3M XT-1, G5 operating instructions Component Identification and Description

Page 40

Operation

Component Identification and Description

 

 

Adjustment

 

 

Indicator LED

Slide

 

T2

 

 

 

 

 

 

 

On/Off

Battery

Volume Down

Volume up

Release

 

Page

 

 

 

T1

 

 

 

Figure 2

∙Adjustment Slide: Push or pull to adjust for a comfortable fit.

∙Indicator LED: Indicates operating status of the headset. See Indicator Light Modes below.

∙T1 and T2 (Talk:buttons): Connect you to the order point.

4.When there are two order points, T1 connects to order point 1 and T2 connects to order point 2.

5.When there is only one order point, T1 and T2 both connect to the order point.

6.If you are in Manual Latching or Hands Free modes, the talk button establishes you as the order taker; and while you are the order taker, the talk button is an order point mute button (each tap turns mute on or off to the order point).

∙On/Off: Turns the headset on and off. Hold for 3 seconds to turn off.

∙Volume: The up button increases volume, the down button decreases volume.

∙Page: Has several functions related to in-store communication:

1.Talk to all headsets on the same lane (or both lanes depending upon the configuration), but not to the order point. Press and hold the page button during normal operation to communicate with other headsets. There is an option in Global settings to allow the order taker to hear or not to hear page messages.

2.Release the order-taker. If the order taker taps the page button, he or she is no longer the order taker. The next person to press a talk button becomes the order taker.

3.Enter page monitor mode, which permits you to hear only pages and not any order taking activity. Starting with the power off on the headset, press and hold the page button while turning it on to enable page monitor mode. The headset will stay in this mode until it is powered off and back on.

4.Enter temporary page monitor mode. If an operator (but not the active order taker) taps the page button, the headset will hear only pages and not any order taking activity. The headset will stay in this mode until the operator taps the talk button.

∙Battery Release: Slide up to remove the battery.

November 6 2014 – Revision 2.1

3M™ Drive-Thru Systems Model G5 and Model XT-1

Page 40 of 77

Operating Instructions

Page 39 Page 41
Image 40
Page 39 Page 41
Contents Operating Instructions 3M Commercial Solutions Division Table of Contents Assembling a 3M Drive Thru Headset G5 Maintenance Alert Message External Trigger Inputs IndexSafety Information OverviewOther Conventions Important Notes and NotesImportant Note FCC and Industry Canada InformationFCC Note FCC and IC IdentifiersRecycling / Disposal Notice to European Union customers Enter Configuration Mode ConfigurationNavigating the Base Station Display Interpreting Display Information ButtonsConfiguring with a Computer ∙ Cycle the power to the base station Logging into the Base Station with a PCChange Basic Volume Settings Inbound Microphone VolumeOutbound Talk Volume Vehicle Alert VolumeChange the Monitor Volume Inbound ListenOutbound Talk Vehicle PresentChange the Night Volume Vehicle ApproachMessages Greeter MessagesAdd Headsets Registering HeadsetsRemove Headsets List All Headsets Resetting Inactive DaysChange Noise Reduction Level Checking Headset Software RevisionChange Global Settings Acoustic Echo CancellerDrive Thru Audio Duplex Mode Set System Date and TimeNumber of Base Stations at this Site Channel Heard by Order TakerStore is Now Closed Prompt Pull Ahead Prompt Customer Order Point Prompt LanguageOrder Point Talk with No Vehicle Order Takers and Page Messages in Cross Lane ModeDetector Type Kitchen Noise Reduction Important NotesOrder Taking Modes Setup XT-1 Basestation Software Update Kit XT-1Haptics Vibration Alerts on Headsets Blue LED Alerts on HeadsetsRegular Site Schedule Change Site SchedulingHoliday/Exception Schedule Change Site Information Change Self MonitoringChange Passcodes User PasscodesTwo Base Station Setup Installer SetupLoad Installation Settings Save Installation SettingsFactory Setup Restore Factory Defaults Reboot SystemActivate the Backup Intercom Create and Load TemplatesPage Operation 3M Drive Thru Headset G5November 6 2014 Revision Operation 3M Drive-Thru Systems Model G5 and Model XT-1 Component Identification and Description ∙ T1 and T2 Talkbuttons Connect you to the order pointIndicator Light Modes G5 Battery Indicator Light ModesG5 Headset Indicator Light Modes Fitting the Headset Replace the Battery Cleaning XT-1 HeadsetsOut of Range Component Identification and Description Headset Replace the Battery Out of Range Navigating in the Base Station in Run Mode Base Station SetupChange Order Taking Mode Listen Auto, Manual, and Always On Explanation of Order Taking ModesTalk Manual Latching, Push to Talk, Automatic Change Lane Mode Which Order Taking Mode to SelectSplit Lane Change Volume Mode Cross LaneMaintenance G5 HeadsetReplacing the Carrier Disassembling the Carrier from the PodG5 Headset Charger Refitting the headset with the new CarrierReplacing the Ear and Headband Pads LocationCleaning the Contacts in the Headset Charger wells Low Battery MessageG5 Batteries Care, Handling and StorageMaking Sure Batteries are Ready for Use Disposing of BatteriesImportant Information about Rechargeable Batteries XT-1 Battery Charger Cleaning the ContactsXT-1 Headset XT-1 BatteriesCharging Status Indicator Important Information about Rechargeable Batteries Troubleshooting Headset Indicator LightsG5 Headset Indicator Light Modes General Troubleshooting Problem Possible Cause SolutionPress the other button into the correct Battery and Battery Charger Troubleshooting XT-1 Battery and Battery ChargerAppendix Declaration of Conformity Appendix Base Station Specifications PhysicalElectrical FunctionalAppendix G5 Charger Specifications Enter the Greeter Configuration Menu Greeter SetupAppendix Greeter Module Message Activation Record MessageNameBreakfast Service=Start Choose Headsets Messages Playback ToMessage Daypart Definitions Change Playback Delay TimeGreeter Message Properties Change Playback Mode Set Greeter Playback through HeadsetsTurn on Tone to Headsets During Greeter Playback Set Playback through MonitorTurn on External Detector Playback Message Turn on Restaurant Closed Playback MessageGreeter Revision Alert & Reminder Message Properties Alert & Reminder Message PropertiesMessage Names Dual Lane Systems LaneTandem Pull Ahead Playback Message Delay Count Greeter Setup System DefaultsStart Time Greeter Setup Customer Settings Alert & Reminder PropertiesGreeter Setup Example Settings Index 66, 67, 68, 69Talk 3M, Thinsulate, Tufcote and ScotchBrite are trademarks of 3M
Related manuals
Manual 8 pages 46.54 Kb

G5, XT-1 specifications

The 3M G5 XT-1 is a cutting-edge respirator designed for professionals who require advanced protection in various hazardous environments. With its innovative features, this respirator stands out in the market, providing users with an optimal balance of safety, comfort, and performance.

One of the main features of the 3M G5 XT-1 is its advanced filtration technology. Equipped with highly efficient particulate filters, these respirators are designed to capture airborne particles, including dust, smoke, and other harmful contaminants. This effectiveness is further enhanced by the use of activated carbon in certain filter models, which provides an additional layer of protection against gases and odors. The filters are easy to replace, ensuring that users can maintain their equipment without hassle.

Another key characteristic of the G5 XT-1 is its ergonomic design. The respirator is engineered to provide an excellent fit, reducing the likelihood of leakage and ensuring that users receive optimal protection. The adjustable straps and customizable nose bridge allow for a snug fit on various face shapes and sizes, enhancing comfort during prolonged use. This is particularly important for professionals in fields such as construction, healthcare, and manufacturing, who may wear respirators for extended periods.

The G5 XT-1 also features a lightweight construction, which contributes to user comfort. This lightweight design, combined with features such as breathing valves, enhances airflow, reducing breathing resistance. This means that users can perform their tasks more efficiently while experiencing less fatigue.

Another notable technology integrated into the G5 XT-1 is its dual mode of operation. Users can switch between disposable and reusable options, which is particularly advantageous for those who want to balance cost and sustainability. The reusable aspect of the respirator also encourages environmental friendliness by reducing waste.

In conclusion, the 3M G5 XT-1 respirator is a comprehensive solution for those seeking high-performance respiratory protection. With its advanced filtration technologies, user-centric design, and flexible operation modes, the G5 XT-1 meets the diverse needs of professionals working in challenging environments. Its focus on safety, comfort, and adaptability secures its place as a top choice for respiratory protection in various industries.
Top Page Image Contents