SSI America 9210 user manual Configuration Configuration Menu, Program Edit, Parameter Value

Page 20

M4557 - Model 9210 Nitriding Controller

Chapter 3 - CONFIGURATION

Configuration Menu

The Configuration Menu is entered through the Menu button that is part of the 6-buttons running down the right side of the default status display screen. Pressing the Login button that is below the blue Up and Down arrow buttons displays a numeric keypad. Enter the correct passcode for the configuration level and press the Enter key. This displays the configuration menu.

Program Edit

Selecting Program Edit displays

another screen, which asks the operator to enter a program number to be edited. Enter 0 to edit a blank program. To erase/delete an existing recipe/program you need to save it as Program Zero (0). Program 0 is a “NO-OP” program. Depending on the 9210’s security setup and current Login status, the user may be first prompted to enter a pass code before being allowed to enter a program number to edit.

When you enter a number for a stored program and push the Enter key the program steps are displayed. Using the up and down arrow keys allow the user select the step in the existing program to edit. Move the cursor to that step and press the Enter key. The next screen to pop up will show the step’s parameter and its value.

NOTE: A list of Op-Codes appears in Chapter 5 of this manual.

Example:

 

Parameter

Value

Opcode

SOAK

Time (hh:mm)

3:45

Highlighting the Opcode line and pressing the Enter button brings up a screen that shows all of the possible Opcodes. Use the Up or Down arrow keys to select the Opcode that you want to use for the program step that you are editing and press the Enter key. To change the Time option, highlight the line and press the Enter key. The next screen is the “Time Edit” screen. If you wish to change the hour, press the Hour button in the upper right-hand corner. If you want to change the minutes press the Min button. The next screen that pops up in both cases is a numeric keypad. Enter the number of hours or minutes that you wish to permanently change the recipe to and press the Enter button. If you DO NOT wish to make any changes press the Esc button.

Press the Set button to save the changes in the program. Notice that the time has been changed on the program segment that you were editing. If you wish to save this change, press the Save button. You will notice that a numeric keypad pops up and asks you to enter the number of the program that you wish to save. It defaults to the program number that you were editing. If this is the program that you wish to save the change, press the Enter key. If you wish to save this as a new program, press the Clr button on the numeric keypad, enter the number of the recipe that you want to save it as and press the Enter button. At this point, Program Editing is done and the display returns back to the Menu screen.

NOTE: See Chapter 6 of this manual for some sample programs.

SSi Manual SERIES 9210-M4557-Nitriding

Page 20 of 20

Image 20
Contents SSi’s Nitriding Control System Table of Contents M4557 Model 9210 Nitriding Controller Safety M4557 Model 9210 Nitriding Controller About This Manual Controller DescriptionModel 9210 Terminals Connections Ethernet Connections Operator Interface Screen Saver Electrical InstallationFlash Card & Flash Card Reader Nitriding Control System Mode of Operation Installation Mounting Stand-alone Flow Panel Copper Brass Galvanized Steel AluminumTouch-screen Interface Loops Display Temp DetailMenu Display Menus M4557 Model 9210 Nitriding Controller Program Display Data Logging using Flash Card ChartAlarm Ack M4557 Model 9210 Nitriding Controller Parameter Value Configuration Configuration MenuProgram Edit Auxiliary Analog Input Shutdown DisplayDate and Time Slave Communications StatusChange setpoint overshoot protection PID Loop SetupManual Event Control Event Run Program Setup Zone / Load TC SetupPort Setup Instrument SetupStep Opcode Temperature Atmosphere Option Zone AssignmentsFurnace Setup None BP Back Pressure TempInternal Loop Instrument 1 Instrument Internal LoopFurnace Name Default Wait LimitsInternal Instrument 1 Instrument Alarm Setup Relay AssignmentAnalog Input Setup Relay Set PointsAnalog Output Setup Passcode and Alarm IP AddressEvent Control Valve Setup M4557 Model 9210 Nitriding Controller Zero Output Menu Item Security Level Read/Write Raw Data Analog Input Board Setup AUX SP Configuration Programs Overview M4557 Model 9210 Nitriding Controller Series 9210 Opcodes Programmer Description OpcodesM4557 Model 9210 Nitriding Controller M4557 Model 9210 Nitriding Controller M4557 Model 9210 Nitriding Controller M4557 Model 9210 Nitriding Controller M4557 Model 9210 Nitriding Controller Applications Information Standard Event Assignments Typical Nitriding Instrument DesignationsRecipe Step OpCode Temp OptionsJump Recipe High and Low Pressure Switches Vessel Pressure SwitchesFlow Section Nitriding Gas Supply Sample PortsGas Solenoids Flow Head UnitMass Flow Meters Back Pressure Valve Differential Pressure TransmitterDrip Legs Sample Cell SolenoidM4557 Model 9210 Nitriding Controller System Description Specification Display NA Analog outputs isolated OptionalSensor General Frequency Technical Information Data=xCRLF Error messages System errors Nitriding Sample Cell cleaning TC Type Range in mV E80 J80 K80 N80 NNM Revision History Description Date MCO #