Philips SIN 006XN operating instructions Installation, Coffee Brewing

4 INSTALLATION

For your own and for other people's safety, carefully follow the "Safety Regulations" in section 3.

4.1Packaging

The original packaging has been designed to protect the machine during transport. We recommend keeping the packaging for future transport.

4.2Installation instructions

Before installing the machine, read the following safety instructions carefully:

•place the machine in a safe place;

•make sure children cannot play with the machine;

•do not place the machine on hot surfaces or near open flames.

The coffee machine is now ready to be connected to the power supply.

Note: It is recommended to wash the parts before their first use and/or after they have not been

used for a certain period of time.

4.3Machine connection

Electric current can be dangerous! It is therefore essential to follow the safety regulations care- fully. Never use faulty cords! Faulty cords and plugs must be replaced immediately by Authorized Customer

Service Centres.

The voltage of the appliance has been set by the ma- nufacturer. Check that the voltage supplied matches the indications on the identification label on the bottom of the appliance.

•Check that the ON/OFF switch (18) is not pressed before connecting the machine to the power supply.

•Connect the plug to a wall socket with suitable voltage.

4.4 Water tank

•(Fig.1) - Remove the accessory drawer (7), the drip tray

(8) and the grill (9).

•(Fig.2) - Remove the water tank (3). Be careful not to damage the water suction pipe.

•(Fig.3) - Rinse and fill it with fresh drinking water taking care not to overfill.

•(Fig.4) - Reinsert the tank into its seat. Take care to correctly replace the previously extracted pipe

Only use fresh, non-sparkling drinking water to fill the tank. Hot water or any other liquid may damage the tank. Do not turn on the machine without

water: make sure there is enough water in the tank.

Note: For a quick water tank refill, the funnel placed in the upper part of the machine can be used. Open the funnel (Fig.5) and refill with water (Fig.6).

After refilling, always close the funnel.

4.5Priming the water circuit

Before starting up the machine, after long storage and when the water has been used up, the machine’s water circuit must be recharged.

•(Fig.7) - Press the ON/OFF switch (18). The inside light turns on.

•(Fig.8) - Place a container below the steam spout. Open the “hot water/steam” knob (5) by turning it counter- clockwise.

•Wait until a steady jet of water is emitted from the steam spout (pannarello).

•Close the “hot water/steam” knob (5) by turning it clockwise. Remove the container.

The machine is now ready to brew coffee and dispense steam. Please see related sections for operating details.

5 COFFEE BREWING

Caution! Do not remove the “Crema” filter holder by manually turning it clockwise, during the

coffee brewing. Danger of burning.

•During this operation, the "machine ready" coffee switch light (16) may flash on and off; this operation should be considered as normal and not as a fault.

•Before using the machine, make sure that the hot water/ steam knob (5) is closed and that there is sufficient water in the tank.

•(Fig.7) - Press the ON/OFF switch (18). The inside light turns on.

•Wait until the "machine ready" coffee switch light (16) turns up. The machine is now ready for coffee brewing.

5.1 Using ground coffee

•(Fig.9-A)- Insert the filter (12) into the “Crema” filter holder (13).

•(Fig.11) - Insert the filter holder in the Brew unit from the bottom (2).

•(Fig.12) - Turn the filter holder from left to right until it locks in place. Release the grip from the "Crema" filter holder. The handle slightly turns on the left. This movement guarantees the perfect operation of the filter holder.

•(Fig.14) - Preheat the “Crema” filter holder by pressing the coffee switch (16). Water will spill out of the “Crema” filter holder (this operation is only necessary for the first coffee).

• 16 •