M 00H03M .... 04H14M 04H15MSetting the language for the menus » Language Settings Menu3. Once the setting is completed 2. To select “DEUTSCH”OSD On Screen Display Controls 3. Once the setting is completed Setting the video signal format» Video Standard Menu 2. To select “3.58NTSC”Checking the frequencies, polarities of input signals, and resolution » Signal Info. Menu3. Once you have checked the frequency Press the MENU button on the remote control to display theEXTERNAL CONTROLS Type of connector D-Sub 9-pin maleApplication ConnectionsCommunication Format CommandExternal Controls Unit ID 1 and Unit IDExternal Controls Command Reference ListCMD1 CMD202 POWER OFF 01 POWER ON03 INPUT SWITCH CHANGE External Controls05 AUDIO MUTE ON 04 VOLUME GAIN DATA06 AUDIO MUTE OFF 07 CONTRAST GAIN DATA09 SHARPNESS GAIN DATA 08 BRIGHT GAIN DATAExternal Controls 11 TINT GAIN DATA 10 COLOR GAIN DATAExternal Controls 13 WHITE BAL. SELECT 12 IMAGE MEM. SELECTExternal Controls 15 GREEN GAIN DATA 14 RED GAIN DATAExternal Controls 16 BLUE GAIN DATA 17 VID NR MODE SETExternal Controls 19 TREBLE GAIN DATA 18 BASS GAIN DATAExternal Controls ODH +1321 ASPECT RATIO SELECT 20 BALANCE Gain DataExternal Controls 23 H SHIFT GAIN DATA 22 V SHIFT GAIN DATAExternal Controls 25 H-SIZE GAIN DATA 24 V-SIZE GAIN DATAExternal Controls 27 CLOCK GAIN DATA 26 PHASE GAIN DATAExternal Controls 29 OSD ADJ. GAIN DATA 28 OSD SELECTOperation External Controls30 AUTO OFF SELECT 32 CINEMA MODE SET31 SIDEBAR LEV. SET External Controls34 PIXL PROTECT SET 33 RGB3 ADJ. SELECTExternal Controls 36 IMAGE SWEEP SET 35 INVERSE SETExternal Controls STANDBY38 AUDIO SELECT SET 37 FACTORYExternal Controls Example41 RGB SELECT 39 BNC SELECTExternal Controls 42 LANGUAGE SELECT 41 HD SELECTExternal Controls 44 FREQUENCY REQUEST 43 VIDEO STANDARD SELECTExternal Controls Horizontal sync polarityRESOLUTION 45 INPUT MODE REQUESTExternal Controls ACK continuedExternal Controls 46 VIDEO ADJ REQUESTACK continued External Controls 47 AUTO SELECT REQUESTACK continued 49 MODEL NAME REQUEST 48 FAILURE MODE REQUESTExternal Controls Computer input signals supported by this system TABLE OF SIGNALS SUPPORTEDScreen Mode Table of Signals Supported continuedModel Sync PolarityIf you are connecting a composite sync signal, use the HD terminal With digital input some signals are not acceptedTable of Signals Supported continued 7 Other screen modes LTR BOX and I-WIDE are available as wellSYMPTOM TROUBLESHOOTINGCHECKS REMEDYSYMPTOM Troubleshooting continuedCHECKS REMEDYVP-42HD VP-42VP-50 VP-60Limited Warranty Specifications continuedVP-42 VP-42HDVP-42 / VP-42HD DIMENSIONS4.899 1.474 1.665 40.301VP-50 Dimensions3.941 1.667 2.172 48.407Dimensions VP-602.227 58.117 4.855 1.903Ph 510 324-5900 / Fax 510 1-888-4-VIDIKRON RUMA-010550 4-04 VIDIKRON 2900 Faber Street Union City, CA