Honeywell SG-60 If SW2-2 is set for an External RED system ON, then

Page 44

Airport Systems

§DS32 - 33 – (Figure 2-10, Item 5, Page 2-25) The indications on these lights are dependent on the setting for external red light system on SW2.

If SW2-2 is set for an EXTERNAL RED system (ON), then

DS32 – ON indicates there has been a red light system alarm sometime during the night and the red light system is off, but will reset the next day. OFF when in night mode and the red light system is not in alarm

DS33 – ON indicates in night mode, red lights are turned off and white strobes are operating, OFF indicates NORMAL operation.

If SW2-2 is set for no EXTERNAL RED system (OFF) then

DS32 – ON during DAY and TWILIGHT, OFF during NIGHT mode

DS33 - Not used (lower right of board)

§DS31 – (Figure 2-10, Item 5, Page 2-25) ON indicates power OK, OFF indicates power failure

§DS30 – (Figure 2-10, Item 5, Page 2-25) ON indicates photocell is GOOD, OFF indicates photocell is BAD or not connected

§DS29 – (Figure 2-10, Item 5, Page 2-25) ON indicates all Flashheads are good, OFF indicates one or more Flashheads are bad

2.6.2Flashhead Status Indicators

Miscellaneous Indicators (Figure 2-11, Item 1, Page 2-26)

§ DS1 Red ON for 5-Volt logic power OK

§DS2 Yellow ON for Flash Current Feedback OK

§DS3 Green ON Steady for communications OK (receive & transmit) OFF for no communications reception

Slow Blink (1/sec) for receiving but not being addressed to transmit

Fast Blink (4/sec) for receiving, being addressed to transmit but failing to transmit

2.6.3System Power Up

All switches and indicators listed in this section are in the Master Controller, except for the external system circuit breakers.

1.Verify POWER SWITCH is turned OFF.

2.Verify LOCAL / REMOTE switch is set to LOCAL.

3.Verify MODE switch is set to DAY.

4.Turn on circuit breaker to apply power to Master Controller.

5.Turn on circuit breaker to apply power to Flashheads.

6.Turn POWER SWITCH to ON.

SG-60 High Intensity Strobe System

2-29

Manual EPM-00000019 Rev A

Image 44
Contents Manual Number EPM-00000019-001 Union Place Simi Valley, CA Phone 805 Fax 805Rev Comment Approved DateDisclaimers Table of Contents Troubleshooting Maintenance Safety Information Qualified Personnel EPM-00000019-001 Vii Rev a Scope General DescriptionModel SGC-60 Master Controller Model SGF-60 Flashhead Safety Precautions Airport Systems Specifications Flashhead Fail System Configuration System Controls Power ConfigurationConfiguration Switches Airport Systems Condition 1 You have a Catenary System Flashtube Installation Flashtube Installation Setting the Flashhead Elevation Airport Systems Master Controller Mounting Dimensions Flashhead Outline and Mounting Dimensions Installation Wiring Typical Wiring InstallationBlack wire Photocell White wire PhotocellRed wire Photocell Blue wireControlling the Red Light System Master Controller TB3-C4Master Controller TB5-NO4 Responding to Top Red Beacon Failures9LCA Alarm Card C1 9LCA Alarm Card NC1Flex Conduit Typical Installation Layout Procedures for installation of conduit and tower wiringAirport Systems Airport Systems Flex Conduit Installation Junction Box Wiring Details Flex Conduit Installation Detail Splicing Details for WC000001 Cable WC000001 Cable OverviewAirport Systems Airport Systems 10 Flashhead Cable 10 Master Controller Circuit Board 11 Flashhead Digital Control Board Final Installation Check Power Up and System Tests If SW2-2 is set for an External RED system ON, then If SW2-2 is set for no External RED system OFF thenDay Mode Twilight Mode Night ModeAirport Systems Airport Systems Airport Systems Overall Description SGF-60 FlashheadAirport Systems Airport Systems Power Supplies CommunicationsMode Selection Flash Control Flash FeedbackHigh Voltage Rectification Flashtube TriggeringSGC-60 Master Controller Airport Systems Airport Systems Master Controller Board Schematic SGF-60 Flashhead System Schematic SGF-60 Digital Board Schematic SGF-60 Trigger/High-Voltage Board Schematic Troubleshooting RLC General Troubleshooting All Flashheads Stuck in Day Mode General Troubleshooting Flashhead Does Not Flash General Troubleshooting Flashhead Stuck in Day Mode Dual System-Specific Troubleshooting Catenary System-Specific Troubleshooting Chart SGC-60 Replacement Transformer White wire to the outer bottom right terminal Flashtube Installation Ambient Light Sensor Photocell Replacement Parts Description Part NumberSG-60 AOL Power Supply Component Location SG-60 AOL Flashhead Mounting Dimensions SG-60 AOL Power Supply Mounting Dimensions SG-60 AOL Wiring Installation SG-60 AOL Flashhead Component Locations SG-60 AOL Power Supply Component Locations SG-60 AOL Schematic