3M XT-1 operating instructions G5 Headset Indicator Light Modes

Page 36

Operation

 

G5 Headset Indicator Light Modes

 

 

 

Indicator

 

Mode Description

 

Indicates power is off.

 

Off (no light)

 

 

Headset is in sleep / hibernate mode. Picking up (or moving) the headset

 

awakens it and the headset will begin to sign on to the base.

 

Headset was signed on, and then went to SLEEP (lights off after 5 minutes of

 

inactivity). When the headset is moved, it wakes up to SOLID GREEN

 

Headset was signed on, and then went to SLEEP and then HIBERNATE (total 10

 

minutes of inactivity). When the headset is moved, it wakes up to Flashing Green

 

(see below)

 

 

Headset battery is completely out of charge or dead.

 

 

 

Solid Green

Headset is signed on,

Lane 1, no car present, standby

 

 

 

Solid Red/Green

Headset is signed on,

Lane 2, no car present, standby

 

 

Solid Red

Headset is in transmitting mode, ie, headset microphone is live. Either Order

 

Taking, or Page mode

 

 

 

Flashing Red/Green

Headset has not registered, but found an open base to which it will try to register.

 

 

Flashing Green

Headset is registered but has not yet synchronized or signed on to the base

(immediately after power on)

station.

 

 

Headset is out of range of basestation

 

 

Flashing Red/Green

Headset is not registered and has not found a base station.

 

 

Steadily Flashing Red

Headset is the active order taker, but the outbound talk to the customer is muted.

 

 

Single Red Flash

Short red flash – Battery is inserted

(changed from flashing green)

Headset is powering up from Hibernate

 

Slightly longer red flash – Headset signs on to the base (as it transitions from

 

flashing green to solid green)

Alternating Flashing Green and Red

Page Monitor Mode.

 

 

 

Red – (Red+Green) – Red – Green -

Headset registered to four base stations.

Red – (Red+Green) – Red – Green..

Perform the following procedure to clear the headset registration data:

 

 

1. Hold down the top end of Volume Control zone with your

 

thumb till you see a Blue light on the end of the mic boom.

 

2. Remove your thumb from the Volume Control zone

 

3. While the Blue light is still on perform the following sequence in a smooth

 

motion

 

 

4. Tap the T1 touch zone 2 times.

 

5. Then, tap the T2 touch zone 2 times

 

6. The Headset LED will blink Red+Green three times and will

 

announce "Powering Off". The headset registration data is

 

now cleared.

 

 

7. The Headset will momentarily turn off and power back again

 

 

 

November 6 2014 – Revision 2.1

3M™ Drive-Thru Systems Model G5 and Model XT-1

Page 36 of 77

Operating Instructions

Image 36
Contents Operating Instructions 3M Commercial Solutions Division Table of Contents Assembling a 3M Drive Thru Headset G5 Maintenance Alert Message External Trigger Inputs IndexSafety Information OverviewOther Conventions Important Notes and NotesImportant Note FCC and Industry Canada InformationFCC Note FCC and IC IdentifiersRecycling / Disposal Notice to European Union customers Configuration Enter Configuration ModeNavigating the Base Station Display Interpreting Display Information ButtonsConfiguring with a Computer ∙ Cycle the power to the base station Logging into the Base Station with a PCChange Basic Volume Settings Inbound Microphone VolumeOutbound Talk Volume Vehicle Alert VolumeChange the Monitor Volume Inbound ListenOutbound Talk Vehicle PresentChange the Night Volume Vehicle ApproachMessages Greeter MessagesRegistering Headsets Add HeadsetsRemove Headsets List All Headsets Resetting Inactive DaysChange Noise Reduction Level Checking Headset Software RevisionChange Global Settings Acoustic Echo CancellerDrive Thru Audio Duplex Mode Set System Date and TimeChannel Heard by Order Taker Number of Base Stations at this SiteStore is Now Closed Prompt Pull Ahead Prompt Customer Order Point Prompt LanguageOrder Takers and Page Messages in Cross Lane Mode Order Point Talk with No VehicleDetector Type Kitchen Noise Reduction Important NotesOrder Taking Modes Setup XT-1 Basestation Software Update Kit XT-1Haptics Vibration Alerts on Headsets Blue LED Alerts on HeadsetsChange Site Scheduling Regular Site ScheduleHoliday/Exception Schedule Change Site Information Change Self MonitoringChange Passcodes User PasscodesTwo Base Station Setup Installer SetupLoad Installation Settings Save Installation SettingsFactory Setup Restore Factory Defaults Reboot SystemActivate the Backup Intercom Create and Load TemplatesPage Operation 3M Drive Thru Headset G5November 6 2014 Revision Operation 3M Drive-Thru Systems Model G5 and Model XT-1 Component Identification and Description ∙ T1 and T2 Talkbuttons Connect you to the order pointIndicator Light Modes G5 Battery Indicator Light ModesG5 Headset Indicator Light Modes Fitting the Headset Replace the Battery XT-1 Headsets CleaningOut of Range Component Identification and Description Headset Replace the Battery Out of Range Base Station Setup Navigating in the Base Station in Run ModeChange Order Taking Mode Explanation of Order Taking Modes Listen Auto, Manual, and Always OnTalk Manual Latching, Push to Talk, Automatic Which Order Taking Mode to Select Change Lane ModeSplit Lane Change Volume Mode Cross LaneMaintenance G5 HeadsetReplacing the Carrier Disassembling the Carrier from the PodG5 Headset Charger Refitting the headset with the new CarrierReplacing the Ear and Headband Pads LocationCleaning the Contacts in the Headset Charger wells Low Battery MessageG5 Batteries Care, Handling and StorageDisposing of Batteries Making Sure Batteries are Ready for UseImportant Information about Rechargeable Batteries XT-1 Battery Charger Cleaning the ContactsXT-1 Headset XT-1 BatteriesCharging Status Indicator Important Information about Rechargeable Batteries Troubleshooting Headset Indicator LightsG5 Headset Indicator Light Modes General Troubleshooting Problem Possible Cause SolutionPress the other button into the correct Battery and Battery Charger Troubleshooting XT-1 Battery and Battery ChargerAppendix Declaration of Conformity Appendix Base Station Specifications PhysicalElectrical FunctionalAppendix G5 Charger Specifications Greeter Setup Enter the Greeter Configuration MenuAppendix Greeter Module Message Activation Record MessageNameBreakfast Service=Start Choose Headsets Messages Playback ToChange Playback Delay Time Message Daypart DefinitionsGreeter Message Properties Change Playback Mode Set Greeter Playback through HeadsetsTurn on Tone to Headsets During Greeter Playback Set Playback through MonitorTurn on Restaurant Closed Playback Message Turn on External Detector Playback MessageGreeter Revision Alert & Reminder Message Properties Alert & Reminder Message PropertiesMessage Names Dual Lane Systems LaneTandem Pull Ahead Playback Message Greeter Setup System Defaults Delay CountStart Time Greeter Setup Customer Settings Alert & Reminder PropertiesGreeter Setup Example Settings Index 66, 67, 68, 69Talk 3M, Thinsulate, Tufcote and ScotchBrite are trademarks of 3M
Related manuals
Manual 8 pages 46.54 Kb

G5, XT-1 specifications

The 3M G5 XT-1 is a cutting-edge respirator designed for professionals who require advanced protection in various hazardous environments. With its innovative features, this respirator stands out in the market, providing users with an optimal balance of safety, comfort, and performance.

One of the main features of the 3M G5 XT-1 is its advanced filtration technology. Equipped with highly efficient particulate filters, these respirators are designed to capture airborne particles, including dust, smoke, and other harmful contaminants. This effectiveness is further enhanced by the use of activated carbon in certain filter models, which provides an additional layer of protection against gases and odors. The filters are easy to replace, ensuring that users can maintain their equipment without hassle.

Another key characteristic of the G5 XT-1 is its ergonomic design. The respirator is engineered to provide an excellent fit, reducing the likelihood of leakage and ensuring that users receive optimal protection. The adjustable straps and customizable nose bridge allow for a snug fit on various face shapes and sizes, enhancing comfort during prolonged use. This is particularly important for professionals in fields such as construction, healthcare, and manufacturing, who may wear respirators for extended periods.

The G5 XT-1 also features a lightweight construction, which contributes to user comfort. This lightweight design, combined with features such as breathing valves, enhances airflow, reducing breathing resistance. This means that users can perform their tasks more efficiently while experiencing less fatigue.

Another notable technology integrated into the G5 XT-1 is its dual mode of operation. Users can switch between disposable and reusable options, which is particularly advantageous for those who want to balance cost and sustainability. The reusable aspect of the respirator also encourages environmental friendliness by reducing waste.

In conclusion, the 3M G5 XT-1 respirator is a comprehensive solution for those seeking high-performance respiratory protection. With its advanced filtration technologies, user-centric design, and flexible operation modes, the G5 XT-1 meets the diverse needs of professionals working in challenging environments. Its focus on safety, comfort, and adaptability secures its place as a top choice for respiratory protection in various industries.