3M G5, XT-1 Order Taking Modes Setup, Haptics Vibration Alerts and Blue LED Alerts on H eadsets

Page 25

Configuration

Haptics “Vibration” Alerts and Blue LED Alerts on H eadsets

These options allow you to enable the G5 headset to - Gently vibrate and/or

-Flash a Blue LED (at the tip of the mic boom) when a vehicle is detected at the Order Point These options are, by default, set to YES.

This option only applies to G5 headsets.

If you currently have no G5 headsets and only XT-1 headsets, then enabling or disabling this option will not affect the normal functioning of the XT-1 headset.

Important Notes:

G5 Headsets are backward compatible with Basestation software versions 5.12 and lower, however, the Blue LED Alert and Haptics “Vibration” feature will not be available on these basestation software versions.

The Blue LED Alert and Haptics “Vibration” Alerts a re only available in Basestation software 6.x or greater.

In order to have this feature, you will need to conduct a Basestation software upgrade for which you will need to purchase the following kit:

XT-1 Basestation Software Update Kit XT-1 78-6911-4957-5

The Software upgrade kit consists of :

-An installation CD (including the Install program , basestation software files, and manuals) and the

- USB cable.

Haptics “Vibration” Alerts on Headsets

Perform the following procedure to enable or disable the Haptics “Vibration” Alerts on the Headset upon a vehicle detect at the Order Point

∙Enter the base station configuration mode, see page 11.

∙Change the value for 07 Global Settings > Vibe Alerts on Headsets to YES or NO.

Blue LED Alerts on Headsets

Perform the following procedure to enable or disable the Blue LED Alerts on the

Headset upon a vehicle detect at the Order Point

∙Enter the base station configuration mode, see page 11.

∙Change the value for 07 Global Settings > Blue LED Alerts on Headsets to YES or NO.

Order Taking Modes Setup

Perform the following procedure to enable or disable some of the seven different order taking modes from appearing on the Run Menu:

∙Enter the base station configuration mode, see page 11.

∙Navigate to 09 O.T. Modes Setup.

∙Change the value for each of the following options to Yes or No:

∙Manual Listen/Push To Talk

∙Manual Listen/Manual Latching Talk

∙Auto Listen/Push To Talk

∙Auto Listen/Manual Latching Talk

3M™ Drive-Thru Systems Model G5 and Model XT-1

November 6 2014 – Revision 2.1

Operating Instructions

Page 25 of 77

Page 24 Page 26
Image 25
Page 24 Page 26
Contents Operating Instructions 3M Commercial Solutions Division Table of Contents Assembling a 3M Drive Thru Headset G5 Maintenance Index Alert Message External Trigger InputsOverview Safety InformationImportant Notes and Notes Other ConventionsImportant Note FCC and Industry Canada InformationFCC and IC Identifiers FCC NoteRecycling / Disposal Notice to European Union customers Enter Configuration Mode ConfigurationNavigating the Base Station Display Buttons Interpreting Display InformationConfiguring with a Computer Logging into the Base Station with a PC ∙ Cycle the power to the base stationInbound Microphone Volume Change Basic Volume SettingsOutbound Talk Volume Vehicle Alert VolumeInbound Listen Change the Monitor VolumeOutbound Talk Vehicle PresentVehicle Approach Change the Night VolumeMessages Greeter MessagesAdd Headsets Registering HeadsetsRemove Headsets Resetting Inactive Days List All HeadsetsChange Noise Reduction Level Checking Headset Software RevisionAcoustic Echo Canceller Change Global SettingsDrive Thru Audio Duplex Mode Set System Date and TimeNumber of Base Stations at this Site Channel Heard by Order TakerStore is Now Closed Prompt Customer Order Point Prompt Language Pull Ahead PromptOrder Point Talk with No Vehicle Order Takers and Page Messages in Cross Lane ModeDetector Type Important Notes Kitchen Noise ReductionXT-1 Basestation Software Update Kit XT-1 Order Taking Modes SetupHaptics Vibration Alerts on Headsets Blue LED Alerts on HeadsetsRegular Site Schedule Change Site SchedulingHoliday/Exception Schedule Change Self Monitoring Change Site InformationChange Passcodes User PasscodesInstaller Setup Two Base Station SetupLoad Installation Settings Save Installation SettingsReboot System Factory Setup Restore Factory DefaultsActivate the Backup Intercom Create and Load TemplatesPage 3M Drive Thru Headset G5 OperationNovember 6 2014 Revision Operation 3M Drive-Thru Systems Model G5 and Model XT-1 ∙ T1 and T2 Talkbuttons Connect you to the order point Component Identification and DescriptionG5 Battery Indicator Light Modes Indicator Light ModesG5 Headset Indicator Light Modes Fitting the Headset Replace the Battery Cleaning XT-1 HeadsetsOut of Range Component Identification and Description Headset Replace the Battery Out of Range Navigating in the Base Station in Run Mode Base Station SetupChange Order Taking Mode Listen Auto, Manual, and Always On Explanation of Order Taking ModesTalk Manual Latching, Push to Talk, Automatic Change Lane Mode Which Order Taking Mode to SelectSplit Lane Cross Lane Change Volume ModeG5 Headset MaintenanceReplacing the Carrier Disassembling the Carrier from the PodRefitting the headset with the new Carrier G5 Headset ChargerReplacing the Ear and Headband Pads LocationLow Battery Message Cleaning the Contacts in the Headset Charger wellsG5 Batteries Care, Handling and StorageMaking Sure Batteries are Ready for Use Disposing of BatteriesImportant Information about Rechargeable Batteries Cleaning the Contacts XT-1 Battery ChargerXT-1 Headset XT-1 BatteriesCharging Status Indicator Important Information about Rechargeable Batteries Headset Indicator Lights TroubleshootingG5 Headset Indicator Light Modes Problem Possible Cause Solution General TroubleshootingPress the other button into the correct XT-1 Battery and Battery Charger Battery and Battery Charger TroubleshootingAppendix Declaration of Conformity Physical Appendix Base Station SpecificationsElectrical FunctionalAppendix G5 Charger Specifications Enter the Greeter Configuration Menu Greeter SetupAppendix Greeter Module Record Message Message ActivationChoose Headsets Messages Playback To NameBreakfast Service=StartMessage Daypart Definitions Change Playback Delay TimeGreeter Message Properties Set Greeter Playback through Headsets Change Playback ModeTurn on Tone to Headsets During Greeter Playback Set Playback through MonitorTurn on External Detector Playback Message Turn on Restaurant Closed Playback MessageGreeter Revision Alert & Reminder Message Properties Alert & Reminder Message PropertiesDual Lane Systems Lane Message NamesTandem Pull Ahead Playback Message Delay Count Greeter Setup System DefaultsStart Time Alert & Reminder Properties Greeter Setup Customer SettingsGreeter Setup Example Settings 66, 67, 68, 69 IndexTalk 3M, Thinsulate, Tufcote and ScotchBrite are trademarks of 3M
Related manuals
Manual 8 pages 46.54 Kb
Top Page Image Contents