SSI America 9210 user manual Read/Write Raw Data

Page 37

M4557 - Model 9210 Nitriding Controller

Full Calibration

Administrator

Set Menu Security

Administrator

Read/Write Raw Data

Administrator

Curve Entry

Administrator

Alternate PID Setup

Administrator

Analog Input Board Setup

Administrator

AI Board Calibration

Administrator

Program Run

Administrator

PLC Calibration

Administrator

ADAM Correction

Administrator

Aux SP Configuration

Administrator

Read/Write Raw Data

This menu is used to view raw data as stored in the 9210. This is only for use by qualified personnel under direction of SSI. Contact Super Systems Inc at 800-666-4330 before modifying any of these values. The “Read Offset:” at the top of the screen will indicate where in the 9210’s registers the application will begin reading. Press the Edit button to edit the read offset. Press the Read button to read the values from the 9210. The application will read 60 registers at a time. Press the Hex button to convert the values to their hexadecimal counterparts. The Hex button will now read Dec. Pressing the Dec button will convert the values to their decimal counterparts. The Dec button will now read Hex. Pressing the Done button will

close out the menu option. The “Reg:” at the bottom of the screen will indicate where in the 9210’s registers the application will begin writing. Press the left Edit button to edit the write offset. Press the right Edit button (next to the Write button) to edit the value to write to the register. Press the Write button to write the value. Note: This screen does not continuously update, so the Read button will have to be pressed to ensure that any changes were made.

Curve Entry

This menu is not used with the Nitrider Control system and should be ignored.

Alternate PID Setup

This menu is used to allow for up to sixteen different PID Loops that can be used by the control system. These PID loops can be used in place of the PID parameters for Loop 1, 2 or 3. To use an alternate PID for a control Loop, it must be done via the 9210 Recipe. Contact SSI at 800- 666-4330 for assistance with this feature. Use the top blue up and down arrows to select the separate PID loops. Use the bottom up and down arrows to select the parameters for the selected loop. All of the parameters will display a numeric keypad. The “Proportional Band” can range from 0 to 999. The “Reset” can range from

0.00to 10.00. The “Rate” can range from 0.00 to

10.00.The “Integral Preset” can range from –100to

100.The “High Limit” can range from –100to 100. The “Low Limit” can range from –100to 100.

SSi Manual SERIES 9210-M4557-Nitriding

Page 37 of 37

Page 36 Page 38
Image 37
Page 36 Page 38
Contents SSi’s Nitriding Control System Table of Contents M4557 Model 9210 Nitriding Controller Safety M4557 Model 9210 Nitriding Controller Controller Description About This ManualModel 9210 Terminals Connections Ethernet Connections Flash Card & Flash Card Reader Electrical InstallationOperator Interface Screen Saver Nitriding Control System Mode of Operation Copper Brass Galvanized Steel Aluminum Installation Mounting Stand-alone Flow PanelTouch-screen Interface Temp Detail Loops DisplayMenu Display Menus M4557 Model 9210 Nitriding Controller Program Display Alarm Ack ChartData Logging using Flash Card M4557 Model 9210 Nitriding Controller Program Edit Configuration Configuration MenuParameter Value Shutdown Display Auxiliary Analog InputDate and Time Slave Communications StatusManual Event Control PID Loop SetupChange setpoint overshoot protection Zone / Load TC Setup Event Run Program SetupInstrument Setup Port SetupZone Assignments Step Opcode Temperature Atmosphere OptionNone BP Back Pressure Temp Furnace SetupInternal Loop Instrument 1 Instrument Internal LoopInternal Instrument 1 Instrument Default Wait LimitsFurnace Name Relay Assignment Alarm SetupRelay Set Points Analog Input SetupAnalog Output Setup IP Address Passcode and AlarmEvent Control Valve Setup M4557 Model 9210 Nitriding Controller Zero Output Menu Item Security Level Read/Write Raw Data Analog Input Board Setup AUX SP Configuration Programs Overview M4557 Model 9210 Nitriding Controller Opcodes Series 9210 Opcodes Programmer DescriptionM4557 Model 9210 Nitriding Controller M4557 Model 9210 Nitriding Controller M4557 Model 9210 Nitriding Controller M4557 Model 9210 Nitriding Controller M4557 Model 9210 Nitriding Controller Typical Nitriding Instrument Designations Applications Information Standard Event AssignmentsRecipe Step OpCode Temp OptionsJump Recipe Vessel Pressure Switches High and Low Pressure SwitchesFlow Section Nitriding Gas Supply Sample PortsMass Flow Meters Flow Head UnitGas Solenoids Differential Pressure Transmitter Back Pressure ValveDrip Legs Sample Cell SolenoidM4557 Model 9210 Nitriding Controller System Description Display NA Analog outputs isolated Optional SpecificationSensor General Frequency Technical Information Data=xCRLF Error messages System errors Nitriding Sample Cell cleaning TC Type Range in mV E80 J80 K80 N80 NNM MCO # Revision History Description Date
Top Page Image Contents