SSI America 9210 user manual Menus

Page 15

M4557 - Model 9210 Nitriding Controller

Event Control

Valve Configuration

Valve Setup

User Calibration

Full Calibration

Set Menu Security

Read/Write Raw Data

Curve Entry

Alternate PID Setup

Analog Input Board Setup

PLC Calibration

ADAM Correction

AUX SP Configuration

Menus

There are four levels of menus in the Series 9210.

The first level is the operator level. These are functions or operations that are typically handled by the furnace operator. This menu is accessed without the need for a pass code.

The second level is to be used by a supervisor. This level requires entry of the level 1 or level 2 pass code.

The third level is the Administrator level. This requires the level 2 pass code ONLY.

The fourth level is the SSi level. This requires a special passcode that can only by obtained by calling SSi at 800-666-4330. These menus are used for configuration setups prior to the instrument being shipped.

As shipped, the level 1 and level 2 codes are set as 1 and 2 respectively. The pass codes can be changed under the Passcode and Alarm menu option.

The Menu screen has five operating buttons located on the right side of the screen. The Up arrow moves the cursor from bottom to top. The Enter button activates the highlighted selection that the operator has chosen, the Down arrow key moves the cursor from top to bottom, the Login key activates another screen that allows access to the user to enter a passcode to set the user level, and the Esc key takes you back to the previous screen without any action being taken.

The selections on the menu that are generally used by the furnace operator are:

Program Run

Slave Communications Status.

Manual Event Control.

Zone/Load TC Setup.

Shutdown

The Program Run screen allows the operator to start/stop/hold/continue recipes, as well as adjust soak time values.

The Slave Communications Status allows the operator to view the communications status with slave instruments.

SSi Manual SERIES 9210-M4557-Nitriding

Page 15 of 15

Image 15
Contents SSi’s Nitriding Control System Table of Contents M4557 Model 9210 Nitriding Controller Safety M4557 Model 9210 Nitriding Controller Controller Description About This ManualModel 9210 Terminals Connections Ethernet Connections Electrical Installation Flash Card & Flash Card ReaderOperator Interface Screen Saver Nitriding Control System Mode of Operation Copper Brass Galvanized Steel Aluminum Installation Mounting Stand-alone Flow PanelTouch-screen Interface Temp Detail Loops DisplayMenu Display Menus M4557 Model 9210 Nitriding Controller Program Display Chart Alarm AckData Logging using Flash Card M4557 Model 9210 Nitriding Controller Configuration Configuration Menu Program EditParameter Value Slave Communications Status Auxiliary Analog InputShutdown Display Date and TimePID Loop Setup Manual Event ControlChange setpoint overshoot protection Zone / Load TC Setup Event Run Program SetupInstrument Setup Port SetupZone Assignments Step Opcode Temperature Atmosphere OptionInternal Loop Furnace SetupNone BP Back Pressure Temp Internal Loop Instrument 1 InstrumentDefault Wait Limits Internal Instrument 1 InstrumentFurnace Name Relay Assignment Alarm SetupRelay Set Points Analog Input SetupAnalog Output Setup IP Address Passcode and AlarmEvent Control Valve Setup M4557 Model 9210 Nitriding Controller Zero Output Menu Item Security Level Read/Write Raw Data Analog Input Board Setup AUX SP Configuration Programs Overview M4557 Model 9210 Nitriding Controller Opcodes Series 9210 Opcodes Programmer DescriptionM4557 Model 9210 Nitriding Controller M4557 Model 9210 Nitriding Controller M4557 Model 9210 Nitriding Controller M4557 Model 9210 Nitriding Controller M4557 Model 9210 Nitriding Controller Options Applications Information Standard Event AssignmentsTypical Nitriding Instrument Designations Recipe Step OpCode TempJump Recipe Sample Ports High and Low Pressure SwitchesVessel Pressure Switches Flow Section Nitriding Gas SupplyFlow Head Unit Mass Flow MetersGas Solenoids Sample Cell Solenoid Back Pressure ValveDifferential Pressure Transmitter Drip LegsM4557 Model 9210 Nitriding Controller System Description Display NA Analog outputs isolated Optional SpecificationSensor General Frequency Technical Information Data=xCRLF Error messages System errors Nitriding Sample Cell cleaning TC Type Range in mV E80 J80 K80 N80 NNM MCO # Revision History Description Date