SSI America 9210 user manual System errors

Page 62

 

 

 

M4557 - Model 9210 Nitriding Controller

 

 

 

 

 

 

System errors:

 

 

 

 

 

 

 

Code

Error

Description

 

 

 

 

 

 

 

71-76

NVRAM CRC error

Three areas exist (1,3 & 5) each with a backup (2,4 & 6). Area 1

 

 

 

 

contains user parameters i.e. calibration data and the backup is write

 

 

 

 

protected so if this area is restored user calibration etc is LOST.

 

 

 

 

Error 71 will be reported in response to any read request until either

 

 

 

 

a calibration is performed or the instrument is rebooted. Areas 3 & 5

 

 

 

 

are read only so they can be silently restored. Errors 73 & 75

 

 

 

 

therefore should never be reported, although they exist internally

 

 

 

 

until they clear themselves. Errors 72,74 & 76 will be reported in

 

 

 

 

response to any read request and cannot be cleared.

 

 

 

 

 

 

 

77- 78

TCD curve error

In reading curve data from EEPROM the instrument has attempted

 

 

 

 

to read beyond the ends of the curve.

 

 

 

 

 

 

 

79

Wrong block no.

The serial numbers of the Nitriding Sample Cell stored in areas 1 & 5

 

 

 

 

(in separate devices) do not match

 

 

 

 

 

 

 

80

UART missing/error.

For debugging only. Since the only interface available is RS232, this

 

 

 

 

error can never be reported!

 

 

 

 

 

 

 

81

Reserved

For external EEPROM not found.

 

 

 

 

 

 

SSi Manual SERIES 9210-M4557-Nitriding

Page 62 of 62

Page 61 Page 63
Image 62
Page 61 Page 63
Contents SSi’s Nitriding Control System Table of Contents M4557 Model 9210 Nitriding Controller Safety M4557 Model 9210 Nitriding Controller About This Manual Controller DescriptionModel 9210 Terminals Connections Ethernet Connections Operator Interface Screen Saver Electrical InstallationFlash Card & Flash Card Reader Nitriding Control System Mode of Operation Installation Mounting Stand-alone Flow Panel Copper Brass Galvanized Steel AluminumTouch-screen Interface Loops Display Temp DetailMenu Display Menus M4557 Model 9210 Nitriding Controller Program Display Data Logging using Flash Card ChartAlarm Ack M4557 Model 9210 Nitriding Controller Parameter Value Configuration Configuration MenuProgram Edit Date and Time Auxiliary Analog InputShutdown Display Slave Communications StatusChange setpoint overshoot protection PID Loop SetupManual Event Control Event Run Program Setup Zone / Load TC SetupPort Setup Instrument SetupStep Opcode Temperature Atmosphere Option Zone AssignmentsInternal Loop Instrument 1 Instrument Furnace SetupNone BP Back Pressure Temp Internal LoopFurnace Name Default Wait LimitsInternal Instrument 1 Instrument Alarm Setup Relay AssignmentAnalog Input Setup Relay Set PointsAnalog Output Setup Passcode and Alarm IP AddressEvent Control Valve Setup M4557 Model 9210 Nitriding Controller Zero Output Menu Item Security Level Read/Write Raw Data Analog Input Board Setup AUX SP Configuration Programs Overview M4557 Model 9210 Nitriding Controller Series 9210 Opcodes Programmer Description OpcodesM4557 Model 9210 Nitriding Controller M4557 Model 9210 Nitriding Controller M4557 Model 9210 Nitriding Controller M4557 Model 9210 Nitriding Controller M4557 Model 9210 Nitriding Controller Recipe Step OpCode Temp Applications Information Standard Event AssignmentsTypical Nitriding Instrument Designations OptionsJump Recipe Flow Section Nitriding Gas Supply High and Low Pressure SwitchesVessel Pressure Switches Sample PortsGas Solenoids Flow Head UnitMass Flow Meters Drip Legs Back Pressure ValveDifferential Pressure Transmitter Sample Cell SolenoidM4557 Model 9210 Nitriding Controller System Description Specification Display NA Analog outputs isolated OptionalSensor General Frequency Technical Information Data=xCRLF Error messages System errors Nitriding Sample Cell cleaning TC Type Range in mV E80 J80 K80 N80 NNM Revision History Description Date MCO #
Top Page Image Contents