SSI America 9210 user manual Relay Set Points, Analog Input Setup

Page 29

M4557 - Model 9210 Nitriding Controller

•Programmer alarm

•Alarm 1

•Alarm 2

•Alarm 3

•Event 0 through Event 15

•Burn off

•IN 1 Relay SP A

•IN 1 Relay SP B

•IN 1 Relay SP C

•IN 2 Relay SP A

•IN 2 Relay SP B

•IN 2 Relay SP C

•IN 3 Relay SP A

•IN 3 Relay SP B

•IN 3 Relay SP C

•Alarm Combination (can be any combination below)

•Programmer Alarm

•Alarm 1

•Alarm 2

•Alarm 3

Relay Set Points

This menu screen is not used and should be ignored. Contact Super Systems Inc at 800-666-4330 before making any changes to this screen. This screen will allow the user to set the ON/OFF setpoints for Input 1, 2, and 3 A, B, and C relays. Selecting a setpoint to modify and pressing the Enter button will display a numeric keypad. This can range from –9999to 9999.

Analog Input Setup

This menu option displays a two-level screen with the top level showing the three inputs. Use the blue up and down arrow keys to select one of the inputs.

Pressing the “Enter” key takes you to a menu of parameters that can be assigned to any of the three inputs. Included are thermocouples, voltage, and current inputs.

The lower zone of the “Analog Input Setup” screen contains a table:

Parameter	Value
TC Type	S
Filter Time	0
Initial Scale	0
Full Scale	3000
Decimal Point Location	0
Open TC	Up scale
Input offset	0

SSi Manual SERIES 9210-M4557-Nitriding

Page 29 of 29

Image 29

Contents SSi’s Nitriding Control System Table of Contents M4557 Model 9210 Nitriding Controller Safety M4557 Model 9210 Nitriding Controller Controller Description About This ManualModel 9210 Terminals Connections Ethernet Connections Operator Interface Screen Saver Electrical InstallationFlash Card & Flash Card Reader Nitriding Control System Mode of Operation Copper Brass Galvanized Steel Aluminum Installation Mounting Stand-alone Flow PanelTouch-screen Interface Temp Detail Loops DisplayMenu Display Menus M4557 Model 9210 Nitriding Controller Program Display Data Logging using Flash Card ChartAlarm Ack M4557 Model 9210 Nitriding Controller Parameter Value Configuration Configuration MenuProgram Edit Shutdown Display Auxiliary Analog InputDate and Time Slave Communications StatusChange setpoint overshoot protection PID Loop SetupManual Event Control Zone / Load TC Setup Event Run Program SetupInstrument Setup Port SetupZone Assignments Step Opcode Temperature Atmosphere OptionNone BP Back Pressure Temp Furnace SetupInternal Loop Instrument 1 Instrument Internal LoopFurnace Name Default Wait LimitsInternal Instrument 1 Instrument Relay Assignment Alarm SetupRelay Set Points Analog Input SetupAnalog Output Setup IP Address Passcode and AlarmEvent Control Valve Setup M4557 Model 9210 Nitriding Controller Zero Output Menu Item Security Level Read/Write Raw Data Analog Input Board Setup AUX SP Configuration Programs Overview M4557 Model 9210 Nitriding Controller Opcodes Series 9210 Opcodes Programmer DescriptionM4557 Model 9210 Nitriding Controller M4557 Model 9210 Nitriding Controller M4557 Model 9210 Nitriding Controller M4557 Model 9210 Nitriding Controller M4557 Model 9210 Nitriding Controller Typical Nitriding Instrument Designations Applications Information Standard Event AssignmentsRecipe Step OpCode Temp OptionsJump Recipe Vessel Pressure Switches High and Low Pressure SwitchesFlow Section Nitriding Gas Supply Sample PortsGas Solenoids Flow Head UnitMass Flow Meters Differential Pressure Transmitter Back Pressure ValveDrip Legs Sample Cell SolenoidM4557 Model 9210 Nitriding Controller System Description Display NA Analog outputs isolated Optional SpecificationSensor General Frequency Technical Information Data=xCRLF Error messages System errors Nitriding Sample Cell cleaning TC Type Range in mV E80 J80 K80 N80 NNM MCO # Revision History Description Date