SSI America 9210 user manual Touch-screen Interface

Page 12

M4557 - Model 9210 Nitriding Controller

Chapter 2 – Touch-screen Interface

Default status screen

Display

The Status display shows the controller information. This information includes data for Loop 1, Loop2 and Loop 3, as well as data for up to four (4) gas flowmeters. The Status display also shows the current Program status, Input/Output Events status and alarm indication. There are six active buttons on the left side of the status display screen: Loops, Menu, Program, Quench Zone, Chart and Alarm Ack.

The “Loops” button will switch the display to the parameters for the active control loops, up to nine parameters. The buttons on the right side of the operator interface allows the operator to look at the “detail” for the loop designated.

The “Menu” button will switch to the operator menu. The “blue” UP and DOWN arrow keys move you from one selection to another.

The “Program” button will switch to the program display. This is a companion display to the status screen and is described below.

The “Quench Zone” button (generally NOT used with the Nitriding Process) will switch to the Quench and Zone display. This is a companion display to the status screen and is described below.

The “Chart” button will switch the display to the video recorder display. Use of the “Chart” display is explained below.

The “Alarm Ack” button will switch to the Active Alarms screen. All Active alarms are displayed on this screen. To acknowledge an alarm, press the UP or DOWN arrow keys to highlight the alarm and press the “Ack” button, located in the lower left side of the screen, to acknowledge the alarm. To acknowledge multiple alarms, repeat the process just described. Return to the Status screen by pressing the “Esc” button.

SSi Manual SERIES 9210-M4557-Nitriding

Page 12 of 12

Image 12
Contents SSi’s Nitriding Control System Table of Contents M4557 Model 9210 Nitriding Controller Safety M4557 Model 9210 Nitriding Controller About This Manual Controller DescriptionModel 9210 Terminals Connections Ethernet Connections Electrical Installation Flash Card & Flash Card ReaderOperator Interface Screen Saver Nitriding Control System Mode of Operation Installation Mounting Stand-alone Flow Panel Copper Brass Galvanized Steel AluminumTouch-screen Interface Loops Display Temp DetailMenu Display Menus M4557 Model 9210 Nitriding Controller Program Display Chart Alarm AckData Logging using Flash Card M4557 Model 9210 Nitriding Controller Configuration Configuration Menu Program EditParameter Value Auxiliary Analog Input Shutdown DisplayDate and Time Slave Communications StatusPID Loop Setup Manual Event ControlChange setpoint overshoot protection Event Run Program Setup Zone / Load TC SetupPort Setup Instrument SetupStep Opcode Temperature Atmosphere Option Zone AssignmentsFurnace Setup None BP Back Pressure TempInternal Loop Instrument 1 Instrument Internal LoopDefault Wait Limits Internal Instrument 1 InstrumentFurnace Name Alarm Setup Relay AssignmentAnalog Input Setup Relay Set PointsAnalog Output Setup Passcode and Alarm IP AddressEvent Control Valve Setup M4557 Model 9210 Nitriding Controller Zero Output Menu Item Security Level Read/Write Raw Data Analog Input Board Setup AUX SP Configuration Programs Overview M4557 Model 9210 Nitriding Controller Series 9210 Opcodes Programmer Description OpcodesM4557 Model 9210 Nitriding Controller M4557 Model 9210 Nitriding Controller M4557 Model 9210 Nitriding Controller M4557 Model 9210 Nitriding Controller M4557 Model 9210 Nitriding Controller Applications Information Standard Event Assignments Typical Nitriding Instrument DesignationsRecipe Step OpCode Temp OptionsJump Recipe High and Low Pressure Switches Vessel Pressure SwitchesFlow Section Nitriding Gas Supply Sample PortsFlow Head Unit Mass Flow MetersGas Solenoids Back Pressure Valve Differential Pressure TransmitterDrip Legs Sample Cell SolenoidM4557 Model 9210 Nitriding Controller System Description Specification Display NA Analog outputs isolated OptionalSensor General Frequency Technical Information Data=xCRLF Error messages System errors Nitriding Sample Cell cleaning TC Type Range in mV E80 J80 K80 N80 NNM Revision History Description Date MCO #